EN 2603:2005

Aerospace series - Port ends for adaptors, threaded, with lockring - Geometric configuration

This standard specifies the dimensional characteristics of the port ends for adaptors, threaded, with lockring, assembly with elastomer O ring, for aerospace applications.
This standard applies to all port ends for adaptors, threaded, with lockring installed in parts defined by EN 2602 and from EN 2607.

Luft- und Raumfahrt - Einschraubzapfen für gerade Einschraubverschraubungen mit Sicherungsring - Konstruktionsblatt

Diese Norm legt die Maße von Einschraubzapfen für gerade Einschraubverschraubungen mit Sicherungsring und Elastomer O Ring zur Verwendung in der Luft- und Raumfahrt fest.
Diese Norm gilt für alle Einschraubzapfen für gerade Einschraubverschraubungen mit Sicherungsring, die in Einschraublöcher nach EN 2602 eingesetzt werden und nach EN 2607 aufgebaut sind.

Série aérospatiale - Extrêmité implantée pour raccords à implanter, filetés avec bague de sécurité - Configuration géométrique

Aeronavtika – Končnice vhodov za adapterje, z navojem, z zaklepnim obročkom – Geometrijski načrt

General Information

• Status: Published
• Publication Date: 06-Dec-2005
• Withdrawal Date: 29-Jun-2006
• ICS: 49.030.99 - Other fasteners
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 07-Dec-2005
• Completion Date: 07-Dec-2005
• Ref Project: SIST EN 2603:2006 - Aerospace series - Port ends for adaptors, threaded, with lockring - Geometric configuration

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Port ends for adaptors, threaded, with lockring - Geometric configurationSérie aérospatiale - Extremité implantée pour raccords a implanter, filetés avec bague de sécurité - Configuration géométriqueLuft- und Raumfahrt - Einschraubzapfen für gerade Einschraubverschraubungen mit Sicherungsring - KonstruktionsblattTa slovenski standard je istoveten z:EN 2603:2005SIST EN 2603:2006en49.030.99ICS:SLOVENSKI
STANDARDSIST EN 2603:200601-september-2006







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2603December 2005ICS 49.030.99 English VersionAerospace series - Port ends for adaptors, threaded, withlockring - Geometric configurationSérie aérospatiale - Raccords droits métriques avec baguede sécurité - Extrêmité implantée - DimensionsLuft- und Raumfahrt - Einschraubzapfen für geradeEinschraubverschraubungen mit Sicherungsring -KonstruktionsblattThis European Standard was approved by CEN on 28 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2603:2005: E



EN 2603:2005 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Required characteristics.5 4 Designation.7



EN 2603:2005 (E) 3 Foreword This European Standard (EN 2603:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at the latest by June 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem-bourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.



EN 2603:2005 (E) 4 1 Scope This standard specifies the dimensional characteristics of the port ends for adaptors, threaded, with lockring, assembly with elastomer O-ring, for aerospace applications. This standard applies to all port ends for adaptors, threaded, with lockring installed in parts defined by EN 2602 and from EN 2607. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer-ences, only the edition cited applies. For undated references, the latest edition of the referenced document (includ
...