iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

FprEN ISO 23779

(Main)

Shot blasting machinery - safety and environmental requirements (ISO/FDIS 23779:2024)

Shot blasting machinery - safety and environmental requirements (ISO/FDIS 23779:2024)

Strahlanlagen - Sicherheits- und Umweltanforderungen (ISO/FDIS 23779:2024)

Équipements de grenaillage - Prescriptions de sécurité et de l'environnement (ISO/FDIS 23779:2024)

Stroji za peskanje - Varnostne in okoljske zahteve (ISO/DIS 23779:2022)

General Information

Status
Not Published
Publication Date
01-Dec-2024
ICS
77.180 - Equipment for the metallurgical industry
Technical Committee
CEN/TC 202 - Foundry machinery
Drafting Committee
CEN/TC 202/WG 4 - Blasting
Current Stage
5020 - Submission to Vote - Formal Approval
Start Date
11-Jul-2024
Completion Date
11-Jul-2024
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
oSIST prEN ISO 23779:2022 - Shot blasting machinery - safety and environmental requirements (ISO/DIS 23779:2022)

Relations

Revises
EN 1248:2001+A1:2009 - Foundry machinery - Safety requirements for abrasive blasting equipment
Effective Date
18-Jan-2023

Buy Standard

prEN ISO 23779:2022prEN ISO 23779:2022
PreviousNext
Draft
prEN ISO 23779:2022
English language
30 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2022
Stroji za peskanje - Varnostne in okoljske zahteve (ISO/DIS 23779:2022)
Shot blasting machinery - safety and environmental requirements (ISO/DIS 23779:2022)
Strahlanlagen - Sicherheits- und Umweltanforderungen (ISO/DIS 23779:2022)
Équipements de grenaillage - Prescriptions de sécurité et de l'environnement (ISO/DIS
23779:2022)
Ta slovenski standard je istoveten z: prEN ISO 23779
ICS:
77.180 Oprema za metalurško Equipment for the
industrijo metallurgical industry
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 23779
ISO/TC 306 Secretariat: SAC
Voting begins on: Voting terminates on:
2022-06-24 2022-09-16
Shot blasting machinery — safety and environmental
requirements
Équipements de grenaillage — Prescriptions de sécurité et de l'environnement
ICS: 77.180; 13.110
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 23779:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

ISO/DIS 23779:2022(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 23779
ISO/TC 306 Secretariat: SAC
Voting begins on: Voting terminates on:

Shot blasting machinery — safety and environmental
requirements
Équipements de grenaillage — Prescriptions de sécurité et de l'environnement
ICS: 77.180; 13.110
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2022
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 23779:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

ISO/DIS 23779:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 3
3 Terms and definitions . 3
4 Significant hazards, environmental impact and energy usage . 5
4.1 General . 5
4.2 Significant hazards . 5
4.3 Environmental impact and energy usage . 5
5 Safety requirements, protective measures, risk reduction measures .5
5.1 General . 5
5.2 Guards and doors . 6
5.3 Electrical equipment . 6
5.4 Noise . 6
5.5 Emergency stop . 6
5.6 Control systems . 6
5.7 Wheel blaster . 7
5.8 Air blaster . 8
5.9 Blasting chamber . . 9
5.10 Shot blasting media transport and recovery system .12
5.11 Power and driving devices . 12
5.12 Loading and unloading systems for workpieces . 13
5.13 Wear related hazards . 13
5.14 Static electricity. 14
5.15 Substances . 14
5.16 Integration with external equipment . 15
6 Energy-efficiency and reduction of environmental impact .15
6.1 General . 15
6.2 Acquisition . 16
6.3 Production . 16
6.4 Use . 16
6.4.1 Input . 16
6.4.2 Output . 17
6.5 End of life . 17
7 Verification of the safety requirements and/or measures .17
8 Information for use .17
8.1 General . 17
8.2 Instruction handbook. 18
8.2.1 Information related to installation . 18
8.2.2 Information related to operation. 18
8.2.3 Information related to maintenance . 18
8.3 Marking . 18
Annex A (informative) Figures of shot blasting machinery .19
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered .23
Bibliography .25
iii
ISO/DIS 23779:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT),see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 306, Foundry machinery.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 23062:2022(Main)
Foundry machinery - Safety requirements for molding and coremaking machinery and associated equipment (ISO 23062:2022)
SIST EN ISO 23062:2023

This document deals with foreseeable significant hazards, hazardous situations and events relevant to molding and coremaking machinery and associated equipment when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 5). It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during the life-cycle phases in accordance with ISO 12100:2010, 5.4, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
This document applies to the following equipment:
a) machinery constructed to condition and/or reclaim foundry sands for mold and coremaking (including related moldable granular materials);
b) molding machinery;
c) coremaking machinery;
d) knock-out equipment;
e) other directly associated equipment.
This document does not apply to:
—    ladles and pouring equipment;
NOTE          This equipment is covered within the European Union (EU) by EN 1247:2010.
—    wax and lost foam pattern production and wax removal equipment;
—    additive manufacturing equipment;
—    dust and/or gaseous emissions reduction equipment;
—    crane installations;
—    winches;
—    continuous conveyors or handling systems which can be an integral part of the equipment covered by this document;
—    sand and casting separation systems.
This document does not explicitly deal with electrical hazards. These hazards are covered by IEC 60204-1: 2016

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN ISO 23063(Main)
Foundry machinery - Safety requirements for high pressure die casting machines (ISO/FDIS 23063:2023)
kSIST FprEN ISO 23063:2023

This document applies to high pressure die casting machines:
a)   hot-chamber die casting machines (horizontal or vertical die closing system), and
b)   horizontal/vertical cold-chamber die casting machines (horizontal or a vertical die closing system).
It applies to high pressure die casting units, i.e., high pressure die casting machines (HPDCM) and their interfaces with the following ancillary equipment:
c)   die,
d)   melting, holding and dosing furnaces (see ISO 13577-1),
e)   metal feeding equipment,
f)   inserting and removal devices,
g)   spraying appliances,
h)   heat exchanger for the die.
This ancillary equipment itself is not covered.
Additional risks arising from the material being cast are not covered.
This standard does not apply to low pressure die casting machines and/or gravity die casting machines.
This standard deal with all significant hazards, hazardous situations and events relevant to pressure die casting machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, use, de-commissioning and maintenance periods, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment

  • Draft
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 23062:2022(Main)
Foundry machinery - Safety requirements for molding and coremaking machinery and associated equipment (ISO 23062:2022)
SIST EN ISO 23062:2023

This document deals with foreseeable significant hazards, hazardous situations and events relevant to molding and coremaking machinery and associated equipment when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 5). It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during the life-cycle phases in accordance with ISO 12100:2010, 5.4, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
This document applies to the following equipment:
a) machinery constructed to condition and/or reclaim foundry sands for mold and coremaking (including related moldable granular materials);
b) molding machinery;
c) coremaking machinery;
d) knock-out equipment;
e) other directly associated equipment.
This document does not apply to:
—    ladles and pouring equipment;
NOTE          This equipment is covered within the European Union (EU) by EN 1247:2010.
—    wax and lost foam pattern production and wax removal equipment;
—    additive manufacturing equipment;
—    dust and/or gaseous emissions reduction equipment;
—    crane installations;
—    winches;
—    continuous conveyors or handling systems which can be an integral part of the equipment covered by this document;
—    sand and casting separation systems.
This document does not explicitly deal with electrical hazards. These hazards are covered by IEC 60204-1: 2016

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15094:2022(Main)
Safety of machinery - Safety requirements for cold flat rolling mills
SIST EN 15094:2022

This document specifies the general safety requirements for cold rolling mills for flat products as defined in 3.1.
This document is applicable to: Plant (machinery, equipment, devices according Annex D) used for the manufacturing of metal cold rolled flat products from the material supply from entry (1), via the mill stand(s) (2) with roll changing devices (4), to the material removal (3) (see Figure 1).
[Figure 1]
This document does not cover:
—   Design and construction of buildings including cellars and their facilities;
—   Thermo process equipment, e.g. in accordance with EN 746 series;
—   Strip processing lines according to EN 15061, e.g. pickling line;
—   Abrasive blasting plants according to EN 1248;
—   Coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e.g. hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles;
—   Roll shop equipment;
—   Hook conveyors according to EN 619;
—   Non-fixed load lifting attachments, e.g. according to EN 13155;
—   Storage equipment (e.g. high-bay warehouses);
—   Cranes, fork lifts, trucks and railway trucks and other vehicles;
—   Process technology (e.g. systems for rolling lubricant, compressed air, treatment of water, cleaning system for exhaust air);
—   Firefighting system.
NOTE 1   Special requirements for protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17449:2022(Main)
Safety of machinery - Safety requirements to finishing lines for metal strip
SIST EN 17449:2022

This document specifies the general safety requirements for finishing lines for metal strip, hereafter referred as finishing line(s), as defined in 3.1.
This document deals with significant hazards, hazardous situations and events relevant for finishing lines when used as intended and under conditions foreseen by the manufacturer. This document provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment (see Clauses 4 and 5).
This document is applicable to:
Plant (machinery, equipment, devices) for the customer-specific processing of metal strip/metal foil (starting material: hot rolled or cold rolled strip as coil) from the material feeding (1) via the finishing process (2) until the material removal (3) (see exemplary layout in Figure 1).
Examples of finishing lines and their machinery/equipment covered by the scope of this document are listed below:
—   finishing lines, e.g.:
—   slitting line (see Figure 2);
—   cut-to-length line (see Figure 3);
—   feeding line (see Figure 4);
—   blanking line;
—   trimming line;
—   rounding machines;
—   strip edge machining lines;
—   inspection lines;
—   rewinding lines, separator lines, doubler lines;
—   strip-supply lines (e.g. for presses or roll forming lines);
—   interlinked machinery/equipment which can be part of a finishing line, e.g.:
—   coil conveying (e.g. feeding in, threading, pushing-in, guiding and transporting);
—   stretching, bending, levelling machine;
—   marking machine;
—   recoiler and uncoiler;
—   shears;
—   punching machine;
—   coil and sleeve handling device;
—   welding machine;
—   oiling machine;
—   scrap chopper, scrap coiler, scrap conveyor;
—   changing device;
—   stacking device;
—   coil transport device (associated with the line);
—   measuring systems and devices;
—   fluid systems.
The following machinery may be part of or linked to a finishing line but are not covered by this document:
—   packaging lines (EN 415);
—   roll forming lines;
—   machines for painting and laminating;
—   embossing machine;
—   saws;
—   plate shear (plate as raw material) (EN 13985);
—   equipment for applying (removing) media to (from) the material surface;
—   coil transport devices outside the boundaries of the line (e.g. supply from the storage);
—   presses (EN ISO 16092-1, EN ISO 16092-2 and EN ISO 16092-3);
—   milling machines (EN ISO 16090-1);
—   machinery using laser (EN ISO 11553) for strip processing (e.g. welding, cutting);
—   punching machines (as stand-alone machine);
—   cranes;
—   robots (EN ISO 10218);
—   separate media systems (e.g. compressed air system, exhaust system);
—   storage equipment.
For modernization, this document can be applied for the parts to be modernized.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14753:2022(Main)
Safety of machinery - Safety requirements for machinery and equipment for continuous casting of steel
SIST EN 14753:2022

This document applies for plant (containing machinery and equipment) used in the process of continuous casting of liquid steel (hereafter referred to as continuous casting machine, CCM) as defined in 3.1.
This document deals with all significant hazards, hazardous situations and events relevant to machinery and equipment for the continuous casting of steel, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This document specifies the safety requirements to be met during design, assembly, transport, commissioning, operation, maintenance (as described in Clause 5) and decommissioning of the equipment.
This document assumes that the machinery and equipment of the plant is operated and maintained by adequately trained and competent personnel (see 7.5). Manual intervention for setting, adjustment and maintenance is accepted as part of the intended use of the plant.
This document assumes that the machinery is used with adequate workstation lighting conforming to EN 12464 1.
National regulations regarding lighting should be considered and could differ from requirements of EN 12464 1.
This document applies to:
—   CCM for the transformation of molten liquid steel into solid products in sections (e.g. square, rectangular, beam blank, circular);
—   CCM's from the point where overhead cranes or other transport systems deposit ladles to CCM (e.g. in a ladle turret, ladle car or ladle stand);
—   via casting process and solidification process;
—   via cutting and marking equipment;
—   thru the run-out-area where the cut product is finished, collected and removed from that area.
This document does not cover safety requirements for:
—   horizontal-CCM for steel;
—   auxiliary plants (auxiliary plants that are outside of the limits of the CCM);
—   ladles and ladle transport;
—   cranes;
—   winches and hoists;
—   conveyors or handling systems;
—   workshop equipment (mould and segment shop, tundish workshop);
—   gas burners, e.g. as a part of pre-heating stations.
This document can be used in case of modernization for the parts to be modernized.
This document is not applicable to CCM's manufactured before the date of its publication.

  • Standard
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15093:2022(Main)
Safety of machinery - Safety requirements for hot flat rolling mills
SIST EN 15093:2022

This document specifies the general safety requirements for hot rolling mills for flat products as defined in 3.1.
This document is applicable to: Plant (machinery, equipment, devices according Annex D) used for the manufacturing of metal hot rolled flat products from the from entry (1), via the mill stands (2) with roll changing devices (6), to the exit (5) (see Figure 1).
This standard does not cover:
—   thermo process equipment, e.g. in accordance with the EN 746 series; including furnaces of a steckel mill;
—   continuous casting machines according to EN 14753;
—   hook conveyors according to EN 619;
—   non-fixed load lifting attachments, e.g. according to EN 13155;
—   roll shop equipment;
—   storage equipment (e.g. high-bay warehouses);
—   cranes, fork lifts, trucks and railway trucks and other vehicles;
—   process technology (e.g. treatment of water, rolling lubricant, compressed air, etc.);
—   separate cleaning system for exhaust air;
—   firefighting system;
NOTE 1   Please refer to Annex C for information regarding the special requirements for protection of persons in case of using asphyxiant gases used in firefighting system.
—   the design of the building, halls and civil works.
This document deals with significant hazards, hazardous situations or hazardous events relevant to hot rolling mills for flat products, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
NOTE 2   For modernization, this document (C-type standard) can be applied for the part to be modernized.
This document is not applicable to hot rolling mills for flat products manufactured before the date of its publication.

  • Standard
    89 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15061:2022(Main)
Safety of machinery - Safety requirements for strip processing line machinery and equipment
SIST EN 15061:2022

This document defines the general safety requirements of strip processing lines.
This document applies to:
Strip processing lines for treating metal strip, from
—   coil take-over-point of the entry section (terminal equipment, see 3.2) through the
—   process (processing and terminal equipment, see 3.3 and 3.2) up to the
—   coil take-over-point of the exit section or interface to other lines (terminal equipment), see Figure 1.
NOTE 1   The aforementioned processes can also occur in combination.
If the aforementioned processes will be combined with processes which are not covered by the scope of this document, this document can be used as a guideline.
NOTE 2   Thermo process equipment integrated in strip processing lines is covered by the EN 746 series. For dryers and ovens, in which flammable substances are released, EN 1539 applies.
This document does not cover:
—   thermo process equipment, e.g. in accordance with the EN 746 series;
—   dryers and ovens in accordance with EN 1539;
—   coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e.g. hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles;
—   acid regeneration plants;
—   regeneration plants which are not integral part of the strip processing line;
—   storage equipment for coils;
—   rolling mill stands (i.e. skin pass and reduction stands) according to EN 15094;
—   rollshop equipment;
—   separate process technology (e.g. compressed air system, treatment of water and treatment of rolling lubricant);
—   separate cleaning system for exhaust air;
—   firefighting systems.
NOTE 3   Protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.
This document deals with foreseeable significant hazards, hazardous situations and events relevant to strip processing lines, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, use, de-commissioning and maintenance periods, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
For modernization, this document (type-C standard) can be applied for the part to be modernized.

  • Standard
    109 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16774:2016(Main)
Safety of machinery - Safety requirements for steel converter and associated equipment
SIST EN 16774:2016

This European Standard applies for steel converter and its associated equipment (hereinafter referred to as converter plant) used in the process of carbon or stainless steel making as defined in 3.1 and illustrated in Annex B.
This European Standard deals with significant hazards, hazardous situations and events relevant to the converter plant. It covers the intended use and foreseeable misuse.
This European Standard specifies the safety requirements to be met during transport, assembly, commissioning, operation, maintenance (as described in Clause 5) and decommissioning/disassembly of the equipment.
This European Standard applies to:
Steel converter and its associated equipment for the oxygen steelmaking process
-   from hot metal/liquid steel and scrap charging;
-   via oxygen refining and stirring;
-   temperature measurement and sampling equipment;
-   up to tapping including slag retaining device;
-   cooling systems;
-   maintenance devices (e.g. relining device, tap hole repair device);
-   process related interfaces/interactions (e.g. according to design, controls) to
-   media,
-   primary and secondary gas cleaning plant,
-   material feeding systems and ladle alloying systems,
-   transfer cars for steel ladle and slag pot, and
-   charging/tapping equipment, e.g. crane, scrap chute, ladles and slag pots.
This European Standard does not cover safety requirements for:
-   usage of process media other than oxygen, nitrogen, argon and compressed air;
-   primary and secondary gas cleaning plants;
-   measuring devices with radioactive sources;
-   material feeding systems and ladle alloying systems;
-   transfer cars for steel ladle and slag pot;
-   charging/tapping and de-slagging equipment, e.g. crane, scrap chutes, ladles and slag pots;
-   auxiliary winches and hoists.
NOTE 1   For variations of converter process where other gases and media, e.g. hydrocarbons, fuels, steam, etc. are used, additional safety measures have to be considered which are not covered in this safety standard
This European Standard is not applicable to converter plant, manufactured before the date of publication of this standard in the Official Journal (OJ).
NOTE 2   In case of revamping, this European Standard can be used as a guideline for the specific parts to be revamped.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1369:2012(Main)
Founding - Magnetic particle testing
SIST EN 1369:2013

This European Standard specifies a magnetic particle testing method for ferro-magnetic iron and steel castings.
NOTE   An iron or steel casting is considered to be ferro-magnetic if the magnetic induction is greater than 1 T (Tesla) for a magnetic field strength of 2,4 kA/m.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day