EN ISO 4641:2024
(Main)Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO 4641:2024)
Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO 4641:2024)
This document specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies.
Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges:
— ambient temperatures: −25 °C to +70 °C;
— water temperatures during operation: 0 °C to +70 °C.
Saug- und Druck-Gummischläuche und ‑schlauchleitungen für Wasser - Anforderungen (ISO 4641:2024)
Dieses Dokument legt die Mindestanforderungen an Gummischläuche und -schlauchleitungen mit Textileinlage und glatter Innenschicht zum Ansaugen und Fördern von Wasser fest.
Drei Bauarten von Schläuchen und Schlauchleitungen sind entsprechend den Anforderungen an die Betriebsbedingungen festgelegt, d. h. Umgebungs- und Wassertemperaturbereiche:
- Umgebungstemperaturen: −25 °C bis +70 °C;
- Wassertemperaturen bei Betrieb: 0 °C bis +70 °C.
Tuyaux et flexibles en caoutchouc pour aspiration et refoulement d'eau - Spécifications (ISO 4641:2024)
Le présent document spécifie les exigences minimales pour les tuyaux et flexibles en caoutchouc à armature textile, à paroi intérieure lisse, utilisés pour l'aspiration et le refoulement de l'eau.
Trois types de tuyaux et de flexibles sont spécifiés selon leurs exigences de service, c'est-à-dire les plages de températures ambiantes et de températures de l'eau:
— températures ambiantes: −25 °C à +70 °C;
— températures de l'eau en service: 0 °C à +70 °C.
Gumene cevi in cevni priključki za dotok in odtok vode - Specifikacija (ISO 4641:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2024
Nadomešča:
SIST EN ISO 4641:2017
Gumene cevi in cevni priključki za dotok in odtok vode - Specifikacija (ISO
4641:2024)
Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO
4641:2024)
Saug- und Druck-Gummischläuche und ‑schlauchleitungen für Wasser - Anforderungen
(ISO 4641:2024)
Tuyaux et flexibles en caoutchouc pour aspiration et refoulement d'eau Spécifications
(ISO 4641:2024)
Ta slovenski standard je istoveten z: EN ISO 4641:2024
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 4641
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 4641:2016
English Version
Rubber hoses and hose assemblies for water suction and
discharge - Specification (ISO 4641:2024)
Tuyaux et flexibles en caoutchouc pour aspiration et Saug- und Druck-Gummischläuche und -
refoulement d'eau - Spécifications (ISO 4641:2024) schlauchleitungen für Wasser - Anforderungen (ISO
4641:2024)
This European Standard was approved by CEN on 22 March 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4641:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 4641:2024) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2024, and conflicting national standards
shall be withdrawn at the latest by November 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4641:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 4641:2024 has been approved by CEN as EN ISO 4641:2024 without any modification.
International
Standard
ISO 4641
Sixth edition
Rubber hoses and hose assemblies
2024-04
for water suction and discharge —
Specification
Tuyaux et flexibles en caoutchouc pour aspiration et refoulement
d'eau — Spécifications
Reference number
ISO 4641:2024(en) © ISO 2024
ISO 4641:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 4641:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Coupling and fittings . 2
6 Materials and construction . 2
6.1 Lining .2
6.2 Reinforcement .2
6.3 Cover .2
7 Dimensions and tolerances . 2
7.1 Inside diameter .2
7.2 Enlarged ends .2
7.3 Unit lengths .3
7.4 Lining .3
7.5 Cover .3
8 Physical properties . 3
8.1 Rubber compounds .3
8.2 Performance requirements for hoses and hose assemblies .3
8.2.1 Hydrostatic-pressure requirements (proof pressure test) .3
8.2.2 Burst test .4
8.2.3 Resistance to bending (minimum bend radius as a function of nominal size) .4
8.2.4 Resistance to suction flattening .4
8.2.5 Low-temperature flexibility.5
8.2.6 Adhesion .5
8.2.7 Ozone resistance of the cover .5
9 Frequency of testing . . 5
10 Marking . . 6
10.1 Hoses .6
10.2 Hose assemblies .6
11 Test report/certificate . 6
12 Packaging and storage . 6
Annex A (normative) Type tests and routine tests . 7
Annex B (informative) Production acceptance tests . 8
Annex C (informative) Couplings and end fittings . 9
Bibliography .10
iii
ISO 4641:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.