EN 13999-2:2007
(Main)Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 2: Determination of volatile organic compounds
Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 2: Determination of volatile organic compounds
This European Standard specifies a method for the determination of single volatile organic compounds (VOC) and of the total amount of volatile organic compounds (TVOCEN13999) in the exhaust air of an emission test chamber after application of a low-solvent or solvent-free adhesive as defined in EN 923. The method is based on use of a solid sorbent with subsequent desorption and gas chromatographic analysis. The method is applicable to measurement of non-polar and slightly polar VOC.
Klebstoffe - Kurzzeit-Verfahren zum Messen der Emissionseigenschaften von lösemittelarmen oder lösemittelfreien Klebstoffen nach der Applikation - Teil 2: Bestimmung flüchtiger organischer Verbindungen
Diese Europäische Norm legt ein Verfahren zur Bestimmung einzelner flüchtiger organischer Verbindungen (VOC) volatile organic compounds) und des Gesamtgehaltes an flüchtigen organischen Verbindungen in der Abluft einer Emissionsprüfkammer nach der Applikation eines Klebstoffes (TVOCEN 13999) fest, wie in EN 923 beschrieben. Das Verfahren beruht auf der Verwendung eines festen Sorptionsmittels mit anschließender Desorption und gaschromatographischer Analyse. Das Verfahren gilt für die Messung von unpolaren und schwach polaren flüchtigen organischen Verbindungen (VOC).
Adhésifs - Méthode de mesurage rapide des caractéristiques émissives des adhésifs à teneur faible ou nulle en solvants après application - Partie 2: Dosage des composés organiques volatils
La présente Norme européenne spécifie une méthode permettant de déterminer la présence de composés organiques volatils spécifiques (COV) et la quantité totale de composés organiques volatils (COV totauxEN13999) dans l’air d’évacuation d’une chambre d’essai d’émission après application d’un adhésif à teneur faible ou nulle en solvants tel que défini dans l’EN 923. Cette méthode repose sur l’utilisation d’un sorbant solide suivie d’une désorption et d’une analyse par chromatographie en phase gazeuse. Elle s’applique au mesurage des COV non polaires et légèrement polaires.
Lepila - Hitra metoda za merjenje emisijskih lastnosti lepil z malo topila ali brez njega po uporabi - 2. del: Določevanje organskih hlapnih spojin
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 2: Determination of volatile organic compoundsAdhésifs - Méthode de mesurage rapide des caractéristiques émissives des adhésifs a teneur faible ou nulle en solvants apres application - Partie 2: Dosage des composés organiques volatilsKlebstoffe - Kurzzeit-Verfahren zum Messen der Emissionseigenschaften von lösemittelarmen oder lösemittelfreien Klebstoffen nach der Applikation - Teil 2: Bestimmung flüchtiger organischer VerbindungenTa slovenski standard je istoveten z:EN 13999-2:2007SIST EN 13999-2:2007en,fr,de83.180LepilaAdhesivesICS:SIST ENV 13999-2:20031DGRPHãþDSLOVENSKI
STANDARDSIST EN 13999-2:200701-september-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13999-2April 2007ICS 83.180Supersedes ENV 13999-2:2002
English VersionAdhesives - Short term method for measuring the emissionproperties of low-solvent or solvent-free adhesives afterapplication - Part 2: Determination of volatile organic compoundsAdhésifs - Méthode de mesurage rapide descaractéristiques émissives des adhésifs à teneur faible ounulle en solvants après application - Partie 2: Dosage descomposés organiques volatilsKlebstoffe - Kurzzeit-Verfahren zum Messen derEmissionseigenschaften von lösemittelarmen oderlösemittelfreien Klebstoffen nach der Applikation - Teil 2:Bestimmung flüchtiger organischer VerbindungenThis European Standard was approved by CEN on 8 March 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13999-2:2007: E
1) Chromosorb 106 and Tenax TA are examples of suitable products available commercially. This information is given for the convenience of users of this European Standard and does not constitute an endorsement by CEN of this product.
An emission test chamber as described in EN 13999-1 or in EN ISO 16000-9 shall be used. 6 Procedure 6.1 Preparation of sampling tubes 6.1.1 Preconditioning Use commercially pre-cleaned sampling tubes containing Tenax TA or sampling tubes that are preconditioned and filled in the laboratory as described for Tenax TA in this clause. For special purposes such as determination of specific carcinogenic volatile organic compounds as foreseen in EN 13999-1 other sorbent materials as described in EN ISO 16017-1 can be taken. Remove trace impurities of manufactured Tenax TA before using it for VOC sampling. The success of the cleaning procedure is checked by performing analysis of the blank sorbent. NOTE EN ISO 16017-1 suggests doing this by keeping the tubes at a temperature of 330 °C for at least 18 h using carrier gas flow of 100 ml/min. Pack one end of the sampling tubes with unsilanised glass wool or stainless steel gauze. Weigh the appropriate amount of adsorbent. Transfer the adsorbent into the tube e.g. using suction. Prior to storage or
EN ISO 16000-9. If the sampling flow rate is determined with a calibrator, start the pump, note and record the sampling flow rate. Connect the sampler to the chamber sampling port, note and record the time the sampler was connected. Never use more than 90 % of the test chamber supply air flow rate as the combined sampling flow rates. At the end of the sampling period disconnect the sampler from the chamber sampling port, note and record the time of disconnection, repeat the sampling flow determination and turn off the pump. Disconnect the sampling tube from the sampling line and seal both
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.