prEN 13631-7

Explosives for civil uses - Explosives - Part 7: Determination of safety and reliability at extreme temperatures

This European Standard specifies the special conditions and procedures permitting the extension to wider ranges of applicability of the following test methods:
- determination of resistance to hydrostatic pressure;
- verification of the means of initiation;
- determination of transmission of detonation.
Standardised test methods at extreme temperatures for the following purposes are not given:
- determination of sensitiveness to friction;
- determination of sensitiveness to impact;
- determination of resistance to water;
- determination of the initiating capability of boosters;
- determination of velocity of detonation.
NOTE   In these cases, the manufacturer of the explosive should provide a suitable test method and, in cases where the results should be checked by an independent institution or authority, the manufacturer and the institution or authority should agree upon a suitable test method.

Explosivstoffe für zivile Zwecke - Explosivstoffe - Teil 7: Bestimmung der Sicherheit und Zuverlässigkeit bei extremen Temperaturen

Explosifs à usage civil - Explosifs - Partie 7: Détermination de la sécurité et de la fiabilité aux températures extrêmes

Eksplozivi za civilno uporabo – Razstreliva – 7. del: Ugotavljanje varnosti in zanesljivosti pri ekstremnih temperaturah

General Information

• Status: Not Published
• Publication Date: 28-Nov-2022
• ICS: 71.100.30 - Explosives. Pyrotechnics and fireworks
• Technical Committee: CEN/TC 321 - Explosives for civil uses
• Drafting Committee: CEN/TC 321/WG 6 - Explosives and propellants
• Current Stage: 4098 - Decision to abandon - Enquiry
• Completion Date: 23-Aug-2023
• Directive: 2014/28/EU - Directive 2014/28/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market and supervision of explosives for civil uses
• Mandate: M/055 - Standardization mandate to CEN for explosives for civil uses
• Mandate: M/562 - Standardization Request on Explosives for civil use
• Ref Project: oSIST prEN 13631-7:2021 - Explosives for civil uses - High explosives - Part 7: Determination of safety and reliability at extreme temperatures

Relations

• Revises: EN 13631-7:2003 - Explosives for civil uses - High explosives - Part 7: Determination of safety and reliability at extreme temperatures
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13631-7:2021
01-april-2021
Eksplozivi za civilno uporabo – Razstreliva – 7. del: Ugotavljanje varnosti in
zanesljivosti pri ekstremnih temperaturah
Explosives for civil uses - High explosives - Part 7: Determination of safety and reliability
at extreme temperatures
Explosivstoffe für zivile Zwecke - Sprengstoffe - Teil 7: Bestimmung der Sicherheit und
Zuverlässigkeit bei extremen Temperaturen
Explosifs à usage civil - Explosifs - Partie 7: Détermination de la sécurité et de la fiabilité
aux températures extrêmes
Ta slovenski standard je istoveten z: prEN 13631-7
ICS:
71.100.30 Eksplozivi. Pirotehnika in Explosives. Pyrotechnics and
ognjemeti fireworks
oSIST prEN 13631-7:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13631-7:2021

---------------------- Page: 2 ----------------------
oSIST prEN 13631-7:2021


DRAFT
EUROPEAN STANDARD
prEN 13631-7
NORME EUROPÉENNE

EUROPÄISCHE NORM

April 2021
ICS 71.100.30 Will supersede EN 13631-7:2003
English Version

Explosives for civil uses - Explosives - Part 7:
Determination of safety and reliability at extreme
temperatures
Explosifs à usage civil - Explosifs - Partie 7: Explosivstoffe für zivile Zwecke - Explosivstoffe - Teil
Détermination de la sécurité et de la fiabilité aux 7: Bestimmung der Sicherheit und Zuverlässigkeit bei
températures extrêmes extremen Temperaturen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 321.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13631-7:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13631-7:2021
prEN 13631-7:2021 (E)
Contents Page

European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Methods . 4
5.1 Method for the determination of resistance to hydrostatic pressure . 4
5.1.1 Temperatures up to 100 °C. 4
5.1.2 Temperatures above 100 °C . 5
5.2 Method for the verification of the means of initiation .
...