iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1514-2:2014

(Main)

Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges

Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges

This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000.
NOTE 1   Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092 4 are given in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 and EN 1514-8.
NOTE 2   Annex A lists information to be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the manufacturer.

Flansche und ihre Verbindungen - Dichtungen für Flansche mit PN-Bezeichnung - Teil 2: Spiraldichtungen für Stahlflansche

Dieser Teil der EN 1514 legt die Maße und Kennzeichnung von Spiraldichtungen zur Verwendung mit
Flanschen mit glatter Dichtfläche (ohne Dichtleiste) und Flanschen mit Dichtleiste nach den Anforderungen der EN 1092-1 für PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 und PN 160 und Nennweiten bis einschließlich DN 1 000 fest.
ANMERKUNG 1      Die Maße für andere Dichtungsformen für die Verwendung mit Flanschen nach EN 1092-1, EN 1092 2, EN 1092-3 und EN 1092-4 sind in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 und EN 1514-8 enthalten.
ANMERKUNG 2      Anhang A enthält Angaben, die vom Anwender bei der Bestellung von Dichtungen anzugeben sind, wenn die Auswahl der für den Anwendungsfall geeigneten Dichtungswerkstoffe dem Hersteller überlassen bleibt.

Brides et leurs assemblages - Joints pour les brides désignées PN - Partie 2 : Joints spiralés pour utilisation avec des brides en acier

La présente partie de l'EN 1514 spécifie les dimensions et le marquage des joints spiralés utilisés avec des brides à face plate et surélevée conformes aux exigences de l'EN 1092-1, pour les pressions nominales PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 et PN 160, et les diamètres nominaux allant jusqu'à DN 1 000 inclus.
NOTE 1   Les dimensions des autres types de joints utilisés avec des brides conformes à l'EN 1092-1, l'EN 1092-2, l'EN 1092-3 et l'EN 1092 4 sont données dans les normes EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 et EN 1514-8.
NOTE 2   L'Annexe A répertorie les informations à fournir par l'acheteur lors de sa commande de joints lorsque le choix des matériaux appropriés à l'utilisation des joints est laissé au fabricant.

Prirobnice in prirobnični spoji - Tesnila za prirobnice z oznako PN - 2. del: Spiralna tesnila za jeklene prirobnice

Standard EN 1514-2 določa mere in označevanje spiralnih tesnil za uporabo skupaj s prirobnicami z ravno čelno ploskvijo in z dvignjeno čelno ploskvijo, ki so v skladu z zahtevami standarda EN 1092-1 za PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 in PN 160 ter do vključno DN 1000.

General Information

Status
Withdrawn
Publication Date
09-Sep-2014
Withdrawal Date
26-Jan-2021
ICS
23.040.80 - Seals for pipe and hose assemblies
Technical Committee
CEN/TC 74 - Flanges and their joints
Drafting Committee
CEN/TC 74/WG 8 - Gaskets
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
27-Jan-2021
Ref Project
SIST EN 1514-2:2014 - Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges

Relations

Replaces
EN 1514-2:2005 - Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
Effective Date
08-Jun-2022
Merged Into
EN 1514-2:2014+A1:2021 - Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
Effective Date
11-Nov-2020
Amended By
EN 1514-2:2014/FprA1:2020 - Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
Effective Date
04-Oct-2017

Buy Standard

EN 1514-2:2014EN 1514-2:2014
PreviousNext
Standard
EN 1514-2:2014
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flansche und ihre Verbindungen - Dichtungen für Flansche mit PN-Bezeichnung - Teil 2: Spiraldichtungen für StahlflanscheBrides et leurs assemblages - Joints pour les brides désignées PN - Partie 2 : Joints spiralés pour utilisation avec des brides en acierFlanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges23.040.80Tesnila za cevne zvezeSeals for pipe and hose assemblies23.040.60Prirobnice, oglavki in spojni elementiFlanges, couplings and jointsICS:Ta slovenski standard je istoveten z:EN 1514-2:2014SIST EN 1514-2:2014en,fr,de01-november-2014SIST EN 1514-2:2014SLOVENSKI
STANDARDSIST EN 1514-2:20051DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1514-2
September 2014 ICS 23.040.80 Supersedes EN 1514-2:2005English Version
Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
Brides et leurs assemblages - Joints pour les brides désignées PN - Partie 2 : Joints spiralés pour utilisation avec des brides en acier
Flansche und ihre Verbindungen - Dichtungen für Flansche mit PN-Bezeichnung - Teil 2: Spiraldichtungen für Stahlflansche This European Standard was approved by CEN on 25 July 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1514-2:2014 ESIST EN 1514-2:2014

Information to be supplied by the purchaser . 15 Bibliography . 16
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1514-1:2024(Main)
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts
SIST EN 1514-1:2024

This document specifies non-metallic flat gaskets, with or without inserts, for use with flanges in accordance with EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092-4, and pipes and fittings in accordance with EN 545, EN 598, and EN 969, for pressure application up to and including PN 63 values and dimensions up to and including DN 4000. In addition, this document also gives guidance on typical materials used and how they should be marked.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12560-1:2024(Main)
Flanges and their joints - Dimensions of gaskets for Class-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts
SIST EN 12560-1:2024

This document specifies the dimensions, types, designation and marking of non-metallic flat gaskets, with or without inserts, for flanges in accordance with EN 1759-1, EN 1759-3 and EN 1759-4, for Class 150, Class 300, Class 600 and Class 900 for nominal sizes DN 15 to DN 600. In addition, this document also gives guidance on typical materials used and how they should be marked.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13555:2021(Main)
Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections
SIST EN 13555:2021

This document specifies the gasket parameters required by EN 1591-1 and provides the test procedures for establishing the values of these parameters.
Gaskets which are wholly based upon elastomers, or based upon elastomers with only the inclusion of particulate fillers or particulate reinforcement, as opposed to gaskets combining elastomers, fillers and fibrous reinforcement, are beyond the scope of this document.
NOTE The testing procedures given might be applicable to gaskets of other shapes and dimensions.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1514-2:2014+A1:2021(Main + Amendment)
Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
SIST EN 1514-2:2014+A1:2021

This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000.
NOTE 1   Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092 4 are given in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 and EN 1514-8.
NOTE 2   Annex A lists information to be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the manufacturer.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14772:2021(Main)
Flanges and their joints - Quality assurance inspection and testing of gaskets in accordance with the series of standards EN 1514 and EN 12560
SIST EN 14772:2021

This document specifies the quality assurance procedures that are applicable to ensure that delivered gaskets comply with the relevant product standards. This document sets down procedures by which a user can have confidence that the salient features of each batch of gaskets or gasket materials delivered to them will be constant.
The gasket types covered by this document are those that are within the scope of the EN 1514 series and EN 12560 series and are simultaneously within the scope of the EN 1591 series. An exception is those gaskets intended solely for domestic fluids (like water, waste water ...) which are based on rubber with or without reinforcement like fillers and/or inserts.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12560-2:2013(Main)
Flanges and their joints - Dimensions of gaskets for Class-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
SIST EN 12560-2:2013

This European Standard specifies the dimensions, design, types, designation, materials and marking of spiral wound gaskets for use with type A flat face or type B raised face flange facings complying with EN 1759-1 for the following Class designations:
-   Class 150, to Class 1 500 for nominal sizes DN 15 to DN 600, and
-   Class designation 2 500 up to and including DN 300.
The centering rings for the spiral wound gaskets according to this standard are sized for use with imperial bolting.
The dimensions of spiral wound gaskets for tongue and groove flange facing types and spigot and recess flange facing types to EN 1759-1 are not included in this standard.
Such gaskets may be available, however, for these types of flange and the purchaser is advised to consult the manufacturer as to their availability. Similarly, for slip-on or screwed flange types, the manufacturer should be consulted about availability.
NOTE   Dimensions of other types of gasket for use with flanges complying with the requirements of EN 1759-1 are given in EN 12560-1, EN 12560-3, EN 12560-4 and EN 12560-5, EN 12560-6 and EN 12560-7.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1514-8:2004(Main)
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 8: Polymeric O-Ring gaskets for grooved flanges
SIST EN 1514-8:2005

This document specifies the dimensions of polymeric O-Ring gaskets for use with grooved flanges complying with EN 1092 for PN 10, PN 16, PN 25, PN 40.
NOTE 1   Dimensions of other types of gaskets for use with flanges to EN 1092 1, EN 1092 2, EN 1092 3 and EN 1092 4 are given in EN 1514 1, EN 1514 2, EN 1514 3, EN 1514 4, EN 1514-6 and EN 1514-7
NOTE 2   Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12560-7:2004(Main)
Flanges and their joints - Gaskets for Class-designated flanges - Part 7: Covered metal jacketed gaskets for use with steel flanges
SIST EN 12560-7:2004

This European Standard specifies the construction, dimensions and marking of covered serrated metal jacketed gaskets for use with flanges complying with prEN 1759 1 for Class 150, Class 300, Class 600, Class 900. Class 1 500 for sizes up to and including NPS 24, and for Class designation 2 500 up to and including NPS 12.
This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them.
NOTE 1   Dimensions of other types of gaskets for use with flanges to prEN 1759 1, EN 1759 3 and EN 1759 4 are given in EN 12560 1, EN 12560 2, EN 12560 3, EN 12560 4, EN 12560 5 and EN 12560 6.
NOTE 2   Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1514-7:2004(Main)
Flanges and their joints - Gaskets for PN-designated flanges - Part 7: Covered metal jacketed gaskets for use with steel flanges
SIST EN 1514-7:2004

This European Standard specifies the construction, dimensions and marking of covered serrated metal jacketed gaskets for use with flanges complying with EN 1092-1 for PN 2,5, PN 6, PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100 up to and including DN 900.
This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them.
NOTE 1   Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-2, EN 1514-3, EN 1514-4, EN 1514-6 and prEN 1514-8.
NOTE 2   Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1514-6:2003(Main)
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 6: Covered serrated metal gaskets for use with steel flanges
SIST EN 1514-6:2004

This European Standard specifies the construction, dimensions and marking of covered serrated metal gaskets for use with flanges complying with EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100 up to and including DN 3000.
This document does not extend to covered serrated metal based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down can be applied to them.
NOTE 1   Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, prEN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-2, EN 1514-3, EN 1514-4, prEN 1514-7 and prEN 1514-8.
NOTE 2   Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day