EN 12560-7:2004

Flanges and their joints - Gaskets for Class-designated flanges - Part 7: Covered metal jacketed gaskets for use with steel flanges

This European Standard specifies the construction, dimensions and marking of covered serrated metal jacketed gaskets for use with flanges complying with prEN 1759 1 for Class 150, Class 300, Class 600, Class 900. Class 1 500 for sizes up to and including NPS 24, and for Class designation 2 500 up to and including NPS 12.
This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them.
NOTE 1   Dimensions of other types of gaskets for use with flanges to prEN 1759 1, EN 1759 3 and EN 1759 4 are given in EN 12560 1, EN 12560 2, EN 12560 3, EN 12560 4, EN 12560 5 and EN 12560 6.
NOTE 2   Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.

Flansche und ihre Verbindungen - Dichtungen für Flansche mit Class-Bezeichnung - Teil 7: Metallummantelte Dichtungen mit Auflage für Stahlflansche

Diese Europäische Norm legt die Ausführung, Maße und Kennzeichnung von metallummantelten Dichtungen mit Auflage für Flansche nach EN 1759-1 für Class 150, Class 300, Class 600, Class 900, Class 1 500 bis ein-schließlich NPS 24 und für Class 2 500 bis einschließlich NPS 12 fest.
Dieses Dokument gilt nicht für metallummantelte Dichtungen mit Auflage für Wärmeaustauscher mit Trennwand-stegen oder große Behälterdichtungen, falls jedoch für diese Dichtungen kein eigenes Dokument vorliegt, können die hier festgelegten Prinzipien angewendet werden.
ANMERKUNG 1   Die Maße für andere Dichtungsformen für Flansche nach prEN 1759-1, prEN 1759-3 und EN 1759-4 sind in EN 12560-1, EN 12560-2, EN 12560-3, EN 12560-4, EN 12560-5 und prEN 12560-6 enthalten.
ANMERKUNG 2   Anhang A enthält Angaben, die der Anwender bei der Bestellung von Dichtungen machen sollte, wenn die Auswahl der für den Anwendungsfall geeigneten Dichtungswerkstoffe dem Lieferer überlassen bleibt.

Brides et leurs assemblages - Joints pour les brides désignées Class - Partie 7: Joints métalloplastiques revêtus pour utilisation avec des brides en acier

La présente Norme européenne prescrit la construction, les dimensions et le marquage des joints métalloplastiques revêtus utilisés avec les brides conformes au prEN 1759-1 pour les désignations Class 150, Class 300, Class 600, Class 900 et Class 1 500, jusqu'à et y compris NPS 24, et pour les désignations Class 2 500, jusqu'à et y compris NPS 12.
La présente Norme européenne ne s'applique pas aux joints métalloplastiques revêtus pour échangeur thermique multi-passes ou grands récipients mais, en l'absence de document consacré à de tels joints, les principes établis peuvent leur être appliqués.
NOTE 1   Les dimensions des autres types de joints utilisés avec des brides conformes aux prEN 1759-1, EN 1759-3 et EN 1759-4 sont données dans les EN 12560-1, EN 12560-2, EN 12560-3, EN 12560-4, EN 12560-5 et EN 12560-6.
NOTE 2   L'Annexe A liste les informations que l'acheteur peut fournir lors de sa commande de joints lorsque le choix des matériaux de joint appropriés à l'utilisation est laissé au fournisseur.

Prirobnice in prirobnični spoji - Tesnila za prirobnice z oznako Class - 7. del: Kovinska oplaščena tesnila za jeklene prirobnice

General Information

• Status: Published
• Publication Date: 08-Jun-2004
• Withdrawal Date: 30-Dec-2004
• ICS: 23.040.80 - Seals for pipe and hose assemblies
• Technical Committee: CEN/TC 74 - Flanges and their joints
• Drafting Committee: CEN/TC 74/WG 8 - Gaskets
• Current Stage: 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
• Start Date: 03-Jun-2024
• Completion Date: 03-Jun-2024
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 12560-7:2004 - Flanges and their joints - Gaskets for Class-designated flanges - Part 7: Covered metal jacketed gaskets for use with steel flanges

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flansche und ihre Verbindungen - Dichtungen für Flansche mit Class-Bezeichnung - Teil 7: Metallummantelte Dichtungen mit Auflage für StahlflanscheBrides et leurs assemblages - Joints pour les brides désignées Class - Partie 7: Joints métalloplastiques revetus pour utilisation avec des brides en acierFlanges and their joints - Gaskets for Class-designated flanges - Part 7: Covered metal jacketed gaskets for use with steel flanges23.040.80Tesnila za cevne zvezeSeals for pipe and hose assemblies23.040.60Prirobnice, oglavki in spojni elementiFlanges, couplings and jointsICS:Ta slovenski standard je istoveten z:EN 12560-7:2004SIST EN 12560-7:2004en01-september-2004SIST EN 12560-7:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12560-7June 2004ICS 23.040.80English versionFlanges and their joints - Gaskets for Class-designated flanges -Part 7: Covered metal jacketed gaskets for use with steelflangesBrides et leurs assemblages - Joints pour les bridesdésignées Class - Partie 7: Joints métalloplastiquesrevêtus pour utilisation avec des brides en acierFlansche und ihre Verbindungen - Dichtungen für Flanschemit Class-Bezeichnung - Teil 7: MetallummantelteDichtungen mit Auflage für StahlflanscheThis European Standard was approved by CEN on 1 April 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12560-7:2004: ESIST EN 12560-7:2004

Information to be supplied by the purchaser.15 Annex B (informative)
A-deviation.16 Bibliography.18
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest by December 2004. The annex A is informative and contains "Information to be supplied by the purchaser". The annex B is informative and contains "A-deviations". EN 12560 consists of 7 parts: Part 1: Non-metallic flat gaskets with or without inserts Part 2: Spiral wound gaskets for use with steel flanges Part 3: Non-metallic PTFE envelope gaskets Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges Part 5: Metallic ring joint gaskets for use with steel flanges Part 6: Covered serrated metal gaskets for use with steel flanges Part 7: Covered metal jacketed gaskets for use with steel flanges According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
metal jacketed gaskets for use with flanges complying with prEN 1759-1 for Class 150, Class 300, Class 600, Class 900. Class 1 500 for sizes up to and including NPS 24, and for Class designation 2 500 up to and including NPS 12. This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them. NOTE 1 Dimensions of other types of gaskets for use with flanges to prEN 1759-1, EN 1759-3 and EN 1759-4 are given in EN 12560-1, EN 12560-2, EN 12560-3, EN 12560-4, EN 12560-5 and EN 12560-6. NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier. 2 Normative references Not applicable. 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 covered metal jacketed gasket consists of a sealing element with or without a location ring which may not be rigidly fixed to the sealing element NOTE The sealing element consists of a metal jacketed core and a conformable sealing material adhered both top and lower metal jacketed core surfaces. 3.2 DN see EN ISO 6708 3.3 NPS see EN 1759-3 3.4 Class see EN 1759-3 4 Designations 4.1 Range of Class designations Gaskets shall be designated as suitable for use with one or more of the following Class designations of flange: Class 150, Class 300, Class 600, Class 900, Class 1 500 and Class 2 500. SIST EN 12560-7:2004

a) Type SC
b) Type C/I
c) Type C/O
d) Type C/IO Figure 1 — Covered metal jacketed gaskets
a) gaskets (C/O or C/IO type) for use with type A (flat face) or type B (raised face) flanges
b) gaskets (SC or C/I type) for use with type C/D (tongue/groove) or type E/F (spigot/recess) flanges Key 1 Centring ring 2 Sealing element 3 Inner ring Figure 2 — Examples of typical covered metal jacketed gaskets configurations SIST EN 12560-7:2004
...