23.040.80 - Seals for pipe and hose assemblies
Seals for pipe and hose assemblies
Dichtungen fur Rohr- und Schlauchverbindungen
Joints d'étanchéité pour tuyauterie et flexibles
Tesnila za cevne zveze
General Information
- 1 (current)
- 2
- 3
- 4
- 5
This document specifies a test method for determining the leaktightness of elastomeric sealing ring
type joints for buried thermoplastics non-pressure piping systems.
Unless otherwise specified in the referring standard, the tests are carried out at the following basic test
pressures:
— p1: internal negative air pressure (partial vacuum);
— p2: a low internal hydrostatic pressure;
— p3: a higher internal hydrostatic pressure.
It also describes the following four test conditions under whic...view more
- Standard17 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft14 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the characteristics of configuration, dimensions, tolerances and mass for
moulded O-Ring seal elements, phosphate ester fluid resistant, for straight thread tube fitting boss for use as
static seals in hydraulic systems for aerospace application.
Application temperature range: −55 °C to 107 °C of continuous operation.
- Standard7 pagesEnglish language
sale 10% off- e-Library read for1 day
EN 1514-2 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000.
- Draft14 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard16 pagesEnglish language
sale 10% off- e-Library read for1 day
This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092 4 are given in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 and EN 1514-8.
NOTE 2 Annex A lists i...view more
- Draft14 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard16 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the gasket parameters required by EN 1591 1 and provides the test procedures for establishing the values of these parameters.
Gaskets which are wholly based upon elastomers, or based upon elastomers with only the inclusion of particulate fillers or particulate reinforcement, as opposed to gaskets combining elastomers, fillers and fibrous reinforcement, are beyond the scope of this document.
NOTE The testing procedures given might be applicable to gaskets of oth...view more
- Draft30 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard34 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the dimensions, design, types, designation, materials and marking of spiral wound gaskets for use with type A flat face or type B raised face flange facings complying with EN 1759-1 for the following Class designations: - Class 150, to Class 1 500 for nominal sizes DN 15 to DN 600, and - Class designation 2 500 up to and including DN 300. The centering rings for the spiral wound gaskets according to this standard are sized for use with imperial bolting. The dimen...view more
- Draft18 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard15 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the dimensions, design, types, designation, materials and marking of spiral wound gaskets for use with type A flat face or type B raised face flange facings complying with EN 1759-1 for the following Class designations:
- Class 150, to Class 1 500 for nominal sizes DN 15 to DN 600, and
- Class designation 2 500 up to and including DN 300.
The centering rings for the spiral wound gaskets according to this standard are sized for use with imperial bolting.
Th...view more
- Draft18 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard15 pagesEnglish language
sale 10% off- e-Library read for1 day
This International Standard applies to all types of surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. This includes components such as valves, filters, regulators, transducers, and controllers. The scope of this standard is limited as follows. a) This standard addresses only surface-mount fluid distribution components and proper sealing methods. This standard is limited to sealing methods using elastomeric mater...view more
- Draft7 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard12 pagesEnglish language
sale 10% off- e-Library read for1 day
applies to all types of surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. This includes components such as valves, filters, regulators, transducers, and controllers
- Draft7 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard12 pagesEnglish language
sale 10% off- e-Library read for1 day
IEC 62339-1:2006 establishes properties and physical dimensions that define the interface for surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. The interface controls the dimensions and location of the sealing surfaces to allow change of just one element of the system without modification of the entire system. This is what makes the system modular from both a design and a maintenance standpoint. It cancels and r...view more
- Standard17 pagesEnglish and French language
sale 15% off
This draft European Standard specifies a method for determination of the long-term sealing pressure of elastomeric seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.
- Standard15 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the technical delivery conditions and quality assurance for gaskets and sheet gasket materials.
- Standard14 pagesEnglish language
sale 10% off- e-Library read for1 day
- 1 (current)
- 2
- 3
- 4
- 5