EN ISO 13705:2001
(Main)Petroleum and natural gas industries - Fired heaters for general refinery service (ISO 13705:2001)
Petroleum and natural gas industries - Fired heaters for general refinery service (ISO 13705:2001)
CEN/TC 12 res 18/2003: approves the publication of a Technical Corrigendum on the German version of EN ISO 13705:2001 (NT/030220).
Erdöl- und Erdgasindustrie - Befeuerte Erhitzer für den allgemeinen Einsatz in Raffinerien (ISO 13705:2002)
In dieser Internationalen Norm werden Anforderungen an und Empfehlungen für Konstruktion, Werkstoffe, Fertigung, Inspektion, Prüfung, Versandvorbereitungen und die Aufstellung von befeuerten Erhitzern, Luftvorwärmern, Lüftern und Brennern festgelegt, die allgemein in Raffinerien betrieben werden.
Industries du pétrole et du gaz naturel - Réchauffeurs à brûleurs pour usage général dans les raffineries (ISO 13705:2001)
Le contenu du corrigendum de mars 2018 a été pris en considération dans cette exemplaire.
Petroleum and natural gas industries - Fired heaters for general refinery service (ISO 13705:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13705:2004
01-maj-2004
Petroleum and natural gas industries - Fired heaters for general refinery service
(ISO 13705:2001)
Petroleum and natural gas industries - Fired heaters for general refinery service (ISO
13705:2001)
Erdöl- und Erdgasindustrie - Befeuerte Erhitzer für den allgemeinen Einsatz in
Raffinerien (ISO 13705:2002)
Industries du pétrole et du gaz naturel - Réchauffeurs a bruleurs pour usage général
dans les raffineries (ISO 13705:2001)
Ta slovenski standard je istoveten z: EN ISO 13705:2001
ICS:
75.180.20 Predelovalna oprema Processing equipment
97.100.01 Grelniki na splošno Heating appliances in
general
SIST EN ISO 13705:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13705:2004
---------------------- Page: 2 ----------------------
SIST EN ISO 13705:2004
EUROPEAN STANDARD
EN ISO 13705
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2001
ICS 75.180.20
English version
Petroleum and natural gas industries - Fired heaters for general
refinery service (ISO 13705:2001)
Industries du pétrole et du gaz naturel - Réchauffeurs à Erdöl- und Erdgasindustrie - Befeuerte Erhitzer für den
brûleurs pour usage général dans les raffineries (ISO allgemeinen Einsatz in Raffinerien (ISO 13705:2002)
13705:2001)
This European Standard was approved by CEN on 15 December 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13705:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13705:2004
EN ISO 13705:2001 (E)
CORRECTED 2002-10-02
Foreword
This document (EN ISO 13705:2001) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum and natural gas industries", the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2002, and conflicting national
standards shall be withdrawn at the latest by June 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of ISO 13705:2001 has been approved by CEN as EN ISO 13705:2001 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13705:2004
INTERNATIONAL ISO
STANDARD 13705
First edition
2001-12-15
Petroleum and natural gas industries —
Fired heaters for general refinery service
Industries du pétrole et du gaz naturel — Réchauffeurs à brûleurs pour
usage général dans les raffineries
Reference number
ISO 13705:2001(E)
©
ISO 2001
---------------------- Page: 5 ----------------------
SIST EN ISO 13705:2004
ISO 13705:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 13705:2004
ISO 13705:2001(E)
Contents Page
Foreword.v
Introduction.vi
1 Scope .1
2 Normative references.1
3 Terms and definitions .3
4 General.11
4.1 Precautions .11
4.2 Pressure design code .11
4.3 Local regulations .11
4.4 Heater nomenclature.11
5 Proposals .16
5.1 Purchaser’s responsibilities.16
5.2 Vendor’s responsibilities.16
5.3 Documentation.17
5.4 Final records .18
6 Design considerations .19
6.1 Process design .19
6.2 Combustion design .19
6.3 Mechanical design.19
7 Tubes .20
7.1 General.20
7.2 Extended surface.21
7.3 Materials .22
8 Headers.22
8.1 General.22
8.2 Plug headers .22
8.3 Return bends.24
8.4 Materials .24
9 Piping, terminals and manifolds .25
9.1 General.25
9.2 Allowable movement and loads .25
9.3 Materials .26
10 Tube supports.26
10.1 General.26
10.2 Loads and allowable stress.27
10.3 Materials .28
11 Refractories and insulation .28
11.1 General.28
11.2 Brick and tile construction .29
11.3 Castable construction.30
11.4 Ceramic fibre construction.30
11.5 Multicomponent lining construction .32
11.6 Materials .32
12 Structures and appurtenances.33
12.1 General.33
12.2 Structures.33
© ISO 2001 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 13705:2004
ISO 13705:2001(E)
12.3 Header boxes, doors and ports.34
12.4 Ladders, platforms and stairways.34
12.5 Materials .35
13 Stacks, ducts and breeching.36
13.1 General.36
13.2 Design considerations .36
13.3 Design methods.38
13.4 Static design.38
13.5 Wind-induced vibration design .39
13.6 Materials .40
14 Burners and auxiliary equipment.40
14.1 Burners .40
14.2 Sootblowers .44
14.3 Fans and drivers .45
14.4 Dampers and damper controls.45
15 Instrument and auxiliary connections.46
15.1 Flue gas and air.46
15.2 Process fluid temperature .47
15.3 Auxiliary connections .47
15.4 Tube skin thermocouples .48
15.5 Access to connections.48
16 Shop fabrication and field erection.48
16.1 General.48
16.2 Structural steel fabrication .48
16.3 Coil fabrication.50
16.4 Painting and galvanizing.50
16.5 Refractories and insulation .51
16.6 Field erection.51
17 Inspection, examination and testing.52
17.1 General.52
17.2 Weld examination .52
17.3 Castings examination.53
17.4 Examination of other components.54
17.5 Testing .54
Annex A (informative) Equipment data sheets.56
Annex B (informative) Purchaser's checklist .85
Annex C (informative) Proposed shop assembly conditions .89
Annex D (normative) Stress curves for use in the design of tube support elements.91
Annex E (normative) Centrifugal fans for fired heater systems.107
Annex F (informative) Air preheat systems for fired process heaters.122
Annex G (informative) Measurement of thermal efficiency of fired process heaters .175
Annex H (informative) Stack design.222
Bibliography .232
iv © ISO 2001 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13705:2004
ISO 13705:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 13705 was prepared by Technical Committee ISO/TC 67, Materials, equipment and
offshore structures for petroleum and natural gas industries, Subcommittee SC 6, Processing equipment and
systems.
Annexes D and E form a normative part of this International Standard. Annexes A, B, C, F, G and H are for
information only.
© ISO 2001 – All rights reserved v
---------------------- Page: 9 ----------------------
SIST EN ISO 13705:2004
ISO 13705:2001(E)
Introduction
This International Standard is based on API standard 560, second edition, September 1995.
Users of this International Standard should be aware that further or differing requirements may be needed for
individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser
from accepting, alternative equipment or engineering solutions for the individual application. This may be
particularly applicable where there is innovative or developing technology. Where an alternative is offered, the
vendor should identify any variations from this International Standard and provide details.
In International Standards, the SI system of units is used. Where practical in this International Standard, US
Customary units are included in brackets for information.
A bullet (zzzz) at the beginning of a clause or subclause indicates that either a decision is required or further
information is to be provided by the purchaser. This information should be indicated on data sheets (see examples
in annex A) or stated in the enquiry or purchase order. Decisions should be indicated on a check list (see example
in annex B).
vi © ISO 2001 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 13705:2004
INTERNATIONAL STANDARD ISO 13705:2001(E)
Petroleum and natural gas industries — Fired heaters for general
refinery service
1 Scope
This International Standard specifies requirements and gives recommendations for the design, materials,
fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters, fans and
burners for general refinery service.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 8501-1, Preparation of steel substrates before application of paints and related products — Visual assessment
of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel
substrates after overall removal of previous coatings
ISO 13704, Petroleum and natural gas industries — Calculation of heater-tube thickness in petroleum refineries
1)
EN 10025 , Hot rolled products of non-alloy structural steels — Technical delivery conditions
2)
AFBMA Standard 9 , Load ratings and fatigue life for ball bearings
3)
AMCA 99-2404-78 , Drive arrangements for centrifugal fans
AMCA 201, Fans and systems
AMCA 210, Laboratory methods of testing fans for aerodynamic performance rating
4)
ASME B17.1 , Keys and keyseats
ASME B31.3, Process piping
ASME Boiler and pressure vessel code, Section VIII, Rules for construction of pressure vessels
5)
ASTM A 36 , Standard specification for carbon structural steel
1) European Committee for Standardization (CEN), Rue de Stassart 36, B-1050 Brussels, Belgium.
th
2) Anti-Friction Bearing Manufacturers Association, 1200 19 Street NW, Suite 300, Washington, DC 20036-2412, USA.
3) Air Movement and Control Assocation, 30 West University Drive, Arlington Heights, IL 60004, USA.
4) American Society of Mechanical Engineers, 3 Park Avenue, New York, NY 10017, USA.
5) American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, USA.
© ISO 2001 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 13705:2004
ISO 13705:2001(E)
ASTM A 105, Standard specification for carbon steel forgings for piping applications
ASTM A 123, Standard specification for zinc (hot-dip galvanized) coatings on iron and steel products
ASTM A 143, Standard practice for safeguarding against embrittlement of hot-dip galvanized structural steel
products and procedure for detecting embrittlement
ASTM A 153, Standard specification for zinc coating (hot-dip) on iron and steel hardware
ASTM A 161, Standard specification for seamless low-carbon and carbon-molybdenum steel still tubes for refinery
service
ASTM A 181, Standard specification for carbon steel forgings, for general-purpose piping
ASTM A 182, Standard specification for forged or rolled alloy-steel pipe flanges, forged fittings, and valves and
parts for high-temperature service
ASTM A 192, Standard specification for seamless carbon steel boiler tubes for high-pressure service
ASTM A 193, Standard specification for alloy-steel and stainless steel bolting materials for high-temperature
service
ASTM A 194, Standard specification for carbon and alloy steel nuts for bolts for high-pressure or high-temperature
service, or both
ASTM A 209, Standard specification for seamless carbon-molybdenum alloy-steel boiler and superheater tubes
ASTM A 210, Standard specification for seamless medium-carbon steel boiler and superheater tubes
ASTM A 213, Standard specification for seamless ferritic and austenitic alloy-steel boiler, superheater and heat-
exchanger tubes
ASTM A 216, Standard specification for steel castings, carbon, suitable for fusion welding, for high-temperature
service
ASTM A 217, Standard specification for steel castings, martensitic stainless and alloy, for pressure-containing
parts, suitable for high-temperature service
ASTM A 234, Standard specification for piping fittings of wrought carbon steel and alloy steel for moderate and high
temperature service
ASTM A 240, Standard specification for heat-resisting chromium and chromium-nickel stainless steel plate, sheet,
and strip for pressure vessels
ASTM A 242, Standard specification for high-strength low-alloy structural steel
ASTM A 283, Standard specification for low and intermediate tensile strength carbon steel plates
ASTM A 297, Standard specification for steel castings, iron-chromium and iron-chromium-nickel, heat resistant, for
general application
ASTM A 307, Standard specification for carbon steel bolts and studs, 60 000 psi tensile strength
ASTM A 320, Standard specification for alloy steel bolting materials for low-temperature service
ASTM A 325, Standard specification for structural bolts, steel, heat treated, 120/105 ksi minimum tensile strength
ASTM A 351, Standard specification for castings, austenitic, austenitic-ferritic (duplex), for pressure-containing
parts
ASTM A 384, Standard practice for safeguarding against warpage and distortion during hot-dip galvanizing of steel
assemblies
2 © ISO 2001 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 13705:2004
ISO 13705:2001(E)
ASTM A 385, Standard practice for providing high-quality zinc coatings (hot-dip)
ASTM A 387, Standard specification for pressure vessel plates, alloy steel, chromium-molybdenum
ASTM A 403, Standard specification for wrought austenitic stainless steel piping fittings
ASTM A 447, Standard specification for steel castings, chromium-nickel-iron alloy (25-12 class), for high-
temperature service
ASTM A 560, Standard specification for castings, chromium-nickel alloy
ASTM A 572, Standard specification for high-strength, low alloy columbium-vanadium structural steel
ASTM A 608, Standard specification for centrifugally cast iron-chromium-nickel high-alloy tubing for pressure
application at high temperatures
ASTM B 366, Standard specification for factory-made wro
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.