Inflation devices and accessories for inflatable consumer products - Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators

This document specifies safety requirements, performance requirements and requirements for marking and labelling of air pumps for inflatable consumer articles including the interface geometry between pump adapters and valves for inflatable consumer articles.
This document does not apply to pumps including tubes and adapters for inflation and deflation.
This document is not applicable to electrical inflators.

Pumpen und Pumpenzubehör für aufblasbare Verbraucherartikel - Teil 2: Sicherheitstechnische Anforderungen, Dauerhaltbarkeit, Gebrauchstauglichkeit, Kompatibilität und Prüfverfahren für Pumpen

Dieses Dokument legt die sicherheitstechnischen Anforderungen, die Anforderungen an die Gebrauchs-tauglichkeit und die Anforderungen an die Kennzeichnung und Beschriftung für Luftpumpen für aufblasbare Verbraucherartikel fest, die geometrische Form der Anschlussstellen zwischen Pumpenadaptern und Ventilen von aufblasbaren Verbraucherartikeln eingeschlossen.
Dieses Dokument gilt nicht für Pumpen, die Schläuche und Adapter zum Auflasen und Luftablassen enthalten.
Dieses Dokument gilt nicht für elektrische Pumpen.

Dispositifs et accessoires de gonflage pour biens de consommation gonflables - Partie 2: Exigences de sécurité, durabilité, performances, compatibilité et méthodes d'essai des gonfleurs

Le présent document prescrit les exigences de sécurité, les exigences de performance et les exigences de marquage et d’étiquetage des pompes à air pour biens de consommation gonflables y compris la géométrie d’interface du côté de l’adaptateur entre les adaptateurs de pompe et les valves pour les biens de consommation gonflables.
Ce document ne s’applique pas aux pompes complètes (ni aux tubes et adaptateurs) pour le gonflage et le dégonflage vendues avec le bien de consommation approprié comme un jeu.
Il ne s’applique pas aux gonfleurs électriques.

Naprave za napihovanje in pripomočki za napihljive potrošniške proizvode - 2. del: Varnostne zahteve, trajnost, ustreznost, združljivost in preskusne metode za naprave za zračne tlačilke

Ta dokument določa varnostne zahteve, zahteve glede ustreznosti ter zahteve za označevanje in etiketiranje zračnih tlačilk za napihljive potrošniške izdelke, vključno z geometrijo vmesnika med adapterji tlačilke in ventili za napihljive potrošniške izdelke.
Ta dokument ne velja za tlačilke s cevmi in adapterji za napihovanje ter izpihovanje.
Ta dokument se ne uporablja za električne zračne tlačilke.

General Information

Status
Published
Publication Date
10-Jan-2012
Current Stage
9093 - Decision to confirm - Review Enquiry
Due Date
02-Sep-2017
Completion Date
22-Sep-2017

Buy Standard

Standard
EN 16051-2:2012
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Pumpen und Pumpenzubehör für aufblasbare Verbraucherartikel - Teil 2: Sicherheitstechnische Anforderungen, Dauerhaltbarkeit, Gebrauchstauglichkeit, Kompatibilität und Prüfverfahren für PumpenPompes et accessoires pour des produits gonflables destinés aux consommateurs - Partie 2: Exigences de sécurité, durabilité, performances, compatibilité et méthodes d' essais des gonfleursInflation devices and accessories for inflatable consumer products - Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators97.220.01Sports equipment and facilities in generalICS:Ta slovenski standard je istoveten z:EN 16051-2:2012SIST EN 16051-2:2012en,fr,de01-marec-2012SIST EN 16051-2:2012SLOVENSKI

STANDARD
SIST EN 16051-2:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16051-2
January 2012 ICS 23.080 English Version

Inflation devices and accessories for inflatable consumer products - Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators

Dispositifs et accessoires de gonflage pour biens de consommation gonflables - Partie 2: Exigences de sécurité, durabilité, performances, compatibilité et méthodes d'essai des gonfleurs

Pumpen und Pumpenzubehör für aufblasbare Verbraucherartikel - Teil 2: Sicherheitstechnische Anforderungen, Dauerhaltbarkeit, Gebrauchstauglichkeit, Kompatibilität und Prüfverfahren für Pumpen This European Standard was approved by CEN on 29 October 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,

B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16051-2:2012: ESIST EN 16051-2:2012

EN 16051-2:2012 (E) 2 Contents Page Foreword ..............................................................................................................................................................3Introduction .........................................................................................................................................................41 Scope ......................................................................................................................................................42 Normative references ............................................................................................................................43 Terms and definitions ...........................................................................................................................44 Air pumps ...............................................................................................................................................54.1 Types of air pumps ................................................................................................................................54.2 Requirements and test methods ..........................................................................................................54.2.1 General ....................................................................................................................................................54.2.2 Safety requirements ..............................................................................................................................54.2.3 Nominal pressure...................................................................................................................................54.2.4 Operational reliability ............................................................................................................................64.2.5 Displaced volume against atmospheric pressure ..............................................................................74.2.6 Adapters and interface dimensions .....................................................................................................74.3 Marking and labelling ............................................................................................................................75 Adapter for plug valves and valve/pump connection with twist lock closure ................................7 SIST EN 16051-2:2012

EN 16051-2:2012 (E) 3 Foreword This document (EN 16051-2:2012) has been prepared by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. EN 16051, Inflation devices and accessories for inflatable consumer products, consists of the following parts:  Part 1: Compatibility of valves and valve adapters  Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. SIST EN 16051-2:2012

EN 16051-2:2012 (E) 4

Introduction The process of inflating a floating leisure article should be considered in two ways: a) the device for inflating the product, a pump; b) the compatibility between the pump and the valve or valves on the product itself.

This standard, EN 16051, is in two parts and addresses the performance, safety requirements, durability and test methods that should be applied to the pump and the compatibility between a pump and the device to be inflated to ensure that the inf

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.