EN 14758-1:2005+A1:2009

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system

This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This European Standard is applicable to PP-MD pipes with or without an integral socket.
NOTE 2   The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3   Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 1 : Spécifications pour les tubes, les raccords et le système

La présente Norme européenne spécifie les exigences pour les tubes, les raccords et le système de canalisations
à paroi compacte, fabriqués à partir de polypropylène avec modificateurs minéraux (PP-MD) et destinés à être utilisés
pour les branchements et les collecteurs d’assainissement enterrés sans pression à l’extérieur de la structure
du bâtiment (code de zone d’application «U»), et pour les branchements et les collecteurs d’assainissement enterrés
sans pression aussi bien à l’intérieur de la structure du bâtiment (code de zone d’application «D») qu’à l’extérieur
de celle-ci.
Ces informations sont précisées dans le marquage des produits par les lettres «U» et «UD».
Elle spécifie également les paramètres d’essai pour les méthodes d’essai référencées dans cette Norme européenne.
La présente Norme européenne couvre une gamme de dimensions nominales, une gamme de séries
de tubes/classes de rigidité et donne des recommandations concernant les couleurs.
NOTE 1 Il est de la responsabilité de l’acheteur ou du prescripteur d’effectuer les choix appropriés à partir de ces données,
en tenant compte des exigences particulières et de toute réglementation nationale applicable ainsi que des pratiques ou codes
de pose.
En relation avec la Partie 2 et la Partie 3 de l’EN 14758 (voir l’Avant-propos), elle s’applique aux tubes et aux raccords
en PP-MD, à leurs assemblages à bague d’étanchéité en élastomère et aux assemblages avec des composants en
matières plastiques et non plastiques différentes destinés à être utilisés dans les systèmes de canalisations enterrés
pour les branchements et l’assainissement sans pression.
La présente Norme européenne est applicable aux tubes PP-MD avec et sans emboîtures.
NOTE 2 Les raccords peuvent être fabriqués par moulage par injection ou être façonnés à partir de tubes et/ou de pièces
moulées.

Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 1. del: Specifikacije za cevi, fitinge in cevni sistem

General Information

• Status: Withdrawn
• Publication Date: 24-Feb-2009
• Withdrawal Date: 06-Mar-2012
• ICS: 93.030 - External sewage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 10 - Systems for non-pressure drainage and sewerage - PE (solid wall)
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 07-Mar-2012
• Completion Date: 07-Mar-2012
• Ref Project: SIST EN 14758-1:2006+A1:2009 - Plastics piping systems for non-pressure underground drainage and sewerage - With mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system

Relations

• Merged From: EN 14758-1:2005 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
• Effective Date: 22-Dec-2008
• Replaced By: EN 14758-1:2012 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
• Effective Date: 12-Jun-2010

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 1. del: Specifikacije za cevi, fitinge in cevni sistemKunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstücke und das RohrleitungssystemSystèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 1 : Spécifications pour les tubes, les raccords et le systèmePlastics piping systems for non-pressure underground drainage and sewerage - With mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 14758-1:2005+A1:2009SIST EN 14758-1:2006+A1:2009en,fr,de01-junij-2009SIST EN 14758-1:2006+A1:2009SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14758-1:2005+A1
February 2009 ICS 93.030 Supersedes EN 14758-1:2005English Version
Plastics piping systems for non-pressure underground drainage and sewerage – Polypropylene with mineral modifiers (PP-MD) -Part 1: Specifications for pipes, fittings and the system
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 1 : Spécifications pour les tubes, les raccords et le système
Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem This European Standard was approved by CEN on 24 November 2005 and includes Amendment 1 approved by CEN on 18 December 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14758-1:2005+A1:2009: ESIST EN 14758-1:2006+A1:2009

General characteristics of PP-MD pipes and fittings . 32 A.1 General . 32 A.2 Material characteristics . 32 A.3 Ring stiffness . 32 SIST EN 14758-1:2006+A1:2009

Standards for pipes and fittings of a material other than PP-MD . 34 Bibliography . 35
There are a number of such system standards. They are supported by separate standards on test methods to which references are made throughout the system standard. The system standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 14758 consists of the following parts under the general title Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene with mineral modifiers (PP-MD) Part 1:
Specifications for pipes, fittings and the system (this document) Part 2:
Guidance for the assessment of conformity (intended to be published as CEN/Technical Specification) Part 3:
Guidance for installation (intended to be published as CEN/Technical Specification). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 14758-1:2006+A1:2009

Elastomeric seals — Material requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber EN 681-2,
Elastomeric seals — Material requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers EN 744:1995,
Plastics piping and ducting systems — Thermoplastics pipes — Test method for resistance to external blows by the round-the-cl
...