EN ISO 7599:2010
(Main)Anodizing of aluminium and its alloys - General specifications for anodic oxidation coatings on aluminium (ISO 7599:2010)
Anodizing of aluminium and its alloys - General specifications for anodic oxidation coatings on aluminium (ISO 7599:2010)
ISO 7599:2010 lays down a method for specifying decorative and protective anodic oxidation coatings on aluminium (including aluminium-based alloys). It defines the characteristic properties of anodic oxidation coatings, lists methods of test for checking the characteristic properties, provides minimum performance requirements, and gives information on the grades of aluminium suitable for anodizing and the importance of pretreatment to ensure the required appearance or texture of the finished work.
It is not applicable to non-porous oxidation coatings of the barrier layer type, oxidation coatings produced by chromic acid or phosphoric acid anodizing, oxidation coatings intended merely to prepare the substrate for subsequent application of organic coatings or electrodeposition of metals, or hard anodic oxidation coatings used mainly for engineering purposes, for which abrasion and wear resistance are the primary characteristics (see ISO 10074).
Anodisieren von Aluminium und Aluminiumlegierungen - Allgemeine Spezifikationen für anodisch erzeugte Oxidschichten auf Aluminium (ISO 7599:2010)
Diese Internationale Norm legt eine Methode zur Spezifizierung dekorativer und schützender anodisch
erzeugter Oxidschichten auf Aluminium (einschließlich der Legierungen auf Grundlage von Aluminium) fest.
Sie definiert die charakteristischen Eigenschaften anodisch erzeugter Oxidschichten, gibt Verfahren zur
Überprüfung der charakteristischen Eigenschaften an, legt Mindestleistungsanforderungen fest, stellt
Informationen zur Güte des zum Anodisieren geeigneten Aluminiums bereit und geht auf die Bedeutung einer
Vorbehandlung zur Sicherstellung des geforderten Aussehens bzw. der Struktur des fertigen Werkstücks ein.
Sie gilt nicht für:
a) porenfreie Oxidschichten, die als Sperrschicht wirken;
b) Oxidschichten, die durch Anodisieren mit Chrom- oder Phosphorsäure erzeugt wurden;
c) Oxidschichten, die lediglich dazu vorgesehen sind, das Grundmetall für die nachfolgende Aufbringung
organischer Schichten oder die elektrolytische Abscheidung von Metallen vorzubereiten;
d) hartanodisierte Schichten, die überwiegend für technische Zwecke verwendet werden, für die Abrieb und
Verschleißfestigkeit die primären Eigenschaften sind (siehe ISO 10074).
Anodisation de l'aluminium et de ses alliages - Spécifications générales pour couches anodiques sur aluminium (ISO 7599:2010)
Aluminij in aluminijeve zlitine - Splošne specifikacije za anodizirane plasti na aluminiju (ISO 7599:2010)
Ta mednarodni standard predpisuje metodo za določanje okrasnih in zaščitnih anodiziranih plasti na aluminiju (vključno z na aluminiju osnovanih zlitin). Določa značilne lastnosti anodiziranih oksidiranih plasti, navaja metode preskusa za preverjanje značilnih lastnosti, zagotavlja minimalne zahteve za delovanje in podaja informacije o razredih aluminija, primernega za anodiziranje ter pomembnost predhodne obdelave za zagotavljanje potrebnega videza teksture končanega dela. Ne velja za a) neporozne plasti pregradne vrste, b) plasti, izdelane s kromovo kislino ali anodizacijo s fosforno kislino, c) plasti, namenjene samo za pripravo substrata za naknadno uporabo organskih plasti ali elektrodepozicijo kovin, d) trde anodizirane plasti, uporabljene predvsem za namene načrtovanja, pri katerih so abrazija in odpornost proti obrabi osnovne značilnosti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7599:2010
01-september-2010
1DGRPHãþD
SIST EN 12373-1:2002
Aluminij in aluminijeve zlitine - Splošne specifikacije za anodizirane plasti na
aluminiju (ISO 7599:2010)
Anodizing of aluminium and its alloys - General specifications for anodic oxidation
coatings on aluminium (ISO 7599:2010)
Anodisieren von Aluminium und Aluminiumlegierungen - Allgemeine Spezifikationen für
anodisch erzeugte Oxidschichten auf Aluminium (ISO 7599:2010)
Anodisation de l'aluminium et de ses alliages - Spécifications générales pour couches
anodiques sur aluminium (ISO 7599:2010)
Ta slovenski standard je istoveten z: EN ISO 7599:2010
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
SIST EN ISO 7599:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 7599:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 7599:2010
EUROPEAN STANDARD
EN ISO 7599
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2010
ICS 25.220.20 Supersedes EN 12373-1:2001
English Version
Anodizing of aluminium and its alloys - General specifications for
anodic oxidation coatings on aluminium (ISO 7599:2010)
Anodisation de l'aluminium et de ses alliages - Anodisieren von Aluminium und Aluminiumlegierungen -
Spécifications générales pour couches anodiques sur Allgemeine Spezifikationen für anodisch erzeugte
aluminium (ISO 7599:2010) Oxidschichten auf Aluminium (ISO 7599:2010)
This European Standard was approved by CEN on 9 June 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7599:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 7599:2010
EN ISO 7599:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 7599:2010
EN ISO 7599:2010 (E)
Foreword
This document (EN ISO 7599:2010) has been prepared by Technical Committee ISO/TC 79 "Light metals and
their alloys" in collaboration with Technical Committee CEN/TC 132 “Aluminium and aluminium alloys” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2011, and conflicting national standards shall be withdrawn at
the latest by January 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12373-1:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 7599:2010 has been approved by CEN as a EN ISO 7599:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 7599:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 7599:2010
INTERNATIONAL ISO
STANDARD 7599
Second edit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.