Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for assessment of conformity

This Technical Specification gives guidance for the assessment of conformity of compounds/formulations, products and assemblies in accordance with EN 1401 1. It applies to those compounds/formulations, products and assemblies intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements of EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to either EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1401 1 (see Foreword), this Technical Specification is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) used for the following puposes:
-   for non pressure underground drainage and sewerage outside the building structure (application area code "U"), reflected in the marking of products by "U";
-   for non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure (application area code "U"), reflected in the marking of products by "UD".

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung der Konformität

Diese Technische Spezifikation enthält Empfehlungen für die Konformitätsbewertung von Formmassen/Zu-sammensetzungen, Erzeugnissen und Bauteilkombinationen nach EN 1401-1. Sie gilt für solche Form-massen/Zusammensetzungen, Erzeugnisse und Bauteilkombinationen, die für eine Verwendung im Qualitätssicherungsplan des Herstellers als Teil des Qualitätsmanagementsystems und zur Einführung von Verfahren der Drittstellenzertifizierung vorgesehen sind. ANMERKUNG 1 Es wird empfohlen, dass das Qualitätsmanagementsystem den Anforderungen von EN ISO 9001 [1] oder mindestens ebenso strengen Anforderungen entspricht. ANMERKUNG 2 Bei Drittstellenzertifizierung wird empfohlen, dass die Zertifizierungsstelle, in Abhängigkeit der Anwendung, nach EN 45011 [2], EN 45012 [3] oder EN ISO/IEC 17021 [4] zugelassen ist. ANMERKUNG 3 Zur Unterstützung der Leser enthält Anhang A einen Überblick über das Prüfsystem. Diese Technische Spezifikation gilt in Verbindung mit EN 1401-1 (siehe Vorwort) für Rohrleitungssysteme aus weichmacherfreiem Polyvinylchlorid (PVC-U) für Abwasserkanäle und -leitungen, die in erdverlegten Schwer-kraftentwässerungssystemen für folgende Verwendungszwecke vorgesehen sind:
- für Anwendungen außerhalb der Gebäudestruktur (Anwendungskennzeichen "U"); auf dem Erzeugnis gekennzeichnet durch "U";
- für Anwendungen sowohl erdverlegt innerhalb der Gebäudestruktur (Anwendungskennzeichen "D") als auch außerhalb der Gebäudestruktur (Anwendungskennzeichen "U") eingesetzt werden; auf dem Erzeugnis gekennzeichnet durch "UD".

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2 : Guide pour l'évaluation de la conformité

La présente Spécification technique fournit un guide pour l’évaluation de la conformité des
compositions/formulations, produits et montages en conformité avec l’EN 1401-1. Elle s’applique aux
compositions/formulations, produits et montages destinés à être inclus dans le plan qualité du fabricant dans
le cadre du système de management de la qualité et pour l’établissement de procédures de certification par
tierce partie.
NOTE 1 Il est recommandé que le système de management de la qualité soit conforme aux exigences pertinentes de
l’EN ISO 9001 [1] ou au moins aussi strict que ces exigences.
NOTE 2 En cas de certification par tierce partie, il est recommandé que l’organisme de certification soit accrédité selon
l’EN 45011 [2], l’EN 45012 [3] ou l’EN ISO/CEI 17021 [4], suivant le cas.
NOTE 3 Afin d’aider le lecteur, une matrice d’essais de base est fournie en Annexe A.
Conjointement avec l’EN 1401-1 (voir l’Avant-propos), la présente Spécification technique s’applique aux
systèmes de canalisations fabriqués à partir de poly(chlorure de vinyle) non plastifié (PVC-U) utilisés pour les
applications suivantes :
- pour les branchements et les collecteurs d’assainissement enterrés sans pression à l’extérieur de la
structure du bâtiment (code de zone d’application « U »), repérés au niveau du marquage des produits
par la lettre « U »,
- pour les branchements et les collecteurs d’assainissement enterrés sans pression aussi bien à l’intérieur
de la structure du bâtiment (code de zone d’application « D ») qu’à l’extérieur de celle-ci (code de zone
d’application « U »), repérés au niveau du marquage des produits par les lettres « UD ».

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-U) - 2. del: Navodilo za ugotavljanje skladnosti

Ta tehnična specifikacija vsebuje navodila za ugotavljanje skladnosti spojin/formulacij, izdelkov in sestavov s standardom EN 1401-1. Uporablja se za tiste spojine/formulacije, izdelke in sestave, ki naj bi se vključili v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti in za vzpostavitev postopka certificiranja, ki ga izvajajo tretje osebe. Ta tehnična specifikacija se v povezavi s standardom EN 1401-1 (glejte Predgovor) uporablja za cevne sisteme iz nemehčanega polivinilklorida (PVC-U), ki se uporabljajo za: – sisteme za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo zunaj stavbe (koda območja uporabe »U«), kar je razvidno iz oznak »U« na izdelkih; – za sisteme za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo, za vkopane sisteme v stavbi (koda območja uporabe »D«) in zunaj stavbe (koda območja uporabe »U«), kar je razvidno iz oznak »UD« na izdelkih.

General Information

Status
Withdrawn
Publication Date
15-May-2012
Withdrawal Date
18-Feb-2020
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
19-Feb-2020

Relations

Buy Standard

Technical specification
TS CEN/TS 1401-2:2012
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2012
1DGRPHãþD
SIST ENV 1401-2:2001
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRGSDGQRYRGRLQNDQDOL]DFLMRNLGHOXMHMR
SRWHåQRVWQHPSULQFLSXLQVRSRORåHQLY]HPOMR1HPHKþDQSROLYLQLONORULG 39&8
GHO1DYRGLOR]DXJRWDYOMDQMHVNODGQRVWL
Plastics piping systems for non-pressure underground drainage and sewerage -
Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for assessment of
conformity
Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen -
Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung
der Konformität
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U)
- Partie 2 : Guide pour l'évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 1401-2:2012
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION
CEN/TS 1401-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
May 2012
ICS 23.040.01; 93.030 Supersedes ENV 1401-2:2000
English Version
Plastics piping systems for non-pressure underground drainage
and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part
2: Guidance for assessment of conformity
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte drucklose
branchements et les collecteurs d'assainissement enterrés Abwasserkanäle und -leitungen - Weichmacherfreies
sans pression - Poly(chlorure de vinyle) non plastifié (PVC- Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die
U) - Partie 2 : Guide pour l'évaluation de la conformité Beurteilung der Konformität
This Technical Specification (CEN/TS) was approved by CEN on 6 September 2011 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1401-2:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Introduction .4
1 Scope .6
2 Normative references .6
3 Terms and definitions .6
4 Abbreviated terms . 10
5 General . 10
6 Testing and inspection . 10
6.1 Material specification . 10
6.2 Grouping . 11
6.2.1 General . 11
6.2.2 Size groups . 11
6.2.3 Fitting groups . 12
6.3 Type testing . 12
6.4 Batch release tests . 15
6.5 Process verification tests . 17
6.6 Audit tests . 18
6.7 Indirect tests . 20
6.8 Test records . 20
Annex A (informative) Basic test matrix . 21
Bibliography . 22

Foreword
This document (CEN/TS 1401-2:2012) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes ENV 1401-2:2000.
Compared with ENV 1401-2:2000, the following changes have been made:
a) Use of the template drafted by CEN/TC 155/WG 21 for assessment of conformity documents (change of
"Terms and definitions" and addition of 1 column "Sampling procedures" in Tables);
b) Introduction of "Limits of addition of PVC reprocessed and recycled material" in a separate table (Table
2);
c) Addition of an informative Annex A: Basic test matrix.
EN 1401, Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized
poly(vinyl chloride) (PVC-U), consists of the following Parts:
 Part 1: Specifications for pipes, fittings and the system;
 Part 2: Guidance for the assessment of conformity.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organisation of
those tests used for the purpose of the assessment of conformity. This part of EN 1401 details the applicable
characteristics to be assessed as well as the frequency and sampling of testing for each type of test, i.e. type
testing (TT), batch release test (BRT), process verification test (PVT) and audit test (AT).
A typical scheme for the assessment of conformity of compounds/formulations, pipes, fittings, assemblies by
manufacturers is given in Figure 1.

Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of compounds/formulations, pipes, fittings, assemblies by
manufacturers, including a third-party certification, is given in Figure 2.

Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including a third-
party certification
1 Scope
This Technical Specification gives guidance for the assessment of conformity of compounds/formulations,
products and assemblies in accordance with EN 1401-1. It applies to those compounds/formulations, products
and assemblies intended to be included in the manufacturer’s quality plan as part of the quality management
system and for the establishment of third-party certification procedures.
NOTE 1 It is recommended that the quality management system conforms to or is no less stringent than the relevant
requirements of EN ISO 9001 [1].
NOTE 2 If third-party certification is involved, it is recommended that the certification body is accredited to either
EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3 In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1401-1 (see Foreword), this Technical Specification is applicable to piping systems
made of unplasticized poly(vinyl chloride) (PVC-U) used for the following puposes:
 for non pressure underground drainage and sewerage outside the building structure (application area
code "U"), reflected in the marking of products by "U";
 for non-pressure underground drainage and sewerage for both buried in ground within the building
structure (application area code "D") and outside the building structure (application area code "U"),
reflected in the marking of products by "UD".
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 1401-1:2009, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1401-1:2009 and the following apply.
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and responsibility
to carry out certification of conformity according to given rules of procedure and management
Note 1 to entry: A certification body is preferably accredited to EN 45011 [2].
3.2
inspection body
impartial organisation or company approved by the certification body as possessing the necessary
competence to verify and/or to carry out initial type testing, audit testing and inspection of the manufacturer's
factory production control in accordance with the relevant standard
Note 1 to entry: An inspection body is preferably accredited to EN ISO/IEC 17020 [5].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of
materials and products
Note 1 to entry: In the context of this part of EN 1401, the materials and products can be subjected to type testing,
batch release testing, process verification testing, audit testing and/or witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably accredited to EN ISO/IEC 17025 [6].
3.4
quality management system
management system to direct and control an organization with regard to quality
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [1].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to verify that the material, product, joint or assembly is capable of conforming to the
requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of compound/formulation or products, which
needs to be satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by or on behalf of the manufacturer on compound/formulation, products, joints or assemblies at
specific intervals to confirm that the process continues to be capable of producing products which conform to
the requirements given in the relevant standard
Note 1 to entry: Such tests are not required to release batches of compound/formulation or products; rather, they are
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.