EN ISO 7668:2018
(Main)Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees (ISO 7668:2018)
Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees (ISO 7668:2018)
ISO 7668:2018 specifies methods for the measurement of specular reflectance and specular gloss of flat samples of anodized aluminium using geometries of 20° (Method A), 45° (Method B), 60° (Method C) and 85° (Method D); and of specular reflectance by an additional 45° method (Method E) employing a narrow acceptance angle.
The methods described are intended mainly for use with clear anodized surfaces. They can be used with colour-anodized aluminium, but only with similar colours.
Anodisieren von Aluminium und Aluminiumlegierungen - Messung des gerichteten Reflexionsgrades und des Spiegelglanzes von anodisch erzeugten Oxidschichten bei Winkeln von 20°, 45°, 60° oder 85° (ISO 7668:2018)
Dieses Dokument legt Verfahren zur Messung des gerichteten Reflexionsgrades und des Spiegelglanzes von ebenen Proben aus anodisch oxidiertem Aluminium unter Anwendung der geometrischen Messbedingungen bei 20° (Verfahren A), 45° (Verfahren B), 60° (Verfahren C) und 85° (Verfahren D) sowie ein weiteres Verfahren zur Messung des gerichteten Reflexionsgrades bei 45° (Verfahren E) fest, bei dem ein kleiner Empfängerwinkel verwendet wird.
Die beschriebenen Verfahren sind hauptsächlich für farblos anodisierte Oberflächen vorgesehen. Sie können für farbig anodisiertes Aluminium verwendet werden, aber nur bei gleichen Farben.
Anodisation de l'aluminium et de ses alliages - Mesurage des caractéristiques de réflectivité et de brillant spéculaires des couches anodiques à angle fixe de 20 degrés, 45 degrés, 60 degrés ou 85 degrés (ISO 7668:2018)
L'ISO 7668:2018 spécifie des méthodes de mesure de la réflectivité spéculaire et du brillant spéculaire d'échantillons plats d'aluminium anodisé sous des angles de 20° (Méthode A), 45° (Méthode B), 60° (Méthode C) et 85° (Méthode D), plus une autre méthode à 45° (Méthode E) à petit angle d'ouverture pour le mesurage de la réflectivité spéculaire.
Les méthodes décrites sont principalement utilisables sur des surfaces plates anodisées claires. Elles peuvent être utilisées sur de l'aluminium anodisé coloré, mais dans ce cas, uniquement pour des couleurs semblables.
Anodizacija aluminija in aluminijevih zlitin - Merjenje odbojnosti in sijaja anodizirane plasti pod koti 20°, 45°, 60° ali 85° (ISO 7668:2018)
Ta dokument določa metode za merjenje refleksijske odbojnosti in refleksijskega sijaja ploskih vzorcev anodiziranega aluminija pod kotom 20° (metoda A), 45° (metoda B), 60° (metoda C)
in 85° (metoda D); in refleksijske odbojnosti z dodatno 45° metodo (metoda E), ki uporablja ozek sprejemni kot.
Opisane metode se povečini uporabljajo na čistih anodiziranih površinah. Lahko se uporabljajo z barvno-anodiziranim aluminijem, a le s podobnimi barvami.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7668:2018
01-maj-2018
1DGRPHãþD
SIST EN ISO 7668:2012
Anodizacija aluminija in aluminijevih zlitin - Merjenje odbojnosti in sijaja
anodizirane plasti pod koti 20°, 45°, 60° ali 85° (ISO 7668:2018)
Anodizing of aluminium and its alloys - Measurement of specular reflectance and
specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60
degrees or 85 degrees (ISO 7668:2018)
Anodisieren von Aluminium und Aluminiumlegierungen - Messung des gerichteten
Reflexionsgrades und des Spiegelglanzes von anodisch erzeugten Oxidschichten bei
Winkeln von 20°, 45°, 60° oder 85° (ISO 7668:2018)
Anodisation de l'aluminium et de ses alliages - Mesurage des caractéristiques de
réflectivité et de brillant spéculaires des couches anodiques à angle fixe de 20 degrés,
45 degrés, 60 degrés ou 85 degrés (ISO 7668:2018)
Ta slovenski standard je istoveten z: EN ISO 7668:2018
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
SIST EN ISO 7668:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 7668:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 7668:2018
EN ISO 7668
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2018
EUROPÄISCHE NORM
ICS 25.220.20 Supersedes EN ISO 7668:2010
English Version
Anodizing of aluminium and its alloys - Measurement of
specular reflectance and specular gloss of anodic oxidation
coatings at angles of 20 degrees, 45 degrees, 60 degrees or
85 degrees (ISO 7668:2018)
Anodisation de l'aluminium et de ses alliages - Anodisieren von Aluminium und
Mesurage des caractéristiques de réflectivité et de Aluminiumlegierungen - Messung des gerichteten
brillant spéculaires des couches anodiques à angle fixe Reflexionsgrades und des Spiegelglanzes von anodisch
de 20 degrés, 45 degrés, 60 degrés ou 85 degrés (ISO erzeugten Oxidschichten bei Winkeln von 20°, 45°, 60°
7668:2018) oder 85° (ISO 7668:2018)
This European Standard was approved by CEN on 14 March 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7668:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 7668:2018
EN ISO 7668:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 7668:2018
EN ISO 7668:2018 (E)
European foreword
This document (EN ISO 7668:2018) has been prepared by Technical Committee ISO/TC 79 "Light
metals and their alloys" in collaboration with Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2018, and conflicting national standards
shall be withdrawn at the latest by September 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 7668:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.