EN 13789:2002

Industrial valves - Cast iron globe valves

This European Standard specifies the requirements for cast iron globe valves in straight, angle or oblique pattern with flanged or threaded end connections. This standard applies to cast iron globe valves mainly used for industrial and general purpose applications. However they can be used for other applications provided the requirements of the relevant performance standards are met.

Industriearmaturen - Ventile aus Gusseisen

Diese Europäische Norm legt die Anforderungen fest für Ventile aus gußeisen in Durchgangsform, Eck- oder Schrägsitzform mit Flansch- oder Gewindeanschlüssen. Diese Norm ist anwendbar für Ventile aus Gußeisen, die vorwiegend für industrielle und allgemeine Anwendungen verwendet werden. Sie kann jedoch auch für andere Anwendungen verwendet werden, unter der Voraussetzung, daß die Anforderungen der dafür geltenden Gebrauchstauglichkeitsnormen erfüllt sind.

Robinetterie industrielle - Robinets à soupape en fonte

La présente Norme européenne spécifie les prescriptions des robinets à soupape en fonte, à tête droite, à tête inclinée ou à corps d'équerre, à extrémités à brides, ou filetées (voir EN 736-2).
La présente Norme européenne s'applique aux robinets à soupape en fonte utilisés principalement pour des applications à des fins industrielles et générales. Toutefois ils peuvent être utilisés pour d'autres applications sous réserve que les exigences des Normes appropriées de performance soient satisfaites.
La gamme des diamètres nominaux couverts est:
a)   extrémités à brides :
DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150 ;
DN 200; DN 250; DN 300; DN 350; DN 400.
b)   extrémités filetées :
½, ¾, 1, 1 ¼, 1 ½, 2.
La gamme des pressions nominales couvertes est :
a)   pour les appareils de robinetterie à extrémités à brides :
PN 6; PN 10; PN 16; PN 25; PN 40 ;
b)   pour les appareils de robinetterie à extrémités filetées :
PN 6; PN 10; PN 16.

Industrijski ventili - Litoželezni ventili

General Information

• Status: Withdrawn
• Publication Date: 22-Oct-2002
• Withdrawal Date: 04-May-2010
• ICS: 23.060.20 - Ball and plug valves
• Technical Committee: CEN/TC 69 - Industrial valves
• Drafting Committee: CEN/TC 69/WG 3 - Globe valves
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 05-May-2010
• Completion Date: 05-May-2010
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 13789:2003 - Industrial valves - Cast iron globe valves

Relations

• Replaced By: EN 13789:2010 - Industrial valves - Cast iron globe valves
• Effective Date: 12-May-2010

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Industrijski ventili - Litoželezni ventiliIndustriearmaturen - Ventile aus GusseisenRobinetterie industrielle - Robinets a soupape en fonteIndustrial valves - Cast iron globe valves23.060.10Zapirni ventili (kroglasti)Globe valvesICS:Ta slovenski standard je istoveten z:EN 13789:2002SIST EN 13789:2003en01-julij-2003SIST EN 13789:2003SLOVENSKI
STANDARD



SIST EN 13789:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13789October 2002ICS 23.060.20English versionIndustrial valves - Cast iron globe valvesRobinetterie industrielle - Robinets à soupape en fonteIndustriearmaturen - Ventile aus GusseisenThis European Standard was approved by CEN on 9 September 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13789:2002 ESIST EN 13789:2003



EN 13789:2002 (E)2ContentsForeword.31Scope.42Normative references.43Terms and definitions.54Requirements.54.1Design.54.2Functional characteristics.85Test procedures.96Declaration of compliance.97Designation.98Marking and preparation for storage and transportation.98.1Marking.98.2Preparation for storage and transportation.10Annex A (informative)
Information to be supplied by the purchaser.11Annex B (normative)
Comparison between EN and ISO cast iron material grades.12Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of EU Directives.13SIST EN 13789:2003



EN 13789:2002 (E)3ForewordThis document (EN 13789:2002) has been prepared by Technical Committee CEN /TC 69, "Industrial valves", thesecretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by April 2003, and conflicting national standards shall be withdrawn at the latest byApril 2003.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.In this European Standard the Annex A is informative and Annex B is normative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 13789:2003



EN 13789:2002 (E)41 ScopeThis European Standard specifies the requirements for cast iron globe valves in straight, angle or oblique pattern(see EN 736-2) with flanged or threaded end connections.This standard is applicable to cast iron globe valves mainly used for industrial and general purpose applications.However, they can be used for other applications provided the requirements of the relevant performance standardsare met.The range of nominal sizes covered is:a) flanged:DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200;DN 250; DN 300; DN 350; DN 400.b) threaded:½, ¾, 1, 1¼, 1½, 2.The range of pressure designations covered is:a) for flanged end valves:PN 6; PN 10; PN 16; PN 25; PN 40;b) for threaded end valves:PN 6; PN 10; PN 16.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications.
Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter.
Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision.
For undated references the latest edition of thepublication referred to applies (including amendments).EN 19, Industrial Valves - Marking of metallic valves.EN 545:2002, Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and testmethodsEN 558-1, Industrial valves – Face-to-face and centre-to-facedimensions of metal valves for use in flanged pipesystems - Part 1 : PN-designated valves.EN 736-1, Valves - Terminology - Part 1 : Definition of types of valves.EN 736-2, Valves - Terminology - Part 2 : Definition of components of valves.EN 736-3, Valves - Terminology - Part 3 : Definition of terms.EN 1092-2:1997, Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PNdesignated - Part 2 : Cast iron flanges.EN 1561:1997, Founding - Grey cast irons.EN 1562:1997, Founding - Malleable cast irons.SIST EN 13789:2003



EN 13789:2002 (E)5EN 1563:1997, Founding - Spheroidal graphite cast irons.prEN 12266-1, Industrial valves - Testing of valves - Part 1 : Pressure tests, test procedures and acceptancecriteria – Mandatory requirements.EN 12266-2, Industrial valves - Testing of valves - Part 2 : Tests, test procedures and acceptance criteria –Supplementary requirements.EN 12351, Industrial valves - Protective caps for valves with flanged connections.EN 12516-3, Valves - Shell design strength – Part 3 : Experimental method.EN 12570, Industrial valves - Method for sizing the operating element.EN ISO 5210, Industrial valves - Multi-turn valve actuator attachments (ISO 5210:1991).ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads - Part 1 : Dimensions, tolerancesand designation.ISO 185:1988, Grey cast iron – Classification.ISO 1083:1987, Spheroidal graphite cast iron – Classificaton.ISO 5922:1981, Malleable cast iron.3 Terms and definitionsFor the purposes of this European Standard the terms and definitions of types of valves and components and thedefinitions of terms given in EN 736-1, EN 736-2 and EN-736-3 apply.NOTEThe terms maximum allowable pressure, PS, and test pressure, PT, defined in EU Directive 97/23/EC (PED) areequivalent to the terms allowable pressure, ps, and test pressure, pt, defined in EN 736-3.4 Requirements4.1 Design4.1.1 Materials4.1.1.1The body and bonnet materials shall be selected from Table 1.
The limits of use given in the materialstandard shall be taken into account.For PN 40 rated valves, spheroidal graphite cast iron only shall be used.SIST EN 13789:2003



EN 13789:2002 (E)6Table 1 — Body and bonnet materialsDesignationGraphite StructureENRmN/mm2GradeNumber1561:1997200 aEN-GJL-200EN-JL1030Grey cast iron1561:1997250EN-GJL-250EN-JL10401563:19971563:19971563:19971563:19971563:19971563:19971563:1997350350400400400500600EN-GJS-350-22-LTEN-GJS-350-22-RTEN-GJS-400-18-LTEN-GJS-400-18-RTEN-GJS-400-15EN-GJS-500-7EN-GJS-600-3EN-JS1015EN-JS1014EN-JS1025EN-JS1024EN-JS1030EN-JS1050EN-JS1060Spheroidal graphitecast iron545:2002420-5EN-545-420-5-Malleable cast iron1562:19971562:1997300350EN-GJMB-300-6EN-GJMB-350-10EN-JM1110EN-JM1130aGrade 200 shall not be used for valves with PN 25 flanged end connections.4.1.1.2The manufacturer shall declare the materials of construction and any coatings of components incontact with the line fluid from which the suitability of the valve for the application can be determined.4.1.1.3Welding of grey cast iron and impregnation of castings of all materials is not permitted.4.1.2 Pressure/temperature ratings4.1.2.1The pressure/temperature ratings shall be in accordance with EN 1092-2 for the equivalentISO material grade.Annex B shall be used to determine the equivalent ISO material grade for the EN material grades specified inTable 1.4.1.2.2Any restrictions of temperature and/or pressure below those specified in EN 1092-
...