prEN ISO 21009-2

Cryogenic vessels - Static vacuum insulated vessels - Part 2: Operational requirements (ISO/DIS 21009-2:2023)

ISO 21009-2:2015 specifies operational requirements for static vacuum insulated vessels designed for a maximum allowable pressure of more than 50 kPa (0,5 bar). It may also be used as a guideline for vessels designed for a maximum allowable pressure of less than 50 kPa (0,5 bar).
ISO 21009-2:2015 applies to vessels designed for cryogenic fluids specified in ISO 21009‑1.
Static cryogenic vessels are often partly equipped by the manufacturer, but may be installed or re-installed by another party, such as the operator, user or owner.
NOTE 1       For the installation of these vessels, additional requirements can apply; these are defined in specific regulations.
NOTE 2       Some requirements of this standard can be covered by local regulations, e.g. safety distances, occupational safety and health. Where there is a conflict between the requirements of this International Standard and any applicable local regulation, the local regulation always takes precedence.

Kryo-Behälter - Ortsfeste vakuumisolierte Behälter - Teil 2: Betriebsanforderungen (ISO/DIS 21009‑2:2023)

Récipients cryogéniques - Récipients fixes isolés sous vide - Partie 2: Exigences de fonctionnement (ISO/DIS 21009-2:2023)

ISO 21009-2:2015 spécifie les exigences de fonctionnement pour les récipients cryogéniques fixes isolés sous vide, conçus pour une pression maximale admissible supérieure à 50 kPa (0,5 bar). Elle peut également être utilisée comme guide pour les récipients conçus pour une pression maximale admissible inférieure à 50 kPa (0,5 bar).
ISO 21009-2:2015 s'applique à des récipients conçus pour des fluides cryogéniques tels que spécifiés dans l'ISO 21009‑1.
Les récipients cryogéniques fixes sont souvent partiellement équipés par le fabricant, mais ils peuvent être installés ou réinstallés par une autre partie, comme par exemple l'opérateur, l'utilisateur ou le propriétaire.
NOTE 1       Pour l'installation des récipients en question, des exigences supplémentaires peuvent s'appliquer ; elles sont définies dans des réglementations spécifiques.
NOTE 2       Un certain nombre d'exigences relatives à la présente norme peut être traité par les réglementations locales, par exemple, distances de sécurité, sécurité et santé au travail. En cas de conflit entre la présente Norme internationale et toute réglementation locale applicable, la réglementation locale prévaut toujours.

Kriogene posode - Stabilne, vakuumsko izolirane posode - 2. del: Zahteve za obratovanje (ISO/DIS 21009-2:2023)

General Information

• Status: Not Published
• Publication Date: 06-Jan-2025
• ICS: 23.020.40 - Cryogenic vessels
• Technical Committee: CEN/TC 268 - Cryogenic vessels
• Drafting Committee: CEN/TC 268/WG 3 - Operational requirements
• Current Stage: 4060 - Closure of enquiry - Enquiry
• Start Date: 04-Sep-2023
• Completion Date: 04-Sep-2023
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: oSIST prEN ISO 21009-2:2023 - Cryogenic vessels - Static vacuum insulated vessels - Part 2: Operational requirements (ISO/DIS 21009-2:2023)

Relations

• Revises: EN ISO 21009-2:2015 - Cryogenic vessels - Static vacuum insulated vessels - Part 2: Operational requirements (ISO 21009-2:2015)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 21009-2:2023
01-september-2023
Kriogene posode - Stabilne, vakuumsko izolirane posode - 2. del: Zahteve za
obratovanje (ISO/DIS 21009-2:2023)
Cryogenic vessels - Static vacuum insulated vessels - Part 2: Operational requirements
(ISO/DIS 21009-2:2023)
Kryo-Behälter - Ortsfeste vakuumisolierte Behälter - Teil 2: Betriebsanforderungen
(ISO/DIS 21009-2:2023)
Récipients cryogéniques - Récipients fixes isolés sous vide - Partie 2: Exigences de
fonctionnement (ISO/DIS 21009-2:2023)
Ta slovenski standard je istoveten z: prEN ISO 21009-2
ICS:
23.020.40 Proti mrazu odporne posode Cryogenic vessels
(kriogenske posode)
oSIST prEN ISO 21009-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 21009-2:2023

---------------------- Page: 2 ----------------------
oSIST prEN ISO 21009-2:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 21009-2
ISO/TC 220 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2023-06-12 2023-09-04
Cryogenic vessels — Static vacuum insulated vessels —
Part 2:
Operational requirements
Récipients cryogéniques — Récipients fixes isolés sous vide —
Partie 2: Exigences de fonctionnement
ICS: 23.020.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 21009-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 3 ----------------------
oSIST prEN ISO 21009-2:2023

DRAFT INTERNATIONAL STANDARD
ISO/DIS 21009-2
ISO/TC 220 Secretariat: AFNOR
Voting begins on: Voting terminates on:

Cryogenic vessels — Static vacuum insulated vessels —
Part 2:
Operational requirements
Récipients cryogéniques — Récipients fixes isolés sous vide —
Partie 2: Exigences de fonctionnement
ICS: 23.020.40
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 21009-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
  © ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 4 ----------------------
oSIST prEN ISO 21009-2:2023
ISO/DIS 21009-2:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions .
...