EN 13480-2:2017/A8:2021
(Amendment)Metallic industrial piping - Part 2: Materials
Metallic industrial piping - Part 2: Materials
This document specifies the requirements for steel products used for industrial piping and supports.
For some metallic materials other than steel, such as spheroidal graphite cast iron, aluminium, nickel, copper, titanium, requirements are or will be formulated in separate parts of this document.
For metallic materials which are not covered by a harmonized material standard and are not likely to be in near future, specific rules are given in this part or the above cited parts of this document.
Metallische industrielle Rohrleitungen - Teil 2: Werkstoffe
Tuyauteries industrielles métalliques - Partie 2: Matériaux
Kovinski industrijski cevovodi - 2. del: Materiali - Dopolnilo A8
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2021
Kovinski industrijski cevovodi - 2. del: Materiali - Dopolnilo A8
Metallic industrial piping - Part 2: Materials
Metallische industrielle Rohrleitungen - Teil 2: Werkstoffe
Tuyauteries industrielles métalliques - Partie 2: Matériaux
Ta slovenski standard je istoveten z: EN 13480-2:2017/A8:2021
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13480-2:2017/A8
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2021
EUROPÄISCHE NORM
ICS 23.040.01
English Version
Metallic industrial piping - Part 2: Materials
Tuyauteries industrielles métalliques - Partie 2: Metallische industrielle Rohrleitungen - Teil 2:
Matériaux Werkstoffe
This amendment A8 modifies the European Standard 2659471; it was approved by CEN on 16 August 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-2:2017/A8:2021 E
worldwide for CEN national Members.
Contents
European foreword . 3
1 Modification to 3.1.2, temperature adjustment term T . 4
S
2 Modification to 3.1.3, design reference temperature T . 4
R
3 Modification to 3.2, Symbols and units . 4
4 Modification to Clause 4, Requirements for materials to be used for pressure
containing parts in industrial piping . 5
5 Modification to Annex A, Grouping system for steels for pressure equipment . 6
6 Modification to B.1, General . 8
7 Modification to B.2.2.1, General . 8
8 Modification to B.2.2.6, Temperature adjustment . 8
European foreword
This document (EN 13480-2:2017/A8:2021) has been prepared by Technical Committee CEN/TC 267
“Industrial piping and pipelines”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of EN 13480-2:2017.
This document includes the text of the amendment itself. The amended/corrected pages of
EN 13480-2:2017 will be published in the new Edition 2022 of the European Standard.
Amendments EN 13480-2:2017/prA4 to EN 13480-2:2017/prA6 are withdrawn from the work program
of Technical Committee CEN/TC 267 “Industrial piping and pipelines” following CEN Rules related to the
time limit for activating Preliminary Work Items.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
1 Modification to 3.1.2, temperature adjustment term T
S
Replace “T ” by “T ”. Definition 3.1.2 shall read as follows:
S A
“3.1.2
temperature adjustment term
T
A
temperature relevant to the calculation of the design reference temperature T and dependent on the
R
calculated tensile membrane stress at the appropriate minimum metal temperature
Note 1 to entry Values for temperature adjustment term T are given in Table B.2–12.
A
Note 2 to entry For tensile membrane stress reference is made to EN 13480-3:2017, Clause 12.”.
2 Modification to 3.1.3, design reference temperature T
R
Replace “T ” by “T ”. Definition 3.1.3 shall read as follows:
S A
“3.1.3
design reference temperature
T
R
temperature used for determin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.