EN 474-9:2006
(Main)Earth-moving machinery - Safety - Part 9: Requirements for pipelayers
Earth-moving machinery - Safety - Part 9: Requirements for pipelayers
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to pipelayers as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This part gives additional requirements for rear mounted winch.
The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006.
This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for pipelayers.
This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of pipelayers.
This part specifies additional requirements for rear mounted winches.
Pipelayers with rotating upper structure are excluded from the scope of this document. However, specific requirements are under development.
This European Standard is not applicable to pipelayers manufactured before the date of publication of this European Standard by CEN.
Erdbaumaschinen - Sicherheit - Teil 9: Anforderungen für Rohrverleger
Dieser Teil der EN 474 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die für Rohrverleger zutreffen, wie sie in EN ISO 6165:2002 definiert sind, wenn sie bestimmungsgemäß verwendet werden. Die nach vernünftigem Ermessen für den Hersteller vorhersehbare Nutzung der Maschine außerhalb der bestimmungsgemäßen Verwendung ist ebenfalls berücksichtigt (siehe
Abschnitt 4).
Die Anforderungen gelten ergänzend zu den allgemeinen Anforderungen der EN 474-1:2006.
Dieser Teil wiederholt nicht die Anforderungen der EN 474-1:2006, aber ergänzt oder ersetzt diese, sofern sie für den Einsatz von Rohrverlegern von Bedeutung sind.
Dieser Teil beschreibt die geeigneten technischen Maßnahmen, die erforderlich sind, die Risiken, die aufgrund signifikanter Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die während der Inbetriebnahme, des Betriebs, der Instandhaltung von Rohrverlegern eintreten können, zu mindern oder zu beseitigen.
Dieser Teil gibt zusätzliche Anforderungen für die heckseitig montierte Winde.
Rohrverleger mit drehbarem Aufbau sind vom Umfang dieses Dokuments ausgenommen. Spezifische Anforderungen sind in Ausarbeitung.
Diese Europäische Norm ist nicht anzuwenden für Rohrverleger, die vor der Veröffentlichung dieser Europäischen Norm durch CEN hergestellt wurden.
Engins de terassement - Sécurité - Partie 9: Prescriptions applicables aux poseurs de canalisations
La présente partie du prEN 474 traite de tous les phénomènes, situations et événements dangereux significatifs relatifs aux poseurs de canalisations définis dans l’EN ISO 6165:2002, lorsqu’ils sont utilisés comme prévu ou dans des conditions de mauvais usage que le fabricant peut raisonnablement prévoir (voir l’Article 4). La présente partie donne également des prescriptions relatives aux treuils montés à l’arrière.
Les prescriptions figurant dans la présente partie viennent en complément des prescriptions communes présentées dans la partie 1.
La présente partie ne répète pas les prescriptions de la partie 1 mais en ajoute ou en remplace certaines applicables aux poseurs de canalisations.
La présente partie prescrit les mesures techniques appropriées pour éliminer ou réduire les risques dus aux phénomènes, situations et événements dangereux significatifs survenant lors de la mise en service, du fonctionnement et de la maintenance des poseurs de canalisations.
Les poseurs de canalisations comportant une structure supérieure pivotante sont exclus du présent document. Cependant, des prescriptions spécifiques sont en cours de développement.
La présente Norme européenne n’est pas applicable aux poseurs de canalisations fabriqués après la publication de la présente Norme européenne par le CEN.
Stroji za zemeljska dela - Varnost - 9. del: Zahteve za stroje za polaganje cevi
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Earth-moving machinery - Safety - Part 9: Requirements for pipelayersStroji za zemeljska dela - Varnost - 9. del: Zahteve za stroje za polaganje ceviEngins de terassement - Sécurité - Partie 9: Prescriptions applicables aux poseurs de canalisationsErdbaumaschinen - Sicherheit - Teil 9: Anforderungen für RohrverlegerTa slovenski standard je istoveten z:EN 474-9:2006SIST EN 474-9:2007en53.100Stroji za zemeljska delaEarth-moving machineryICS:SIST EN 474-9:2000/AC:2001SIST EN 474-9:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 474-9:200701-maj-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 474-9November 2006ICS 53.100Supersedes EN 474-9:1998
English VersionEarth-moving machinery - Safety - Part 9: Requirements forpipelayersEngins de terassement - Sécurité - Partie 9: Prescriptionsapplicables aux poseurs de canalisationsErdbaumaschinen - Sicherheit - Teil 9: Anforderungen fürRohrverlegerThis European Standard was approved by CEN on 17 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 474-9:2006: E
List of additional significant hazards – Pipelayers.10 Annex B (informative)
Illustrations.11 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC.13 Bibliography.14
Figures Figure B.1 — Crawler pipelayer.11 Figure B.2 — Wheel pipelayer.11 Figure B.3 — Pipelayer side view.12 Figure B.4 — Crawler pipelayer with a rotating upper structure.12
Tables Table A.1 — List of additional significant hazards.10
The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006. This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for pipelayers. This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of pipelayers. This part specifies additional requirements for rear mounted winches. Pipelayers with rotating upper structure are excluded from the scope of this document. However, specific requirements are under development. This European Standard is not applicable to pipelayers manufactured before the date of publication of this European Standard by CEN. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 474-1:2006, Earth-moving machinery — Safety — Part 1: General requirements EN 1032:2003, Mechanical vibration — Testing of mobile machinery in order to determine the vibration emission value EN 1677-1:2000, Components for slings — Safety — Part 1: Forged steel components, Grade 8 EN 1677-2:2000, Components for slings — Safety — Part 2: Forged steel lifting hooks with latch, Grade 8 EN ISO 3411:1999, Earth-moving machinery — Human physical dimensions of operators and minimum operator space envelope (ISO 3411:1995) EN ISO 7096:2000, Earth-moving machinery — Laboratory evaluation of operator seat vibra
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.