prEN 54-4

Fire detection and fire alarm systems - Part 4: Power supply equipment

This European Standard specifies product characteristics, methods of test and assessment and performance criteria for power supply equipment (PSE) of fire detection and fire alarm systems installed in and around buildings (Function L of Figure 1 of EN 54-1:2011).
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of power supply equipment (PSE) to this EN.

Brandmeldeanlagen - Teil 4: Energieversorgungseinrichtungen

Systèmes de détection et d’alarme incendie - Partie 4: Equipement d’alimentation électrique

Sistemi za odkrivanje in javljanje požara ter alarmiranje - 4. del: Oprema za napajanje

General Information

• Status: Not Published
• Publication Date: 27-Apr-2017
• ICS: 13.220.20 - Fire protection
• Technical Committee: CEN/TC 72 - Fire detection and fire alarm systems
• Drafting Committee: CEN/TC 72/WG 8 - Power supply equipment
• Current Stage: 4098 - Decision to abandon - Enquiry
• Completion Date: 16-Nov-2016
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Mandate: M/109 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on fire alarm/detection, fixed firefighting, fire and smoke control and explosion suppression products
• Ref Project: oSIST prEN 54-4:2015 - Fire detection and fire alarm systems - Part 4: Power supply equipment

Relations

• Revises: EN 54-4:1997 - Fire detection and fire alarm systems - Part 4: Power supply equipment
• Effective Date: 18-Sep-2013

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2015
Sistemi za odkrivanje in javljanje požara ter alarmiranje - 4. del: Oprema za
napajanje
Fire detection and fire alarm systems - Part 4: Power supply equipment
Brandmeldeanlagen - Teil 4: Energieversorgungseinrichtungen
Systèmes de détection et d’alarme incendie - Partie 4: Equipement d’alimentation
électrique
Ta slovenski standard je istoveten z: prEN 54-4
ICS:
13.220.20 3RåDUQD]DãþLWD Fire protection
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2015
ICS 13.220.20 Will supersede EN 54-4:1997
English Version
Fire detection and fire alarm systems - Part 4: Power
supply equipment
Systèmes de détection et d'alarme incendie - Partie 4: Brandmeldeanlagen - Teil 4:
Equipement d'alimentation électrique Energieversorgungseinrichtungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 72.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 54-4:2015 E
worldwide for CEN national Members.

Contents
European foreword . 5
Introduction . 7
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and abbreviations . 8
4 Product characteristics . 10
4.1 Compliance . 10
4.2 Operational reliability . 10
4.2.1 General product characteristics . 10
4.2.2 Product characteristics for non-integrated PSE . 12
4.2.3 Product characteristics for integrated PSE with external outputs . 12
4.2.4 Product characteristics for integrated PSE without external outputs . 13
4.2.5 Product characteristics for distributed PSE . 13
4.2.6 Product characteristics for PSE controlled by software and related
technology . 14
4.3 Durability of operational reliability, environmental . 16
4.3.1 Cold (operational) . 16
4.3.2 Damp heat, steady-state (operational) . 16
4.3.3 Vibration, sinusoidal (operational) . 16
4.4 Durability of operational reliability, EMC immunity . 17
4.4.1 Mains supply voltage dips and short interruptions . 17
4.4.2 Electrostatic discharge . 17
4.4.3 Radiated electromagnetic fields . 17
4.4.4 Conducted disturbances induced by electromagnetic fields . 17
4.4.5 Fast transient bursts . 17
4.4.6 Slow high energy voltage surges . 17
5 Testing, assessment and sampling methods . 17
5.1 Compliance . 17
5.1.1 Provision of equipment and supporting information and tools . 17
5.1.2 Equipment configuration . 18
5.1.3 Atmospheric conditions for testing . 18
5.1.4 Tolerances . 18
5.1.5 Full functional test and design assessments for operational reliability . 18
5.1.6 Reduced functional test . 19
5.1.7 Final functional test . 19
5.1.8 Test schedule for the tests of 5.3 and 5.4 . 20
5.2 Operational reliability . 20
5.2.1 General product characteristics . 20
5.2.2 Product characteristics for non-integrated PSE . 22
5.2.3 Product characteristics for integrated PSE with external outputs . 23
5.2.4 Product characteristics for integrated PSE without external outputs . 23
5.2.5 Product characteristics for distributed PSE . 24
5.2.6 Requirements for PSE controlled by software and related technology . 24
5.3 Durability of operational reliability, environmental . 26
5.3.1 Cold (operational) . 26
5.3.2 Damp heat, steady-state (operational) . 27
5.3.3 Vibration, sinusoidal (operational) . 27
5.4 Durability of operational reliability, EMC immunity . 28
5.4.1 Mains supply voltage dips and short interruptions . 28
5.4.2 Electrostatic discharge . 29
5.4.3 Radiated electromagnetic fields . 29
5.4.4 Conducted disturbances induced by electromagnetic fields . 30
5.4.5 Fast transient bursts . 31
5.4.6 Slow high energy voltage surges . 31
6 Assessment and verification of constancy of performance (AVCP) . 32
6.1 General . 32
6.2 Type testing . 32
6.2.1 General . 32
6.2.2 Test samples, testing and compliance criteria . 33
6.2.3 Test reports . 33
6.3 Factory production control (FPC) . 34
6.3.1 General . 34
6.3.2 Requirements . 34
6.3.3 Product specific requirements . 36
6.3.4 Initial inspection of factory and FPC . 37
6.3.5 Continuous surveillance of FPC . 38
6.3.6 Procedure for modifications . 38
6.3.7 One-off products, pre-production products, (e.g. prototypes) and products
produced in very low quantities . 38
7 Classification and designation . 39
8 Marking, labelling and packaging . 39
Annex A (normative) Documentation and manufacturer's declarations. 40
A.1 General requirements and manufacturer's declarations . 40
A.2 Installation and user documentation . 40
A.3 Design documentation . 41
A.4 Software design documentation . 41
Annex B (normative) PSE loading and charger tests . 43
B.1 General . 43
B.2 Test procedures . 43
B.2.1 General .
...