EN 12166:2011
(Main)Copper and copper alloys - Wire for general purposes
Copper and copper alloys - Wire for general purposes
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding, intended for general purposes, spring and fastener manufacturing applications.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
Kupfer und Kupferlegierungen - Drähte zur allgemeinen Verwendung
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenz-abmaße für durch Ziehen, Walzen oder Pressen endgefertigte Drähte aus Kupferlegierungen zur allgemeinen Verwendung und zur Herstellung von Federn und Verbindungselementen fest. Der Ablauf der Probenentnahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Europäischen Norm sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Fils pour usages généraux
La présente Norme européenne spécifie la composition, les caractéristiques et les tolérances dimensionnelles des fils en alliages de cuivre fabriqués par étirage, laminage ou filage, destinés à des usages généraux et à la fabrication de ressorts et d'éléments de fixation.
Les procédures d'échantillonnage et les méthodes d'essai pour la vérification de la conformité aux prescriptions de la présente Norme européenne sont également spécifiées.
Baker in bakrove zlitine - Žica za splošno uporabo
Dokument določa sestavo, zahteve za lastnosti in odstopke mer za palice iz bakra in bakrovih zlitin za splošno uporabo in aplikacije za izdelavo vzmeti in sponk. Določeni so tudi postopki vzorčenja in metode preskušanja za preverjanje skladnosti z zahtevami tega dokumenta.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Žica za splošno uporaboKupfer und Kupferlegierungen - Drähte zur allgemeinen VerwendungCuivre et alliages de cuivre - Fils pour usages générauxCopper and copper alloys - Wire for general purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 12166:2011SIST EN 12166:2011en,fr,de01-oktober-2011SIST EN 12166:2011SLOVENSKI
STANDARDSIST EN 12166:1999/AC:2004SIST EN 12166:19991DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12166
June 2011 ICS 77.150.30 Supersedes EN 12166:1998English Version
Copper and copper alloys - Wire for general purposes
Cuivre et alliages de cuivre - Fils pour usages généraux
Kupfer und Kupferlegierungen - Drähte zur allgemeinen Verwendung This European Standard was approved by CEN on 14 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12166:2011: ESIST EN 12166:2011
Position of wire cross-section within a coil, reel, spool or drum . 30Bibliography . 32 SIST EN 12166:2011
Tables Table 1 — Composition of low alloyed copper alloys . 15 Table 2 — Composition of copper-nickel-zinc alloys . 16 Table 3 — Composition of copper-tin alloys . 16 Table 4 — Composition of copper-zinc alloys. 17 Table 5 — Composition of copper-zinc-lead alloys . 18 Table 6 — Composition of complex copper-zinc alloys . 18 Table 7 — Mechanical properties of wire of low alloyed copper alloys . 19 Table 8 — Mechanical properties of wire of copper-nickel-zinc alloys . 21 Table 9 — Mechanical properties of wire of copper-tin alloys . 22 Table 10 — Mechanical properties of wire of copper-zinc alloys . 23 Table 11 — Mechanical properties of wire of copper-zinc-lead alloys . 25 Table 12 — Mechanical properties of wire of complex copper-zinc alloys . 26 Table 13 — Grain size designations . 26 Table 14 — Tolerances on diameter of round wire . 27 Table 15 — Tolerances on width across-flats of square or regular polygonal wire . 27 Table 16 — Tolerances on width and thickness of rectangular wire . 28 Table 17 — Corner radii for square or rectangular wire . 28 Table 18 — Sampling rate . 29
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.