EN ISO 5395-1:2013/A1:2018
(Amendment)Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 1: Terminology and common tests - Amendment 1: Annex G (Vibration test code - Hand-arm vibration and whole-body vibration) (ISO 5395-1:2013/Amd 1:2017)
Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 1: Terminology and common tests - Amendment 1: Annex G (Vibration test code - Hand-arm vibration and whole-body vibration) (ISO 5395-1:2013/Amd 1:2017)
Gartengeräte - Sicherheitsanforderungen für verbrennungsmotorisch angetriebene Rasenmäher - Teil 1: Begriffe und allgemeine Prüfverfahren - Änderung 1: Anhang G (Schwingungsmessverfahren - Hand-Arm Schwingungen und Ganzkörper-Schwingungen) (ISO 5395-1:2013/Amd.1:2018)
Matériel de jardinage - Exigences de sécurité pour les tondeuses à gazon à moteur à combustion interne - Partie 1: Terminologie et essais communs - Amendement 1: Annexe G (Code d'essai de vibration - Vibrations main-bras et vibrations transmises à l'ensemble du corps) (ISO 5395-1:2013/Amd 1:2017)
Oprema za nego vrta - Varnostne zahteve za motorne vrtne kosilnice - 1. del: Terminologija in splošni preskusi - Dopolnilo A1: Dodatek G (Preskušanje vibracij - Vibracije v rokah in celotnem telesu) (ISO 5395-1:2013/Amd 1:2017)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2018
Oprema za nego vrta - Varnostne zahteve za motorne vrtne kosilnice - 1. del:
Terminologija in splošni preskusi - Dopolnilo A1: Dodatek G (Preskušanje vibracij
- Vibracije v rokah in celotnem telesu) (ISO 5395-1:2013/Amd 1:2017)
Garden equipment - Safety requirements for combustion-engine-powered lawnmowers -
Part 1: Terminology and common tests - Amendment 1: Annex G (Vibration test code -
Hand-arm vibration and Whole-body vibration) (ISO 5395-1:2013/Amd 1:2017)
Gartengeräte - Sicherheitsanforderungen für verbrennungsmotorisch angetriebene
Rasenmäher - Teil 1: Begriffe und allgemeine Prüfverfahren - Änderung 1: Anhang G
(Schwingungsmessverfahren - Hand-Arm-Schwingungen und Ganzkörper-
Schwingungen) (ISO 5395-1:2013/Amd 1:2017)
Matériel de jardinage - Exigences de sécurité pour les tondeuses à gazon à moteur à
combustion interne - Partie 1: Terminologie et essais communs - Amendement 1:
Annexe G (Code d'essai de vibration - Vibrations main-bras et vibrations transmises à
l'ensemble du corps) (ISO 5395-1:2013/Amd 1:2017)
Ta slovenski standard je istoveten z: EN ISO 5395-1:2013/A1:2018
ICS:
65.060.70 Vrtnarska oprema Horticultural equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 5395-1:2013/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2018
EUROPÄISCHE NORM
ICS 65.060.70
English Version
Garden equipment - Safety requirements for combustion-
engine-powered lawnmowers - Part 1: Terminology and
common tests - Amendment 1: Annex G (Vibration test
code - Hand-arm vibration and whole-body vibration) (ISO
5395-1:2013/Amd 1:2017)
Matériel de jardinage - Exigences de sécurité pour les Gartengeräte - Sicherheitsanforderungen für
tondeuses à gazon à moteur à combustion interne - verbrennungsmotorisch angetriebene Rasenmäher -
Partie 1: Terminologie et essais communs - Teil 1: Begriffe und allgemeine Prüfverfahren -
Amendement 1: Annexe G (Code d'essai de vibration - Änderung 1: Anhang G (Schwingungsmessverfahren -
Vibrations main-bras et vibrations transmises à Hand-Arm-Schwingungen und Ganzkörper-
l'ensemble du corps) (ISO 5395-1:2013/Amd 1:2017) Schwingungen) (ISO 5395-1:2013/Amd 1:2017)
This amendment A1 modifies the European Standard EN ISO 5395-1:2013; it was approved by CEN on 11 December 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5395-1:2013/A1:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4
European foreword
This document (EN ISO 5395-1:2013/A1:2018) has been prepared by Technical Committee ISO/TC 23
“Tractors and machinery for agriculture and forestry” in collaboration with Technical Committee
CEN/TC 144 “Tractors and machinery for agriculture and forestry” the secretariat of which is held by
AFNOR.
This Amendment to the European Standard EN ISO 5395-1:2013 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by November 2018,
and conflicting national standards shall be withdrawn at the latest by November 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5395-1:2013/Amd 1:2017 has been approved by CEN as EN ISO 5395-1:2013/A1:2018
without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request "M/396
Mandate to CEN and CENELEC for Standardization in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
Essential Requirements of Clause(s)/sub-clause(s) of this Remarks/Notes
Directive 2006/42/EC EN
Within the limits of the scope All normative clauses The main function of
all relevant essential EN ISO 5395-1 is to provide test
requirements are covered procedures for the verification of
the requirements of
EN ISO 5395-2 or EN ISO 5395-3,
as appropriate.
Compliance with EN ISO 5395-1
together with either
EN ISO 5395-2 or EN ISO 5395-3,
as appropriate, is necessary to
achieve presumption of
conformity with the relevant
essential requirements of
Directive 2006/42/EC.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 5395-1
Second edition
2013-09-01
AMENDMENT 1
2017-12
Garden equipment — Safety
requirements for combustion-engine-
powered lawnmowers —
Part 1:
Terminology and common tests
AMENDMENT 1: Annex G (Vibration test
code — Hand-arm vibration and whole-
body vibration)
Matériel de jardinage — Exigences de sécurité pour les tondeuses à
gazon à moteur à combustion interne —
Partie 1: Terminologie et essais communs
AMENDEMENT 1: Annexe G (Code d'essai de vibration — Vibrations
main-bras et vibrations transmises à l'ensemble du corps)
Reference number
ISO 5395-1:2013/Amd.1:2017(E)
©
ISO 2017
ISO 5395-1:2013/Amd.1:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 5395-1:2013/Amd.1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 23 Tractors and machinery for agriculture
and forestry, Subcommittee SC 13 Powered lawn and garden equipment.
ISO 5395-1:2013/Amd.1:2017(E)
Garden equipment — Safety requirements for combustion-
engine-powered lawnmowers —
Part 1:
Terminology and common tests
AMENDMENT 1: Annex G (Vibration test code — Hand-arm
vibration and whole-body vibration)
Normative references
Add the following references.
ISO 5349-1, Mechanical vibration — Measurement and evaluation of human exposure to hand-transmitted
vibration — Part 1: General requirements
ISO 8041, Human response to vibration — Measuring instrumentation
Annex G
Replace Annex G with the following. Note that G.1 has not been revised, but has been kept here for
context.
G.1 General
This annex specifies a vibration test code for determining, efficiently and under specified conditions,
the magnitude of vibration at the handles of pedestrian-controlled lawnmowers, including sulkies,
steering controls of ride-on lawnmowers and whole-body vibrations for operators on sulkies and ride-
on lawnmowers.
Although the magnitudes measured are obtained in an artificial operation, they nevertheless give an
indication of the values to be found in a real work situation.
G.2 Characterization of hand-arm vibration – Pedestrian-controlled lawnmowers
G.2.1 Direction of measurement
Translational vibration transmitted to the hand is related to the x, y, or z directions shown in Figure G.1.
ISO 5395-1:2013/Amd.1:2017(E)
z
x
a
y
z
x
a
y
z
x
y
a
Key
a
100 mm
Figure G.1 — Examples of transducer location/orientation (pedestrian-controlled machines)
If the handle design is not covered by one of the examples, the transducer for the hand-arm vibrations
shall be located at the normal operating hand position between the thumb and index finger. This
position shall be described in the test report.
G.2.2 Location of measurement
The machine shall be held with both hands. Measurements shall be carried out with the transducer as
close as possible to a point on the grip surface between the thumb and the index finger (see examples in
Figure G.1).
G.2.3 Magnitude of vibration
The magnitude of vibration shall be the frequency-weighted acceleration a in m/s , expressed as a
hw
root-mean-square (RMS) value. The frequency weighting shall be according to ISO 5349-1.
The duration time T shall be not less than 8 s for each measurement.
2 © ISO 2017 – All rights reserved
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.