EN ISO 9863-1:2016

Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers (ISO 9863-1:2016)

ISO 9863-1:2016 specifies a method for the determination of the thickness of geosynthetics at specified pressures and specified load plate areas or under specified point loads. It defines the pressures or the load at which the thickness is determined.
The test results are intended for identification purposes and for use in technical data sheets and/or as part of other test methods, e.g. tests of hydraulic properties.
The method is applicable to all geosynthetics.

Geokunststoffe - Bestimmung der Dicke unter festgelegten Drücken - Teil 1: Einzellagen (ISO 9863-1:2016)

Géosynthétiques - Détermination de l'épaisseur à des pressions spécifiées - Partie 1: Couches individuelles (ISO 9863-1:2016)

L'ISO 9863-1:2016 spécifie une méthode permettant de déterminer l'épaisseur des géosynthétiques à des pressions spécifiées et définit la pression à laquelle l'épaisseur nominale est déterminée.
Les résultats d'essai sont prévus à des fins d'identification et utilisés pour les fiches techniques et/ou comme partie d'autres méthodes d'essai, par exemple les essais des propriétés hydrauliques.
La méthode est applicable à tous les géosynthétiques.

Geosintetika - Ugotavljanje debeline pri predpisanih tlakih - 1. del: Enojne plasti (ISO 9863-1:2016)

Ta del standarda ISO 9863 določa metodo za ugotavljanje debeline geosintetikov pri predpisanih tlakih in v predpisanih območjih obremenitve ali pod predpisanimi točkovnimi obremenitvami. Določa vrednosti tlaka ali obremenitve, pri katerih se ugotavlja debelina.
Rezultati preskusov so namenjeni za identifikacijo in uporabo v tehničnih listih in/ali kot del drugih preskusnih metod (npr. preskusi hidravličnih lastnosti).
Metoda se uporablja za vse geosintetike.

General Information

• Status: Published
• Publication Date: 09-Aug-2016
• Withdrawal Date: 27-Feb-2017
• ICS: 59.080.70 - Geotextiles
• Technical Committee: CEN/TC 189 - Geotextiles and geotextile-related products
• Drafting Committee: CEN/TC 189/WG 3 - Mechanical testing
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 10-Aug-2016
• Completion Date: 10-Aug-2016
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN ISO 9863-1:2016 - Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers (ISO 9863-1:2016)

Relations

• Replaces: EN ISO 9863-1:2005 - Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers (ISO 9863-1:2005)
• Effective Date: 17-Aug-2016
• Amended By: EN ISO 9863-1:2016/A1:2019 - Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers - Amendment 1 (ISO 9863-1:2016/Amd 1:2019)
• Effective Date: 21-Feb-2018

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2016
1DGRPHãþD
SIST EN ISO 9863-1:2005
Geosintetika - Ugotavljanje debeline pri predpisanih tlakih - 1. del: Enojne plasti
(ISO 9863-1:2016)
Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers
(ISO 9863-1:2016)
Geokunststoffe - Bestimmung der Dicke unter festgelegten Drücken - Teil 1: Einzellagen
(ISO 9863-1:2016)
Géosynthétiques - Détermination de l'épaisseur à des pressions spécifiées - Partie 1:
Couches individuelles (ISO 9863-1:2016)
Ta slovenski standard je istoveten z: EN ISO 9863-1:2016
ICS:
59.080.70 Geotekstilije Geotextiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 9863-1
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2016
EUROPÄISCHE NORM
ICS 59.080.70 Supersedes EN ISO 9863-1:2005
English Version
Geosynthetics - Determination of thickness at specified
pressures - Part 1: Single layers (ISO 9863-1:2016)
Géosynthétiques - Détermination de l'épaisseur à des Geokunststoffe - Bestimmung der Dicke unter
pressions spécifiées - Partie 1: Couches individuelles festgelegten Drücken - Teil 1: Einzellagen (ISO 9863-
(ISO 9863-1:2016) 1:2016)
This European Standard was approved by CEN on 8 July 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9863-1:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 9863-1:2016) has been prepared by Technical Committee ISO/TC 221
“Geosynthetics” in collaboration with Technical Committee CEN/TC 189 “Geosynthetics” the secretariat
of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2017, and conflicting national standards
shall be withdrawn at the latest by February 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 9863-1:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9863-1:2016 has been approved by CEN as EN ISO 9863-1:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 9863-1
Second edition
2016-07-15
Geosynthetics — Determination of
thickness at specified pressures —
Part 1:
Single layers
Géosynthétiques — Détermination de l’épaisseur à des pressions
spécifiées —
Partie 1: Couches individuelles
Reference number
ISO 9863-1:2016(E)
©
ISO 2016
ISO 9863-1:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 9863-1:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Specimens . 2
7 Procedure. 3
7.1 General . 3
7.2 Procedure A (New specimens for each pressure) . 3
7.3 Procedure B (Incremental loading of individual specimens) . 3
7.4 Procedure C (Polymeric and bituminous geosynthetic barriers of uniform thickness) . 4
7.5 Procedure D (Polymeric and bituminous geosynthetic barriers of non-
uniform thickness) . 4
8 Expression of results . 4
9 Test report . 4
Annex A (normative) Details of presser points used for geosynthetics of non-uniform thickness .5
ISO 9863-1:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to confor
...