EN ISO 13428:2024
(Main)Geosynthetics - Determination of the protection efficiency of a geosynthetic against impact damage (ISO 13428:2024)
Geosynthetics - Determination of the protection efficiency of a geosynthetic against impact damage (ISO 13428:2024)
This document describes an index test for the determination of the protection efficiency of a geosynthetic on a hard surface, exposed to the impact load of a hemispherical object.
The index test measures the change in thickness of a thin lead plate lying between the geosynthetic and a rigid support.
It is also used as a performance test, by using the real rigid surface to protect and the real sequence of geosynthetics.
The test is applicable to all geosynthetics with apertures smaller than 15 mm (maximum size).
Geokunststoffe - Bestimmung der Schutzwirksamkeit eines Geokunststoffes bei Stoßbelastung (ISO 13428:2024)
Dieses Dokument legt eine Kenngrößenprüfung zur Bestimmung der Schutzwirksamkeit eines Geokunststoffs auf einer harten Oberfläche bei Stoßbelastung durch einen halbkugelförmigen Gegenstand fest.
Die Kenngrößenprüfung misst die Dickenänderung einer dünnen Bleiplatte, die zwischen dem Geokunststoff und einer starren Auflage eingefügt ist.
Sie wird durch Verwendung der tatsächlich zu schützenden starren Oberfläche und der tatsächlichen Aufeinanderfolge von Geokunststoffen auch als Leistungsprüfung angewendet.
Die Prüfung ist anwendbar für alle Geokunststoffe mit Öffnungen von weniger als 15 mm (Höchstmaß).
Géosynthétiques - Détermination de l'efficacité de protection d'un géosynthétique contre l'effet d'un impact (ISO 13428:2024)
Le présent document décrit un essai de caractérisation permettant de déterminer l’efficacité de la protection offerte par un produit géosynthétique sur une surface dure, soumis à l’impact d’un objet hémisphérique.
Cet essai de caractérisation mesure la variation d’épaisseur d’une mince plaque de plomb placée entre le géosynthétique et un support rigide.
Il peut être converti en essai de performance en utilisant la surface rigide réelle à protéger et la séquence réelle de géosynthétiques.
L’essai est applicable à tous les produits géosynthétiques dont l’ouverture de maille est inférieure à 15 mm (dimension maximale).
Geosintetika - Ugotavljanje zaščitne učinkovitosti geosintetike pri poškodbah zaradi udarcev (ISO 13428:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Geosintetika - Ugotavljanje zaščitne učinkovitosti geosintetike pri poškodbah
zaradi udarcev (ISO 13428:2024)
Geosynthetics - Determination of the protection efficiency of a geosynthetic against
impact damage (ISO 13428:2024)
Geokunststoffe - Bestimmung der Schutzwirksamkeit eines Geokunststoffes bei
Stoßbelastung (ISO 13428:2024)
Géosynthétiques - Détermination de l'efficacité de protection d'un géosynthétique contre
l'effet d'un impact (ISO 13428:2024)
Ta slovenski standard je istoveten z: EN ISO 13428:2024
ICS:
59.080.70 Geotekstilije Geotextiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 13428
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2024
EUROPÄISCHE NORM
ICS 59.080.70; 91.100.50 Supersedes EN ISO 13428:2005
English Version
Geosynthetics - Determination of the protection efficiency
of a geosynthetic against impact damage (ISO 13428:2024)
Géosynthétiques - Détermination de l'efficacité de Geokunststoffe - Bestimmung der Schutzwirksamkeit
protection d'un géosynthétique contre l'effet d'un eines Geokunststoffes bei Stoßbelastung (ISO
impact (ISO 13428:2024) 13428:2024)
This European Standard was approved by CEN on 29 September 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13428:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 13428:2024) has been prepared by Technical Committee ISO/TC 221
"Geosynthetics" in collaboration with Technical Committee CEN/TC 189 “Geosynthetics” the secretariat
of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2025, and conflicting national standards shall be
withdrawn at the latest by April 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13428:2005.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 13428:2024 has been approved by CEN as EN ISO 13428:2024 without any modification.
International
Standard
ISO 13428
Second edition
Geosynthetics — Determination
2024-10
of the protection efficiency of a
geosynthetic against impact damage
Géosynthétiques — Détermination de l'efficacité de protection
d'un géosynthétique contre l'effet d'un impact
Reference number
ISO 13428:2024(en) © ISO 2024
ISO 13428:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 13428:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Test specimens . 3
5.1 Sampling .3
5.2 Number and dimensions of test specimens .3
5.3 Conditioning.3
6 Apparatus . 3
6.1 General .3
6.2 Probe .3
6.3 Specimen support .3
6.4 Lead plate .4
6.5 Thickness gauge .5
7 Test procedure . 5
8 Calculation . 6
9 Test report . 7
Annex A (informative) Performance testing . 8
Bibliography . 9
iii
ISO 13428:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO [had/had not] received notice of
(a) patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 221 Geosynthetics, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 189, Geosynthetics, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 13428:2005), which has been technically
revised.
The main changes are as follows:
— the normative references have been updated;
— Figure 1 has been corrected;
— the thickness of lead plate has been modified to 2,0 mm.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 13428:2024(en)
Geosynthetics — Determination of the protection efficiency of
a geosynthetic against impact damage
1 Scope
This document describes an index test for the determination of the protection efficiency of a geosynthetic on
a hard surface, exposed to the impact load of a hemispherical object.
The index test measures the change in thickness of a thin lead plate lying between the geosynthetic and a
rigid support.
It is also used as a performance test, by using the real rigid surface to protect and the real sequence of
geosynthetics.
The test is applicable to all geosynthetics with apertures smaller than 15 mm (maximum size).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 554, Standard atmospheres for condition
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.