EN 13476-1:2007
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characteristics
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characteristics
This standard, together with EN 13476 2 and EN 13476 3, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be used for non-pressure underground drainage and sewerage systems.
This standard is applicable to:
a) structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by “U”;
b) structured-wall pipes and fittings, which are to be used buried in the ground both outside (application area code “U”) and within a building structure (application area code “D”); reflected in the marking of products by “UD”.
In conjunction with EN 13476 2 and EN 13476 3 it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints.
This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options.
EN 13476 2 and EN 13476 3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B.
This standard covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in clause 2 can be used with pipes and fittings conforming t
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 1: Allgemeine Anforderungen und Leistungsmerkmale
Diese Europäische Norm legt gemeinsam mit EN 13476-2 und EN 13476-3 Definitionen und allgemeine Anforderungen an Rohre, Formstücke und das Rohrleitungssystem aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) mit profilierter Wandung fest, die für erdverlegte, drucklos betriebene Abwasserkanäle und leitungen verwendet werden.
Diese Norm gilt für:
a) Rohre und Formstücke mit profilierter Wandung, die ausschließlich für erdverlegte Anwendungen außerhalb einer Gebäudestruktur vorgesehen sind; gekennzeichnet mit Anwendungs¬kennzeichen „U“;
b) Rohre und Formstücke mit profilierter Wandung, die sowohl für erdverlegte Anwendungen außerhalb der Gebäudestruktur (Anwendungskennzeichen „U“) als auch innerhalb einer Gebäudestruktur (Anwendungs¬kennzeichen „D“) vorgesehen sind; gekennzeichnet mit Anwendungs¬kennzeichen „UD“.
Gemeinsam mit EN 13476-2 und EN 13476-3 gilt dieser Teil für Rohre und Formstücke mit profilierter Wandung sowohl mit glatten Enden als auch mit angeformter Muffe mit elastomeren Dichtringverbindungen bzw. Verbindung durch Heizelement-Stumpf-, Extrusions- oder Heizwendelschweißen.
Dieser Teil legt allgemeine Aspekte fest und enthält Empfehlungen zur Auswahl nationaler Anforderungsstufen und -klassen, wofür Teil 2 und Teil 3 dieser Norm die Optionen enthält.
EN 13476-2 und EN 13476-3 legen Werkstoffeigenschaften, Maße und Toleranzen, Prüfverfahren, Prüfparameter und Anforderungen für Rohre mit glatten Innen- und Außenflächen, Typ A, sowie Rohre mit glatten Innen- und profilierten Außenflächen, Typ B, fest.
Diese Norm enthält, gemeinsam mit EN 13476-2 und EN 13476-3, Festlegungen für Maße von Rohren und Formstücken, für Werkstoffe, Rohrkonstruktionen, für Steifigkeitsklassen und Toleranzklassen und gibt Empfehlungen für die Einfärbung.
ANMERKUNG 1 Der Käufer bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissements sans pression enterrés - Systèmes de canalisation à parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 1: Exigences générales et caractéristiques de performance
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Cevni sistemi s strukturirano steno iz nemehčanega polivinilklorida (PVC-U), polipropilena (PP) in polietilena (PE) - 1. del: Splošne zahteve in zahtevane lastnosti
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characteristicsSystemes de canalisations en plastique pour les branchements et les collecteurs d'assainissements sans pression enterrés - Systemes de canalisation a parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylene (PP) et polyéthylene (PE) - Partie 1: Exigences générales et caractéristiques de performanceKunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 1: Allgemeine Anforderungen und LeistungsmerkmaleTa slovenski standard je istoveten z:EN 13476-1:2007SIST EN 13476-1:2007en;fr;de93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:SLOVENSKI
STANDARDSIST EN 13476-1:200701-julij-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13476-1May 2007ICS 93.030 English VersionPlastics piping systems for non-pressure underground drainageand sewerage - Structured-wall piping systems of unplasticizedpoly(vinyl chloride) (PVC-U), polypropylene (PP) andpolyethylene (PE) - Part 1: General requirements andperformance characteristicsSystèmes de canalisations en plastique pour lesbranchements et les collecteurs d'assainissements sanspression enterrés - Systèmes de canalisation à paroisstructurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 1:Exigences générales et caractéristiques de performanceKunststoff-Rohrleitungssysteme für erdverlegte druckloseAbwasserkanäle und -leitungen - Rohrleitungssysteme mitprofilierter Wandung aus weichmacherfreiemPolyvinylchlorid (PVC-U), Polypropylen (PP) undPolyethylen (PE) - Teil 1: Allgemeine Anforderungen undLeistungsmerkmaleThis European Standard was approved by CEN on 5 March 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13476-1:2007: E
Characteristics of PVC-U, PP and PE pipes and fittings 17 A.1 General 17 A.2 Material characteristics 17 A.3 Chemical resistance 17 A.4 Abrasion resistance 18 A.5 Hydraulic roughness 18 Annex B (informative)
Structural design 19 B.1 General 19 B.2 Structural design based on practical experience 19 B.3 Structural design based on a design calculations 21 B.4 Selection of fitting stiffness or class 21 Annex C (informative)
Designation of pipes and corresponding fittings 23 Annex D (informative)
Guidance in cleaning plastics pipes 24 D.1 Introduction 24 D.2 Cleaning and unblocking 24
(PVC-U), polypropylene (PP) and polyethylene (PE): — Part 1: General requirements and performance characteristics (this standard); — Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A; — Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B; — Part 4: Assessment of conformity (CEN/TS); — Part 5: Guidance for installation (CEN/TS).1 For pipes and fittings which have conformed to the relevant national standard before May 2007, as shown by the manufacturer or by a certification body, the national standard may continue to be applied until May 2009.
National standards specifically for pipes and fittings for the transport of surface water are not considered to be conflicting with this standard and may thus be allowed to coexist. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
1 The feasibility of this project is under study.
Introduction Due to the variety in materials, pipe constructions, application areas and classes, several combinations are possible. The purchaser or specifier may select between these possibilities by designating the pipe and fitting he or she prefers to use for each case, as described in Annex C, Designation of pipes and corresponding fittings, taking into account any particular requirements and relevant national regulations and installation practices or codes.
NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9. NOTE 3
For dimensions larger than DN 1200 OD/ID this document may serve as general guideline regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 4: Cast polyurethane sealing elements EN 13476-2:2007,
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B EN ISO 472:2001, Plastics — Vocabulary (ISO 472:1999) EN ISO 1043-1:2001, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 9969, Thermoplastics pipes — Determination of ring stiffness (ISO 9969:1994) ISO 11922-1:1997, Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series ISO 13967, Thermoplastics fittings — Determination of ring stiffness 3 Terms and definitions, symbols and abbreviations For the purposes of this standard, the terms and definitions given in EN ISO 472:2001, EN ISO 1043-1:2001, ISO 11922-1:1997 and the following apply. 3.1 Definitions
3.1.1 General definitions 3.1.1.1 application area code code used to mark pipes and fittings to indicate the permitted application area(s) for which they are intended, as follows:
U: code for the area more than 1 m from the building to which the buried piping system is connected;
D: code for the area under and within 1 m from the building where the pipes and fittings are buried
underground and are connected to the soil and waste discharge system of the building NOTE In the “D” application area, the existence of hot water discharge in addition to external forces from the surroundings is usual. 3.1.1.2 structured-wall pipes and fittings products which have an optimised design with regard to material usage to achieve the physical, mechanical and performance requirements of this standard NOTE For a description of the particular designs covered by this standard, see clause 5 in EN 13476-2:2007 and EN 13476-3:2007. 3.1.1.3 fabricated fitting fitting manufactured by heat forming and/or joining more than one piece of pipe and/or moulded component NOTE Sealed ring retaining components are not considered as a piece.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.