CEN/TS 14632:2023
(Main)Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
This document gives guidance on the assessment of conformity of GRP-UP (glass-reinforced thermosetting resins based on unsaturated polyesters) piping products and assemblies in accordance with EN ISO 23856. ISO 25780 and ISO 16611 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
This document also gives guidance on the assessment of conformity of GRP-UP manholes and inspection chambers (see EN 15383 for additional information). Pipes (see EN ISO 23856) are used for manufacturing the shafts and chamber units. Additional statements as needed to assess the conformity of manholes and inspection chambers are given in Annex F.
NOTE 1 For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).
NOTE 2 If third-party certification is involved, the certification body is accredited to ISO/IEC 17065 or EN ISO/IEC 17021 [3] as applicable.
Kunststoff-Rohrleitungssysteme für Wasserversorgung, Entwässerungssysteme und Abwasserleitungen mit und ohne Druck - Glasfaserverstärkte duroplastische Kunststoffe (GFK) auf der Basis von ungesättigtem Polyesterharz (UP) - Empfehlungen für die Beurteilung der Konformität
Dieses Dokument enthält Empfehlungen für die Beurteilung der Konformität von Rohrleitungsteilen und Bauteilkombinationen aus glasfaserverstärkten duroplastischen Kunststoffen auf der Basis von ungesättigtem Polyesterharz (GFK UP) nach EN ISO 23856, ISO 25780 und ISO 16611, die als Bestandteil des Qualitätsmanagementsystems im Qualitätssicherungsplan des Herstellers und für die Einführung von Drittstellenzertifizierungsverfahren vorgesehen sind.
Dieses Dokument enthält auch Empfehlungen für die Beurteilung der Konformität von Einsteig- und Kontrollschächten aus GFK-UP (siehe EN 15383 für weitere Angaben). Steigrohre und Schachteinheiten werden aus Rohren (siehe EN ISO 23856) gefertigt. Zusätzliche Angaben, die zur Beurteilung der Konformität von Einsteig und Kontrollschächten benötigt werden, sind in Anhang F enthalten.
ANMERKUNG 1 Für die Anwendung dieses Dokuments schließt der Begriff Polyesterharz (UP) auch Vinylesterharze (VE) mit ein.
ANMERKUNG 2 Im Fall von Drittstellenzertifizierung ist die Zertifizierungsstelle in Abhängigkeit von der Anwendung nach ISO/IEC 17065 oder EN ISO/IEC 17021 [3] zugelassen.
Systèmes de canalisations en plastique pour les branchements, les collecteurs d'assainissement et l'alimentation en eau, avec ou sans pression - Plastiques thermodurcissables renforcés de verre (PRV) à base de résine polyester (UP) - Guide pour l'évaluation de conformité
Cevni sistemi iz polimernih materialov za odvodnjavanje, kanalizacijo in oskrbo z vodo, s tlakom in brez njega - S steklenimi vlakni okrepljeni duromerni materiali (GRP), ki temeljijo na nenasičeni poliestrski smoli (UP) - Navodilo za ugotavljanje skladnosti
Ta tehnična specifikacija vsebuje navodila za ugotavljanje skladnosti cevnih izdelkov in sestavov iz duromernih materialov, okrepljenih s steklenimi vlakni, ki temeljijo na nenasičeni poliestrski smoli (GRP-UP), s standardoma EN 1796 in EN 14364, pri čemer naj bi se ta navodila vključila v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti, vsebuje pa tudi navodila za vzpostavitev postopka certificiranja, ki ga izvajajo tretje osebe. Ta tehnična specifikacija podaja tudi navodila za ugotavljanje skladnosti vstopnih in revizijskih jaškov iz duromernih materialov, okrepljenih s steklenimi vlakni, ki temeljijo na nenasičeni poliestrski smoli, s standardom prEN 15383. V skladu s standardom EN 14364 se cevi uporabljajo za izdelavo vstopnih in revizijskih jaškov. Dodatne izjave, ki so potrebne za ugotavljanje skladnosti vstopnih in revizijskih jaškov, so navedene v dodatku F. OPOMBA 1: Priporoča se, da je sistem vodenja kakovosti skladen s standardom EN ISO 9001 [3] oziroma da ni manj strog od ustreznih zahtev iz tega standarda. OPOMBA 2: Če certificiranje izvajajo tretje osebe, se priporoča, da je certifikacijski organ akreditiran v skladu s standardom EN 45011 [1], EN 45012 [2] ali EN ISO/IEC 17021 [5].
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2023
Nadomešča:
SIST-TS CEN/TS 14632:2012
Cevni sistemi iz polimernih materialov za odvodnjavanje, kanalizacijo in oskrbo z
vodo, s tlakom in brez njega - S steklenimi vlakni okrepljeni duromerni materiali
(GRP), ki temeljijo na nenasičeni poliestrski smoli (UP) - Navodilo za ugotavljanje
skladnosti
Plastics piping systems for drainage, sewerage and water supply, pressure and non-
pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated
polyester resin (UP) - Guidance for the assessment of conformity
Kunststoff-Rohrleitungssysteme für die Entwässerung und Wasserversorgung mit und
ohne Druck - Glasfaserverstärkte duroplastische Kunststoffe (GFK) auf der Basis von
Polyesterharz (UP) - Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour les branchements, les collecteurs
d'assainissement et l'alimentation en eau, avec ou sans pression - Plastiques
thermodurcissables renforcés de verre (PRV) à base de résine polyester (UP) - Guide
pour l'évaluation de conformité
Ta slovenski standard je istoveten z: CEN/TS 14632:2023
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
83.120 Ojačani polimeri Reinforced plastics
91.140.60 Sistemi za oskrbo z vodo Water supply systems
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 14632
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
June 2023
TECHNISCHE SPEZIFIKATION
ICS 91.140.60; 91.140.80; 93.030; 23.040.05 Supersedes CEN/TS 14632:2012
English Version
Plastics piping systems for drainage, sewerage and water
supply, pressure and non-pressure - Glass-reinforced
thermosetting plastics (GRP) based on unsaturated
polyester resin (UP) - Guidance for the assessment of
conformity
Kunststoff-Rohrleitungssysteme für die Entwässerung
und Wasserversorgung mit und ohne Druck -
Glasfaserverstärkte duroplastische Kunststoffe (GFK)
auf der Basis von Polyesterharz (UP) - Empfehlungen
für die Beurteilung der Konformität
This Technical Specification (CEN/TS) was approved by CEN on 7 May 2023 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14632:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 10
4 Abbreviated terms . 12
5 General . 12
6 Testing and inspection . 13
6.1 General . 13
6.2 Type testing . 13
6.3 Audit tests (AT) . 16
6.4 Quality control tests . 18
Annex A (normative) Procedures for dealing with test data provided by the manufacturer and for
witnessed tests in a manufacturer's laboratory . 20
A.1 General . 20
A.2 Test data provided by the manufacturer . 20
A.3 Witnessed tests in a manufacturer's laboratory . 20
A.3.1 General . 20
A.3.2 Control of witnessed tests . 20
Annex B (normative) Definitions of changes in material, design and process . 21
B.1 General . 21
B.2 Change in materials — Reinforcements . 21
B.3 Resins . 21
B.3.1 General . 21
B.3.2 Curing agents or systems . 22
B.3.3 Fillers and/or aggregates . 22
B.3.4 Joint materials . 22
B.3.4.1 Gasket sealed joints . 22
B.3.4.2 Bonded joints . 22
B.4 Change in design . 23
B.5 Change in process. 23
Annex C (normative) Tests to assess the effects of changes . 24
C.1 Tests . 24
C.2 Evaluation of test results . 24
C.2.1 Initial properties . 24
C.2.2 Reduced long-term tests . 24
Annex D (normative) Parameters and criteria for reduced long-term tests (RLTT) . 26
D.1 General . 26
D.2 Reduced long-term test parameters . 26
D.2.1 Reduced parameters for long-term failure pressure . 26
D.2.2 Reduced parameters for the resistance to strain corrosion . 26
D.2.2.1 General . 26
D.2.2.2 Procedure using failure points . 26
D.2.2.3 Procedure using specified levels . 27
D.2.2.3.1 . General
............................................................................................................................................................................. 27
D.2.2.3.2 . Using deflection
............................................................................................................................................................................. 27
D.2.2.3.3 . Using strain
............................................................................................................................................................................. 27
D.2.3 Reduced parameters for ultimate long-term resistance to failure in a deflected condition27
D.3 Evaluation of results of destructive RLTTs (see D.2.1, D.2.2 and D.2.3) . 28
D.3.1 General . 28
D.3.2 Example . 29
Annex E (normative) Reduced long-term testing (RLTT) of the determination of wet creep factor32
E.1 General . 32
E.2 Evaluation of results and criteria . 32
E.2.1 General . 32
E.2.2 Example . 33
Annex F (normative) Additional statements for manholes and inspection chambers . 36
F.1 General . 36
F.2 Tests specific to manholes and chambers . 36
F.2.1 Longitudinal compressive strength . 36
F.2.2 Determination of the resistance of installed steps to vertical and horizontal loading . 36
F.3 Type tests . 36
F.4 Audit tests . 36
F.5 Batch release tests . 36
Annex G (informative) Consequence Classes and Quality Levels . 37
G.1 General . 37
Bibliography .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.