EN ISO 7668:2010
(Main)Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees (ISO 7668:2010)
Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees (ISO 7668:2010)
ISO 7668:2010 specifies methods for the measurement of specular reflectance and specular gloss of flat samples of anodized aluminium using geometries of 20° (Method A), 45° (Method B), 60° (Method C) and 85° (Method D); and of specular reflectance by an additional 45° method (Method E) employing a narrow acceptance angle.
The methods described are intended mainly for use with clear anodized surfaces. They can be used with colour-anodized aluminium, but only with similar colours.
Anodisieren von Aluminium und Aluminiumlegierungen - Messung des gerichteten Reflexionsgrades und des Spiegelglanzes von anodisch erzeugten Oxidschichten bei Winkeln von 20°, 45°, 60° oder 85° (ISO 7668:2010)
Diese Internationale Norm legt Verfahren zur Messung des gerichteten Reflexionsgrades und des Spiegelglanzes von ebenen Proben aus anodisch oxidiertem Aluminium unter Anwendung der geometrischen Messbedingungen unter 20° (Verfahren A), 45° (Verfahren B), 60° (Verfahren C) und 85° (Verfahren D) sowie ein weiteres Verfahren zur Messung des gerichteten Reflexionsgrades unter 45° (Verfahren E) fest, bei dem ein kleiner Empfängerwinkel verwendet wird.
Die beschriebenen Verfahren sind hauptsächlich für farblos anodisierte Oberflächen vorgesehen. Sie können für farbig anodisiertes Aluminium verwendet werden, aber nur bei gleichen Farben.
Anodisation de l'aluminium et de ses alliages - Mesurage des caractéristiques de réflectivité et de brillant spéculaires des couches anodiques à angle fixe de 20 degrés, 45 degrés, 60 degrés ou 85 degrés (ISO 7668:2010)
L'ISO 7668:2010 spécifie des méthodes de mesure de la réflectivité spéculaire et du brillant spéculaire d'échantillons plats d'aluminium anodisé sous des angles de 20° (Méthode A), 45° (Méthode B), 60° (Méthode C) et 85° (Méthode D), plus une autre méthode à 45° (Méthode E) à petit angle d'ouverture pour le mesurage de la réflectivité spéculaire.
Les méthodes décrites sont principalement utilisables sur des surfaces plates anodisées claires. Elles peuvent être utilisées sur de l'aluminium anodisé coloré, mais dans ce cas, uniquement pour des couleurs semblables.
Anodizacija aluminija in aluminijevih zlitin - Merjenje odbojnosti in sijaja anodizirane plasti pod koti 20°, 45°, 60° ali 85° (ISO 7668:2010)
Ta mednarodni standard določa metode za merjenje odbojnosti in sijaja ploščatih vzorcev anodiziranega aluminija z uporabo geometrij 20° (metoda A), 45° (metoda B), 60° (metoda C) in 85° (metoda D) in odbojnosti z dodatno metodo 45° (metoda E) z uporabo ozkega kota sprejemljivosti. Opisane metode so namenjene predvsem uporabi s prozornimi anodiziranimi površinami. Lahko se uporabljajo z barvno anodiziranmi aluminijem, a le podobnih barv.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7668:2012
01-januar-2012
1DGRPHãþD
SIST EN 12373-11:2002
Anodizacija aluminija in aluminijevih zlitin - Merjenje odbojnosti in sijaja
anodizirane plasti pod koti 20°, 45°, 60° ali 85° (ISO 7668:2010)
Anodizing of aluminium and its alloys - Measurement of specular reflectance and
specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60
degrees or 85 degrees (ISO 7668:2010)
Anodisieren von Aluminium und Aluminiumlegierungen - Messung des gerichteten
Reflexionsgrades und des Spiegelglanzes von anodisch erzeugten Oxidschichten bei
Winkeln von 20°, 45°, 60° oder 85° (ISO 7668:2010)
Anodisation de l'aluminium et de ses alliages - Mesurage des caractéristiques de
réflectivité et de brillant spéculaires des couches anodiques à angle fixe de 20 degrés,
45 degrés, 60 degrés ou 85 degrés (ISO 7668:2010)
Ta slovenski standard je istoveten z: EN ISO 7668:2010
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
SIST EN ISO 7668:2012 de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 7668:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 7668:2012
EUROPEAN STANDARD
EN ISO 7668
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2010
ICS 25.220.20 Supersedes EN 12373-11:2000
English Version
Anodizing of aluminium and its alloys - Measurement of specular
reflectance and specular gloss of anodic oxidation coatings at
angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees
(ISO 7668:2010)
Anodisation de l'aluminium et de ses alliages - Mesurage Anodisieren von Aluminium und Aluminiumlegierungen -
des caractéristiques de réflectivité et de brillant spéculaires Messung des gerichteten Reflexionsgrades und des
des couches anodiques à angle fixe de 20 degrés, 45 Spiegelglanzes von anodisch erzeugten Oxidschichten bei
degrés, 60 degrés ou 85 degrés (ISO 7668:2010) Winkeln von 20°, 45°, 60° oder 85° (ISO 7668:2010)
This European Standard was approved by CEN on 30 October 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7668:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 7668:2012
EN ISO 7668:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 7668:2012
EN ISO 7668:2010 (E)
Foreword
This document (EN ISO 7668:2010) has been prepared by Technical Committee ISO/TC 79 “Light metals and
their alloys” in collaboration with Technical Committee CEN/TC 132 “Aluminium and aluminium alloys” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the
latest by May 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12373-11:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.