EN 913:2018/prA1
(Amendment)Gymnastic equipment - General safety requirements and test methods
Gymnastic equipment - General safety requirements and test methods
This document specifies general safety requirements and test methods for all pieces of gymnastic and sports equipment and for all pieces of equipment for the use of physical education, training and competition, intended for use supervised by a competent person and not specified in other, individual standards and/or federation rules.
Turngeräte - Allgemeine sicherheitstechnische Anforderungen und Prüfverfahren
No Scope available
Matériel de gymnastique - Exigences générales de sécurité et méthodes d'essai
No Scope Available
Gimnastična oprema - Splošne varnostne zahteve in preskusne metode
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 913:2019/oprA1:2020
01-september-2020
Gimnastična oprema - Splošne varnostne zahteve in preskusne metode
Gymnastic equipment - General safety requirements and test methods
Turngeräte - Allgemeine sicherheitstechnische Anforderungen und Prüfverfahren
Matériel de gymnastique - Exigences générales de sécurité et méthodes d'essai
Ta slovenski standard je istoveten z: EN 913:2018/prA1
ICS:
97.220.30 Oprema za dvoranske športe Indoor sports equipment
SIST EN 913:2019/oprA1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 913:2019/oprA1:2020
---------------------- Page: 2 ----------------------
SIST EN 913:2019/oprA1:2020
DRAFT
EUROPEAN STANDARD
EN 913:2018
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
May 2020
ICS
English Version
Gymnastic equipment - General safety requirements and
test methods
Matériel de gymnastique - Exigences générales de Turngeräte - Allgemeine sicherheitstechnische
sécurité et méthodes d'essai Anforderungen und Prüfverfahren
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 136.
This draft amendment A1, if approved, will modify the European Standard EN 913:2018. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 913:2018/prA1:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 913:2019/oprA1:2020
EN 913:2018/prA1:2020 (E)
Contents Page
European foreword . 3
1 Modifications to Annex A . 4
2 Modifications to Annex B . 8
2
---------------------- Page: 4 ----------------------
SIST EN 913:2019/oprA1:2020
EN 913:2018/prA1:2020 (E)
European foreword
This document (EN 913:2018/prA1:2020) has been prepared by Technical Committee CEN/TC 136
“Sports, playgrounds and other recreational facilities and equipment”, the secretariat of which is held
by DIN.
This document is currently submitted to the CEN Enquiry.
3
---------------------- Page: 5 ----------------------
SIST EN 913:2019/oprA1:2020
EN 913:2018/prA1:2020 (E)
1 Modifications to Annex A
Replace the entire Annex A by the following:
“
Annex A
(normative)
Determination of entrapment
A.1 Principle
Test probes of specified dimensions are offered to potential entrapment points and a note is made of
whether or not they can be inserted.
In situations of doubt when using the probes relating to the tolerance an accurate measurement should
be made to ensure the opening is in accordance with the nominal dimension.
All tests shall be performed in the most onerous way.
A.2 Apparatus
Test probes of dimensions as described in Figures A.1 and A.2.
A.3 Conditioning and test temperature
Condition the equipment and test probes for a minimum of 3 h at the test temperature of (23 ± 2) °C.
A.4 Procedure
A.4.1 Head and neck entrapment
A.4.1.1 General
The probe shall be applied with its longitudinal axis
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.