EN ISO 13703:2000
(Main)Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)
Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)
Recommends minimum requirements and gives guidance for the design and installation of new piping systems on production platforms located offshore for the petroleum and natural gas industries. It covers piping systems up to 690 bar g maximum within a temperature range of -29°C to 343°C.
Erdöl- und Erdgasindustrien - Auslegung und Verlegung von Rohrleitungssystemen auf Offshore-Förderplattformen (ISO 13703:2000)
Diese Internationale Norm legt Mindestanforderungen fest und enthält einen Leitfaden für die Auslegung und Verlegung von neuen Rohrleitungssystemen auf Offshore-Förderplattformen für die Erdöl- und Erdgasindustrien. Die Norm gilt für Rohrleitungssysteme bis max. 60 000 kPa (ga) mit Temperaturgrenzwerten für die Werkstoffe in
Übereinstimmung mit den Anforderungen in ASME B 31.3.
ANMERKUNG Für Anwendungsfälle außerhalb dieser Druck- und Temperaturbereiche kann diese Internationale Norm angewendet werden, jedoch sollte besonders auf die Werkstoffeigenschaften geachtet werden.
Anhang A enthält einige Lösungsbeispiele für Problemfälle bei der Auslegung von Rohrleitungen.
Industries du pétrole et du gaz naturel - Conception et installation de systèmes de tuyauterie sur les plates-formes de production en mer (ISO 13703:2000)
La présente Norme internationale spécifie les exigences minimales et donne des lignes directrices pour la conception et l'installation de nouveaux systèmes de tuyauterie sur les plates-formes de production situées en mer, pour les industries du pétrole et du gaz naturel. Elle couvre les systèmes de tuyauterie supportant une pression maximale de 69 000 kPa, dans les limites d'une échelle de températures pour des matériaux répondant aux exigences de l'ASME B31.3.
L'annexe A donne quelques exemples pratiques pour résoudre des problèmes de conception de tuyauterie.
Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)
General Information
Relations
Related Packages
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2001
Petroleum and natural gas industries - Design and installation of piping systems
on offshore production platforms (ISO 13703:2000)
Petroleum and natural gas industries - Design and installation of piping systems on
offshore production platforms (ISO 13703:2000)
Erdöl- und Erdgasindustrien - Auslegung und Verlegung von Rohrleitungssystemen auf
Offshore-Förderplattformen (ISO 13703:2000)
Industries du pétrole et du gaz naturel - Conception et installation de systemes de
tuyauterie sur les plates-formes de production en mer (ISO 13703:2000)
Ta slovenski standard je istoveten z: EN ISO 13703:2000
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 13703
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2000
ICS 75.180.10
English version
Petroleum and natural gas industries - Design and installation of
piping systems on offshore production platforms (ISO
13703:2000)
Industries du pétrole et du gaz naturel - Conception et Erdöl- und Erdgasindustrien - Auslegung und Verlegung
installation de systèmes de tuyauterie sur les plates-formes von Rohrleitungssystemen auf Offshore-Förderplattformen
de production en mer (ISO 13703:2000) (ISO 13703:2000)
This European Standard was approved by CEN on 9 December 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13703:2000 E
worldwide for CEN national Members.
Page 2
CORRECTED 2002-07-24
Foreword
This document (ISO 13703:2000) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum and natural gas industries", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2001, and conflicting national
standards shall be withdrawn at the latest by June 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 13703:2000 has been approved by CEN as a
European Standard without any modifications.
INTERNATIONAL ISO
STANDARD 13703
First edition
2000-12-15
Petroleum and natural gas industries —
Design and installation of piping systems
on offshore production platforms
Industries du pétrole et du gaz naturel — Conception et installation de
systèmes de tuyauterie sur les plates-formes de production en mer
Reference number
ISO 13703:2000(E)
©
ISO 2000
ISO 13703:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
ISO 13703:2000(E)
Contents Page
Foreword.v
Introduction.vi
1 Scope .1
2 Normative references .1
3 Terms, definitions, symbols and abbreviated terms.2
3.1 Terms and definitions .2
3.2 Symbols and abbreviated terms .4
4 General considerations.6
4.1 Materials .6
4.2 Code of pressure piping .7
4.3 Demarcation between systems with different pressure ratings.7
4.4 Corrosion considerations .9
5 Piping design .10
5.1 Pipe material grades.10
5.2 Sizing criteria — General .12
5.3 Sizing methods for liquid lines.12
5.4 Sizing criteria for single-phase gas lines.19
5.5 Sizing criteria for gas/liquid two-phase lines .23
5.6 Pipe wall thicknesses.26
5.7 Joint connections .30
5.8 Expansion and flexibility.31
5.9 Start-up provisions.32
6 Selection of valves .32
6.1 General.32
6.2 Types of valves .33
6.3 Fire resistance of valves .35
6.4 Valve sizing .35
6.5 Valve pressure and temperature ratings.36
6.6 Valve materials.37
7 Fittings and flanges.37
7.1 General.37
7.2 Welded fittings .38
7.3 Screwed fittings .38
7.4 Branch connections .38
7.5 Flanges .39
7.6 Proprietary connectors .41
7.7 Special requirements for sulfide stress-cracking service.41
7.8 Erosion prevention .41
8 Design considerations for particular piping systems.41
8.1 General.41
8.2 Wellhead accessory items .41
8.3 Flowline and flowline accessories.42
8.4 Production manifolds.45
8.5 Process vessel piping .45
8.6 Utility systems.47
8.7 Heating fluid and glycol systems.48
8.8 Pressure relief and disposal systems .48
8.9 Drain systems .50
ISO 13703:2000(E)
8.10 Bridge piping between platforms.50
8.11 Risers .50
8.12 Sampling valves.51
9 Considerations of related items .51
9.1 General.51
9.2 Layout .51
9.3 Elevations .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.