EN ISO 13680:2025
(Main)Oil and gas industries including lower carbon energy - Corrosion-resistant alloy seamless products for use as casing, tubing, coupling stock and accessory material - Technical delivery conditions (ISO 13680:2024)
Oil and gas industries including lower carbon energy - Corrosion-resistant alloy seamless products for use as casing, tubing, coupling stock and accessory material - Technical delivery conditions (ISO 13680:2024)
This document specifies the technical delivery conditions for corrosion-resistant alloy seamless products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels:
PSL-1, which is the basis of this document;
PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the ISO 15156 series or NACE MR0175.
This document contains no provisions relating to the connection of individual lengths of pipe. Demonstration of conformance to ISO 15156-3:2020 or NACE MR0175-2021 of material affected by end sizing, connection manufacture or welding operations is outside the scope of this document.
This document contains provisions relating to marking of tubing and casing after threading.
This document is applicable to the following five groups of products:
a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure;
b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy;
c) group 3, which is composed of stainless alloys with an austenitic structure (iron base);
d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base);
e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure.
Öl- und Gasindustrie einschließlich kohlenstoffarmer Energieträger - Nahtlose Rohre aus korrosionsbeständigen Legierungen zur Verwendung als Futter- oder Steigrohre sowie Muffenvorrohre und Zusatzmaterial - Technische Lieferbedingungen (ISO 13680:2024)
Industries du pétrole et du gaz y compris les énergies à faible teneur en carbone - Produits sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production, tubes-ébauches pour manchons et matériau pour accessoires - Conditions techniques de livraison (ISO 13680:2024)
Le présent document spécifie les conditions techniques de livraison des produits sans soudure en acier allié résistant à la corrosion, utilisés comme tubes de cuvelage, tubes de production, tubes-ébauches pour manchons et matériau pour accessoires (y compris les tubes-ébauches pour manchons et matériau pour accessoires en barres), pour deux niveaux de spécification de produit:
— PSL-1, qui constitue la base du présent document;
— PSL-2, qui fournit des exigences supplémentaires pour un produit destiné à être à la fois résistant à la corrosion et résistant à la fissuration pour les environnements et la méthode de qualification spécifiés à l'Annexe G et dans la série ISO 15156 ou dans la NACE MR0175.
Le présent document ne contient aucune disposition relative au raccordement de longueurs de tube individuelles. La démonstration de la conformité à l'ISO 15156-3:2020 ou à la NACE MR0175-2021 des matériaux affectés par le dimensionnement des extrémités, la fabrication des raccords ou les opérations de soudage ne relèvent pas du domaine d'application du présent document.
Le présent document contient des dispositions relatives au marquage des tubes de production et de cuvelage après filetage.
Le présent document s'applique aux cinq groupes de produits suivants:
a) le groupe 1, qui est composé d'alliages inoxydables à structure martensitique ou martensitique/ferritique;
b) le groupe 2, qui est composé d'alliages inoxydables à structure ferritique austénitique, tels que les alliages inoxydables duplex et super-duplex;
c) le groupe 3, qui est composé d'alliages inoxydables à structure austénitique (à base de fer);
d) le groupe 4, qui est composé d'alliages à base de nickel à structure austénitique (à base de nickel);
e) le groupe 5, qui est uniquement composé de barres (Annexe F) dans les alliages à base de nickel durcis par vieillissement à structure austénitique.
Naftna in plinska industrija, vključno z nizkoogljično energijo - Nevarjeni izdelki iz korozijsko odpornih zlitin, ki se uporabljajo kot zaščitne, proizvodne in priključne cevi ter pribor - Tehnični dobavni pogoji (ISO 13680:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2025
Nadomešča:
SIST EN ISO 13680:2020
Naftna in plinska industrija, vključno z nizkoogljično energijo - Nevarjeni izdelki iz
korozijsko odpornih zlitin, ki se uporabljajo kot zaščitne, proizvodne in priključne
cevi ter pribor - Tehnični dobavni pogoji (ISO 13680:2024)
Oil and gas industries including lower carbon energy - Corrosion-resistant alloy seamless
products for use as casing, tubing, coupling stock and accessory material - Technical
delivery conditions (ISO 13680:2024)
Öl- und Gasindustrie einschließlich kohlenstoffarmer Energieträger - Nahtlose Rohre aus
korrosionsbeständigen Legierungen zur Verwendung als Futter- oder Steigrohre sowie
Muffenvorrohre und Zusatzmaterial - Technische Lieferbedingungen (ISO 13680:2024)
Industries du pétrole et du gaz y compris les énergies à faible teneur en carbone -
Produits sans soudure en acier allié résistant à la corrosion utilisés comme tubes de
cuvelage, tubes de production, tubes-ébauches pour manchons et matériau pour
accessoires - Conditions techniques de livraison (ISO 13680:2024)
Ta slovenski standard je istoveten z: EN ISO 13680:2025
ICS:
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 13680
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2025
EUROPÄISCHE NORM
ICS 77.140.75; 75.180.10
English Version
Oil and gas industries including lower carbon energy -
Corrosion-resistant alloy seamless products for use as
casing, tubing, coupling stock and accessory material -
Technical delivery conditions (ISO 13680:2024)
Industries du pétrole et du gaz y compris les énergies à Öl- und Gasindustrie einschließlich kohlenstoffarmer
faible teneur en carbone - Produits sans soudure en Energieträger - Nahtlose Rohre aus
acier allié résistant à la corrosion utilisés comme tubes korrosionsbeständigen Legierungen zur Verwendung
de cuvelage, tubes de production, tubes-ébauches pour als Futter- oder Steigrohre sowie Muffenvorrohre und
manchons et matériau pour accessoires - Conditions Zusatzmaterial - Technische Lieferbedingungen (ISO
techniques de livraison (ISO 13680:2024) 13680:2024)
This European Standard was approved by CEN on 12 October 2025.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13680:2025 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 13680:2024 has been prepared by Technical Committee ISO/TC 67 "Oil and gas
industries including lower carbon energy” of the International Organization for Standardization (ISO)
and has been taken over as EN ISO 13680:2025 by Technical Committee CEN/TC 12 “Oil and gas
industries including lower carbon energy” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2026, and conflicting national standards shall be
withdrawn at the latest by April 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 13680:2024 has been approved by CEN as EN ISO 13680:2025 without any modification.
International
Standard
ISO 13680
Fifth edition
Oil and gas industries including
2024-05
lower carbon energy — Corrosion-
resistant alloy seamless products
for use as casing, tubing, coupling
stock and accessory material —
Technical delivery conditions
Industries du pétrole et du gaz y compris les énergies à faible
teneur en carbone — Produits sans soudure en acier allié
résistant à la corrosion utilisés comme tubes de cuvelage, tubes
de production, tubes-ébauches pour manchons et matériau pour
accessoires — Conditions techniques de livraison
Reference number
ISO 13680:2024(en) © ISO 2024
ISO 13680:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 13680:2024(en)
Contents Page
Foreword .vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, abbreviated terms and symbols . 4
3.1 Terms and definitions .4
3.2 Abbreviated terms .6
3.3 Symbols .7
4 General . 8
4.1 Dual normative references .8
4.2 Units of measurement .8
5 Information supplied by the purchaser . 8
6 Manufacturing process . 10
6.1 Melting practices .10
6.2 Product manufacturing process .10
6.3 Pipe end sizing .11
6.4 Straightening . .11
6.5 Processes requiring validation .11
6.6 Traceability . 12
6.7 Manufacturing procedure qualification test . 12
6.8 Process for update of alloys and/or grades . 12
7 Material requirements .12
7.1 Chemical composition . 12
7.2 Tensile properties . 13
7.3 Hardness properties . 13
7.4 Charpy V-notch test properties — General requirements . 13
7.4.1 Evaluation of test results . 13
7.4.2 Critical thickness . 13
7.4.3 Specimen size, orientation and hierarchy . . 13
7.4.4 Alternative size impact test specimens .14
7.4.5 Sub-size test specimens .14
7.4.6 Test temperature . .14
7.5 Charpy V-notch — Absorbed energy requirements for coupling stock and accessory
material — All grades .14
7.5.1 General .14
7.5.2 Requirements for all grades .14
7.6 Charpy V-notch — Absorbed energy requirements for pipe — All grades . 15
7.7 Flattening requirements .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.