Textiles - Professional care, drycleaning and wetcleaning of fabrics and garments - Part 5: Procedure for testing performance when cleaning and finishing using dibutoxymethane (ISO 3175-5:2019)

This document specifies drycleaning procedures for dibutoxymethane [1-(butoxymethoxy) butane], using commercial drycleaning machines, for fabrics and garments. It comprises procedures for normal and sensitive materials.

Textilien - Professionelle Pflege, Chemischreinigung und Nassreinigung von textilen Flächengebilden und Kleidungsstücken - Teil 5: Verfahren zum Prüfen der Leistung beim Reinigen und Nachbehandeln mit Dibutoxymethan (ISO 3175-5:2019)

Dieses Dokument legt Verfahren der Chemischreinigung von textilen Flächengebilden und Kleidungs-stücken mit Dibutoxymethan [1 (Butoxymethoxy) butan] fest, bei denen Chemisch¬reinigungsmaschinen für gewerbliche Zwecke angewendet werden. Es enthält Verfahren für normale und empfindliche Textilien.

Textiles - Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements - Partie 5: Mode opératoire pour évaluer la résistance au nettoyage et à la finition lors du traitement au dibutoxyméthane (ISO 3175-5:2019)

Le présent document spécifie des modes opératoires de nettoyage à sec au dibutoxyméthane [1‑(butoxyméthoxy) butane] mettant en œuvre des machines professionnelles de nettoyage à sec pour les étoffes et les vêtements. Il comporte des modes opératoires pour les articles normaux et sensibles.

Tekstilije - Kemično čiščenje, suho in mokro čiščenje izdelkov in oblačil - 5. del: Postopek preskušanja učinkovitosti pri čiščenju in plemenitenju z dibutoksimetanom (ISO 3175-5:2019)

Ta dokument določa postopke za kemično čiščenje z dibutoksimetanom [1-(butoksimetoksi) butan], pri čemer se uporabljajo komercialni stroji za kemično čiščenje, in sicer za tekstilne izdelke in oblačila. Zajema postopke za običajne in občutljive materiale.

General Information

Status
Published
Publication Date
15-Oct-2019
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
16-Oct-2019
Completion Date
16-Oct-2019

Buy Standard

Standard
EN ISO 3175-5:2019
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 3175-5:2019
01-december-2019

Tekstilije - Kemično čiščenje, suho in mokro čiščenje izdelkov in oblačil - 5. del:

Postopek preskušanja učinkovitosti pri čiščenju in plemenitenju z
dibutoksimetanom (ISO 3175-5:2019)

Textiles - Professional care, drycleaning and wetcleaning of fabrics and garments - Part

5: Procedure for testing performance when cleaning and finishing using
dibutoxymethane (ISO 3175-5:2019)

Textilien - Professionelle Pflege, Chemischreinigung und Nassreinigung von textilen

Flächengebilden und Kleidungsstücken - Teil 5: Verfahren zum Prüfen der Leistung beim

Reinigen und Nachbehandeln mit Dibutoxymethan (ISO 3175-5:2019)

Textiles - Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des

vêtements - Partie 5: Mode opératoire pour évaluer la résistance au nettoyage et à la

finition lors du traitement au dibutoxyméthane (ISO 3175-5:2019)
Ta slovenski standard je istoveten z: EN ISO 3175-5:2019
ICS:
59.080.01 Tekstilije na splošno Textiles in general
SIST EN ISO 3175-5:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3175-5:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 3175-5:2019
EN ISO 3175-5
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 59.080.01
English Version
Textiles - Professional care, drycleaning and wetcleaning
of fabrics and garments - Part 5: Procedure for testing
performance when cleaning and finishing using
dibutoxymethane (ISO 3175-5:2019)

Textiles - Entretien professionnel, nettoyage à sec et Textilien - Professionelle Pflege, Chemischreinigung

nettoyage à l'eau des étoffes et des vêtements - Partie und Nassreinigung von textilen Flächengebilden und

5: Mode opératoire pour évaluer la résistance au Kleidungsstücken - Teil 5: Verfahren zum Prüfen der

nettoyage et à la finition lors du traitement au Leistung beim Reinigen und Nachbehandeln mit

dibutoxyméthane (ISO 3175-5:2019) Dibutoxymethan (ISO 3175-5:2019)
This European Standard was approved by CEN on 7 April 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3175-5:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3175-5:2019
EN ISO 3175-5:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 3175-5:2019
EN ISO 3175-5:2019 (E)
European foreword

This document (EN ISO 3175-5:2019) has been prepared by Technical Committee ISO/TC 38 "Textiles"

in collaboration with Technical Committee CEN/TC 248 “Textiles and textile products” the secretariat of

which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be

withdrawn at the latest by April 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 3175-5:2019 has been approved by CEN as EN ISO 3175-5:2019 without any

modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 3175-5:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 3175-5:2019
INTERNATIONAL ISO
STANDARD 3175-5
First edition
2019-09
Textiles — Professional care,
drycleaning and wetcleaning of fabrics
and garments —
Part 5:
Procedure for testing performance
when cleaning and finishing using
dibutoxymethane
Textiles — Entretien professionnel, nettoyage à sec et nettoyage à
l'eau des étoffes et des vêtements —
Partie 5: Mode opératoire pour évaluer la résistance au nettoyage et à
la finition lors du traitement au dibutoxyméthane
Reference number
ISO 3175-5:2019(E)
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 3175-5:2019
ISO 3175-5:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 3175-5:2019
ISO 3175-5:2019(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 2

5 Reagents ........................................................................................................................................................................................................................ 2

6 Apparatus ..................................................................................................................................................................................................................... 2

7 Conditioning .............................................................................................................................................................................................................. 3

8 Test specimen .......................................................................................................................................................................................................... 3

9 Procedure..................................................................................................................................................................................................................... 3

9.1 General ........................................................................................................................................................................................................... 3

9.2 Procedure for normal materials ............................................................................................................................................... 4

9.3 Procedures for sensitive materials ........................................................................................................................................ 5

10 Test report ................................................................................................................................................................................................................... 5

Bibliography ................................................................................................................................................................................................................................ 7

© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 3175-5:2019
ISO 3175-5:2019(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/iso/foreword .html.

This document was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee SC 2, Cleansing,

finishing and water resistance tests.
A list of all parts in the ISO 3175 series can be found on the ISO website.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 3175-5:2019
ISO 3175-5:2019(E)
Introduction

Drycleaning is a process for cleaning textiles in an organic solvent that dissolves oils and fats and

disperses particulate dirt substantially without the swelling and creasing associated with washing or

wet cleaning. Small quantities of water can be incorporated in the solvent with the aid of a surfactant for

the purpose of obtaining better soil and stain removal. Some moisture-sensitive articles are preferably

drycleaned without the addition of water to the solvent. A surfactant is often used to assist with soil

removal and reduce the risk of greying, but it should be borne in mind that surfactants contain varying

amounts of water in their formulations.

Drycleaning is normally followed by an appropriate restorative finishing procedure. In most cases, this

comprises some form of steam treatment and/or hot pressing.

Properties of the textile or garment may change progressively on drycleaning and steaming and/or

pressing and in some cases a single treatment can give little indication of the extent of dimensional

and other changes that can arise after repeated treatments and which can affect the useful life of the

article. Generally, most of the potential changes become apparent after three to five of the d

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.