EN 14420-6:2013
(Main)Hose fittings with clamp units - Part 6: TW tank truck couplings
Hose fittings with clamp units - Part 6: TW tank truck couplings
This European Standard specifies the fitting combinations, design, materials and dimensions for hose fittings with couplings for tank trucks (TW couplings).
Couplings for tank trucks in accordance with this document are intended to link hoses with connections for the transport of liquids, solid matters and gases with the exception of liquid gas and steam. They can be employed in a working pressure range of -0,8 bar up to 16 bar at working temperatures of -20 °C up to +65 °C. Couplings for tank trucks for other operating conditions are subject to agreement.
WARNING - Male and female dust couplings are pressure resistant plugs. They do not fulfil the function of a locking device, which should be installed in any case as long as the hose assembly is under pressure.
Schlaucharmaturen mit Klemmfassungen - Teil 6: TW Tankwagen-Kupplungen
Diese Europäische Norm legt die Armaturenkombinationen, Konstruktion, Werkstoffe und Maße für Schlaucharmaturen mit Kupplungen für Tankwagen (TW-Kupplungen) fest.
Kupplungen für Tankwagen nach diesem Dokument dienen der Verbindung von Schläuchen mit Anschlüssen zum Fördern von Flüssigkeiten, Feststoffen und Gasen, ausgenommen Flüssiggas und Dampf. Die Kupplungen können in einem Arbeitsdruckbereich von –0,8 bar ) bis 16 bar bei Arbeitstemperaturen von – 20 °C bis 65 °C verwendet werden. Tankwagen-Kupplungen für andere Betriebsbedingungen nach Vereinbarung.
WARNUNG — Vater- und Mutterteil-Blindkupplungen sind druckbeständige Verschlüsse. Sie über-nehmen nicht die Funktion eines Absperrorgans, das in jedem Fall vorgeschaltet sein sollte, solange die Schlauchleitungen unter Druck stehen.
Raccords pour flexibles avec demi-coquille - Partie 6: Raccords TW pour camion-citerne
La présente Norme européenne spécifie les combinaisons de raccordement, la conception, les matériaux et les dimensions des raccords pour flexibles avec raccordements pour camions-citernes (raccords TW).
Les raccordements pour camions-citernes conformes au présent document sont destinés à relier les tuyaux munis de raccordements pour le transport de liquides, de matières solides et de gaz, à l'exception des gaz liquéfiés et de la vapeur. Ils peuvent être utilisés dans une plage de pression de service de 0,8 bar ) à 16 bar pour des températures de service de 20 °C à 65 °C. Les raccordements pour camions-citernes utilisés dans d'autres conditions de service font l'objet d'un accord.
AVERTISSEMENT Les raccordements anti-poussière mâles et femelles sont des capuchons résistant à la pression. Ils ne remplissent pas la fonction d'un dispositif de verrouillage, qu’il convient d’installer dans tous les cas, tant que l’assemblage flexible est sous pression.
Cevni fitingi z objemkami - 6. del: Spojke za TW cisterne
Ta evropski standard določa kombinacije, načrtovanje, materiale in dimenzije fitingov za cevne fitinge s spojkami za TW cisterne. V skladu s tem dokumentom so spojke za TW cisterne namenjene povezovanju cevi s priključki za prevoz tekočin, trdnih snovi in plinov, razen tekočega plina in pare. Uporabljajo se lahko pri delovnem tlaku od -0,8 bara1) do 16 barov pri delovni temperaturi od -20 °C do +65 °C. Glede spojk za TW cisterne za delovanje pod drugačnimi obratovalnimi razmerami se je treba dogovoriti.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni fitingi z objemkami - 6. del: Spojke za TW cisterneSchlaucharmaturen mit Klemmfassungen - Teil 6: TW Tankwagen-KupplungenRaccords pour flexibles avec demi-coquille - Partie 6: Raccords TW pour camion-citerneHose fittings with clamp units - Part 6: TW tank truck couplings23.040.60Prirobnice, oglavki in spojni elementiFlanges, couplings and jointsICS:Ta slovenski standard je istoveten z:EN 14420-6:2013SIST EN 14420-6:2013en,fr,de01-september-2013SIST EN 14420-6:2013SLOVENSKI
STANDARDSIST EN 14420-6:2005+A1:20071DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14420-6
July 2013 ICS 23.040.70 Supersedes EN 14420-6:2004+A1:2007English Version
Hose fittings with clamp units - Part 6: TW tank truck couplings Raccords pour flexibles avec demi-coquille - Partie 6: Raccords TW pour camion-citerne
Schlaucharmaturen mit Klemmfassungen - Teil 6: TW Tankwagen-Kupplungen This European Standard was approved by CEN on 15 May 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14420-6:2013: ESIST EN 14420-6:2013
Gauges for TW tank truck couplings . 34 A.1 General . 34 A.2 Design; designation, dimensions and materials . 34 A.3 Marking . 49 Bibliography . 50
1) 1 bar = 0,1 MPa. SIST EN 14420-6:2013
4 Fitting combinations Hose fittings with TW coupling: Female coupling (Type MKS) and male coupling (Type VKS).
Usual fitting combination for the filling of the storage tank: Female coupling (Type MK) and male coupling (Type VK). Usual fitting combination for closing off the outlet end of the TW: Female coupling (Type MK) and male dust coupling (Type VB). Usual fitting combination for closing off the filling nozzle or the storage tank: Female dust coupling (Type MB) and male coupling (Type VK). 5 Dimensions, designations 5.1 Hose fittings with TW couplings 5.1.1 General A hose fitting with TW coupling for female coupling (type MKS) is shown in Figure 1. A hose fitting with TW coupling for male coupling (type VKS) is shown in Figure 2. A parts list for Figure 1 and Figure 2 is given in Table 1. SIST EN 14420-6:2013
Figure 1 — Hose fitting with TW coupling for female coupling (type MKS) Figure 2 — Hose fitting with TW coupling for male coupling (type VKS) Table 1 — Parts list Item No. Designation Requirements 1
Tension ring with levers
according to 5.3.4.2 and 5.3.4.3 2
Main gasket
according to 5.3.4.4 3
Hose tail type MKST
according to 5.1.2 4
Clamp unit
according to EN 14420-3 5
Hose tail type VKST
according to 5.1.3 6
Protecting ring
according to 5.1.4 Designation of a complete hose fitting shall be according to EN 14420-1. 5.1.2 Hose tail with female TW coupling Dimensions for a hose tail with female TW coupling (type MKST) are shown in Figure 3; values are given in Table 2. SIST EN 14420-6:2013
Key a Coupling side part of the tail; other dimensions and specifications according to 5.3. b Hose side part of the tail; dimensions according to EN 14420-2. Figure 3 — Hose tail type MKST Table 2 — Hose tail type MKST Dimensions in millimetres Nominal size
DN For hose internal
diameter l1 l2 l3 Connection female TW coupling Hose connection min. max. 10+ 50 40 38 68 24 26 50 50 75 — 80 65 63
98 27 35 80 75 102 35 100 100 100 125 27 35,5
Example for an ordering designation of a complete hose tail with female TW coupling (type MKST) with nominal size DN 50 on coupling connection side and nominal size DN 40 on hose connecting side, made of copper-zinc alloy (CW614N): Hose tail EN 14420-6 — MKST — 50 — 40 — CW614N 5.1.3 Hose tail with male TW
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.