EN 4834:2018

Aerospace series - Adaptor, Pipe coupling 24° Cone up to 35 000 kPa (5 080 psi) Port for Ring locked fitting - Inch Series - Geometric configuration

This standard specifies the dimensions, tolerances and requirements of a port for a fluid connection with ring locked fitting, for use in aircraft systems at nominal operating pressure of 35 000 kPa (5 080 psi) maximum and temperature range of −54 to +135 °C (−65 to +275 °F).

Luft- und Raumfahrt - Adapter, Rohrverschraubung 24° Konus bis 35 000 kPa (5 080 psi) Einschraublöcher für gerade Anschlussverschraubung mit Sicherungsring - Inch-Reihe - Konstruktionsblatt

Diese Europäische Norm legt Abmessungen, Toleranzen und Anforderungen an Einschraublöcher für eine
Flüssigkeitsverbindung für gerade Anschlussverschraubungen mit Sicherungsring zur Verwendung in Flugzeugsystemen
bei maximalem Nennarbeitsdruck von 35 000 kPa (5 080 psi) und in einem Temperaturbereich
von −54 °C bis +135 °C (−65 °F bis +275 °F) fest.

Série aérospatiale - Adaptateur, Système de raccordement interface conique 24° jusqu'à 35 000 kPa (5 080 psi) Implantation pour raccord avec bague de sécurité - Série inch - Configuration géométrique

Aeronavtika - Adapter, cevni priključek 24°, konica do 35 000 kPa (5080 psi), vrata za navojni priključek z zapornim obročem - Palčne mere - Geometrijski načrt

Ta standard določa mere, odstopanja in zahteve za vrata za navojni priključek z zapornim obročem za uporabo v letalskim sistemih pri najvišjem nazivnem obratovalnem tlaku 35 000 kPa (5080 psi) in temperaturnem razponu od −54 °C do 135 °C (−65 °F do 275 °F).

General Information

• Status: Published
• Publication Date: 31-Jul-2018
• Withdrawal Date: 27-Feb-2019
• ICS: 49.080 - Aerospace fluid systems and components
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3/S 3 - Hydraulics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 01-Aug-2018
• Completion Date: 01-Aug-2018
• Ref Project: SIST EN 4834:2018 - Aerospace series - Adaptor, Pipe coupling 24° Cone up to 35 000 kPa (5 080 psi) Port for Ring locked fitting - Inch Series - Geometric configuration

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2018
$HURQDYWLND$GDSWHUFHYQLSULNOMXþHNƒNRQLFDGRN3DSVLYUDWD
]DQDYRMQLSULNOMXþHN]]DSRUQLPREURþHP3DOþQHPHUH*HRPHWULMVNLQDþUW
Aerospace series - Adaptor, Pipe coupling 24° Cone up to 35 000 kPa (5 080 psi) Port
for Ring locked fitting - Inch Series - Geometric configuration
Luft- und Raumfahrt - Adapter, Rohrverschraubung 24° Konus bis 35 000 kPa (5 080
psi) Einschraublöcher für gerade Anschlussverschraubung mit Sicherungsring - Inch-
Reihe - Konstruktionsblatt
Série aérospatiale - Adapteur, Système de raccordement interface conique 24° jusqu'à
35 000 kPa (5 080 psi) Implantation pour raccord avec bague de sécurité - Série inch -
Configuration géométrique
Ta slovenski standard je istoveten z: EN 4834:2018
ICS:
49.080 /HWDOVNLLQYHVROMVNL Aerospace fluid systems and
KLGUDYOLþQLVLVWHPLLQGHOL components
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 4834
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 49.080
English Version
Aerospace series - Adaptor, Pipe coupling 24° Cone up to
35 000 kPa (5 080 psi) Port for Ring locked fitting - Inch
Series - Geometric configuration
Série aérospatiale - Adapteur, Système de Luft- und Raumfahrt - Adapter, Rohrverschraubung
raccordement interface conique 24° jusqu'à 35 000 kPa 24° Konus bis 35 000 kPa (5 080 psi) Einschraublöcher
(5 080 psi) Implantation pour raccord avec bague de für gerade Anschlussverschraubung mit
sécurité - Série inch - Configuration géométrique Sicherungsring - Inch-Reihe - Konstruktionsblatt
This European Standard was approved by CEN on 3 December 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4834:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Requirements . 6
4 Designation . 9
5 Marking . 9
6 Technical specification . 9
Bibliography . 10

European foreword
This document (EN 4834:2018) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards
shall be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
Introduction
This European Standard is co-owned standard and a functional equivalent of AS5551. There should be
no technical objection to use AS5551 as replacement of EN 4834 parts. Further revisions to this
standard shall be coordinated with the SAE committee.
European standards use the International System of units (SI); however, large segments of the
aerospace industry make use of other measurement systems as a matter of common working practice.
All dimensions and units used in this standard are given in SI units, with other units also indicated for
the convenience of the user.
The decimal sign used in European standards is the comma (“,”); however, the comma is not used in
common working practice with non-SI dimensions. Therefore, in common with many other aerospace
standards, the decimal point (“.”) is used in this standard when providing dimensions in inch-pound
units.
NOTE The use of non-SI units and the decimal point in this standard does not constitute general acceptance
of measurement systems other than SI within European standards.
1 Scope
This European Standard specifies the dimensions, tolerances and requirements of a port for a fluid
connection with ring locked fitting, for use in aircraft systems at nominal operating pressure of
35 000 kPa (5 080 psi) maximum and temperature range of −54 to +135 °C (−65 to +275 °F).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
EN 2815
...