EN ISO 13056:2018
(Main)Plastics piping systems - Pressure systems for hot and cold water - Test method for leaktightness under vacuum (ISO 13056:2011)
Plastics piping systems - Pressure systems for hot and cold water - Test method for leaktightness under vacuum (ISO 13056:2011)
This International Standard specifies a method for testing the leaktightness under vacuum of joints for
thermoplastics piping systems.
It is applicable to piping systems based on thermoplastics pipes intended to be used in hot and cold water
pressure applications.
Kunststoff-Rohrleitungssysteme - Drucksysteme für Warm- und Kaltwasser - Prüfverfahren der Vakuumdichtheit (ISO 13056:2011)
Systèmes de canalisations en plastique - Systèmes pour installation d'eau chaude et froide sous pression - Méthode d'essai de l'étanchéité sous vide (ISO 13056:2011)
La présente Norme internationale spécifie une méthode d'essai de l'étanchéité sous vide des assemblages
pour les systèmes de canalisations thermoplastiques.
Elle s'applique aux systèmes de canalisations constitués de tubes thermoplastiques destinés à être utilisés
pour des installations sous pression d'eau chaude et froide.
Cevni sistemi iz polimernih materialov - Tlačni sistemi za toplo in hladno vodo - Preskusna metoda za ugotavljanje tesnosti pod podtlakom (ISO 13056:2011)
Ta mednarodni standard opredeljuje metodo za preskušanje tesnosti spojev sistemov termoplastičnih cevi pod podtlakom. Uporablja se za sisteme s termoplastičnimi cevmi, namenjene za uporabo s tlačnimi sistemi za toplo in hladno vodo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13056:2018
01-december-2018
1DGRPHãþD
SIST EN 12294:2000
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY7ODþQLVLVWHPL]DWRSORLQKODGQRYRGR
3UHVNXVQDPHWRGD]DXJRWDYOMDQMHWHVQRVWLSRGSRGWODNRP ,62
Plastics piping systems - Pressure systems for hot and cold water - Test method for
leaktightness under vacuum (ISO 13056:2011)
Kunststoff-Rohrleitungssysteme - Drucksysteme für Warm- und Kaltwasser -
Prüfverfahren der Vakuumdichtheit (ISO 13056:2011)
Systèmes de canalisations en plastique - Systèmes pour installation d'eau chaude et
froide sous pression - Méthode d'essai de l'étanchéité sous vide (ISO 13056:2011)
Ta slovenski standard je istoveten z: EN ISO 13056:2018
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 13056:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13056:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 13056:2018
EN ISO 13056
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 23.040.01; 91.140.60 Supersedes EN 12294:1999
English Version
Plastics piping systems - Pressure systems for hot and cold
water - Test method for leaktightness under vacuum (ISO
13056:2011)
Systèmes de canalisations en plastique - Systèmes pour Kunststoff-Rohrleitungssysteme - Drucksysteme für
installation d'eau chaude et froide sous pression - Warm- und Kaltwasser - Prüfverfahren der
Méthode d'essai de l'étanchéité sous vide (ISO Vakuumdichtheit (ISO 13056:2011)
13056:2011)
This European Standard was approved by CEN on 1 October 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13056:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13056:2018
EN ISO 13056:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13056:2018
EN ISO 13056:2018 (E)
European foreword
The text of ISO 13056:2011 has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 13056:2018 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12294:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slova
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.