iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

FprEN 14336

(Main)

Heating systems in buildings - Installation and commissioning of water based heating systems

Heating systems in buildings - Installation and commissioning of water based heating systems

This document specifies the requirements for the installation and commissioning of water-based heating, water-based cooling, and heating of domestic hot water (DHW) systems in buildings with a maximum operating temperature of 105 °C.
This document is applicable to the commissioning of systems as a whole, in cases of new systems, renovations and replacement of equipment.
This document does not apply to superheated water systems or steam systems and it does not apply to the specific commissioning requirements for individual components (e.g. how to set fuel/air ratio on a burner). Also, it does not apply to the installation or commissioning of attached systems (e.g. air conditioning, domestic hot water distribution, ventilation systems).
This document specifies only technical requirements but it does not specify any commercial or contractual arrangements between parties.

Heizungsanlagen in Gebäuden - Installation und Abnahme der Warmwasser - Heizungsanlagen

Dieses Dokument legt die Anforderungen an die Installation und Abnahme wassergeführter Heizungs- und wassergeführter Kühlanlagen sowie häusliche Anlagen zur Erwärmung von Warmwasser (DHW) in Gebäuden mit einer maximalen Betriebstemperatur von 105 °C fest.
Dieses Dokument behandelt keine Heißwasser- und Heißdampfsysteme.
Dieses Dokument behandelt die Abnahme der Anlage als Ganzes bei neuen Anlagen, Renovierungen und Austausch der Geräte. Es behandelt nicht die spezifischen Abnahmeanforderungen für diese Komponenten (z. B. Einstellen des Brennstoff-Luft-Verhältnisses an einem Brenner).
Dieses Dokument gilt nicht für die Installation und die Abnahme von zugeschalteten Anlagen (z. B. Klimaanlagen, Hauswasseranlagen, Verteileranlagen, Lüftungsanlagen).
Dieses Dokument legt nur die technischen Voraussetzungen fest und regelt nicht das vertragliche Verhältnis zwischen Auftraggeber und Auftragnehmer (Planer und Ausführenden).

Systèmes de chauffage dans les bâtiments - Installation et commissionnement des systèmes de chauffage à eau

Le présent document spécifie les exigences relatives à l’installation et au commissionnement des systèmes de chauffage à eau, des systèmes de refroidissement à eau, et des systèmes de production d’eau chaude sanitaire des bâtiments fonctionnant avec une température maximale de 105 °C.
Le présent document ne couvre pas les systèmes d’eau surchauffée et les systèmes à vapeur.
Le présent document couvre le commissionnement du système dans son ensemble, en cas d’installation de nouveaux systèmes, de rénovations, de remplacement d’un équipement. Il ne concerne pas les opérations de commissionnement spécifiques à ces composants (par exemple, comment régler le rapport air/combustible au niveau d’un brûleur).
Le présent document ne couvre pas l’installation ou le commissionnement des systèmes connexes (par exemple, systèmes de conditionnement d’air, de production d’eau chaude sanitaire, de ventilation).
Le présent document couvre uniquement les spécifications techniques, il ne concerne pas les accords contractuels ou commerciaux entre les parties.

Ogrevalni in hladilni sistemi v stavbah - Vgradnja in zagon toplovodnih in hladilnih sistemov

General Information

Status
Not Published
Publication Date
14-May-2025
ICS
91.140.10 - Central heating systems
Technical Committee
CEN/TC 228 - Heating systems in buildings
Drafting Committee
CEN/TC 228/WG 1 - General performance requirements of heating systems and sub-systems in buildings
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
20-Nov-2024
Due Date
19-Nov-2024
Completion Date
20-Nov-2024
Ref Project
oSIST prEN 14336:2024 - Heating and cooling systems in buildings - Installation and commissioning of water based heating and cooling systems

Relations

Revises
EN 14336:2004 - Heating systems in buildings - Installation and commissioning of water based heating systems
Effective Date
05-Apr-2023

Buy Standard

prEN 14336:2024prEN 14336:2024
PreviousNext
Draft
prEN 14336:2024
English language
69 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2024
Ogrevalni in hladilni sistemi v stavbah - Vgradnja in zagon toplovodnih in hladilnih
sistemov
Heating and cooling systems in buildings - Installation and commissioning of water
based heating and cooling systems
Heizungsanlagen und wassergeführte Kühlanlagen in Gebäuden - Installation und
Abnahme der Warmwasser-Heizungsanlagen
Systèmes de chauffage dans les bâtiments - Installation et commissionnement des
systèmes de chauffage à eau
Ta slovenski standard je istoveten z: prEN 14336
ICS:
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
prEN 14336
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2024
ICS 91.140.10 Will supersede EN 14336:2004
English Version
Heating and cooling systems in buildings - Installation and
commissioning of water based heating and cooling
systems
Systèmes de chauffage dans les bâtiments - Installation Heizungsanlagen in Gebäuden - Installation und
et commissionnement des systèmes de chauffage à eau Abnahme der Warmwasser-Heizungsanlagen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 228.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14336:2024 E
worldwide for CEN national Members.

prEN 14336:2024 (E)
Contents Page
European foreword . 5
Introduction . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Installation . 10
4.1 Preparation for the installation . 10
4.1.1 Documentation . 10
4.1.2 Site preparation. 11
4.2 Inventory and inspection of incoming goods . 11
4.3 Handling of materials . 12
4.4 Storage of materials . 12
4.5 Installation of components . 12
4.5.1 General. 12
4.5.2 Heat generation . 13
4.5.3 Heat distribution – piping and pumps . 14
4.5.4 Heat emission . 14
4.5.5 Control and monitoring . 15
4.5.6 Thermal insulation . 15
4.6 Site inspections during the installation work . 16
4.7 Changes during the installation process . 16
5 Pre-functional checks . 16
5.1 Objective . 16
5.2 General check . 17
5.3 Equipment and component check . 17
5.4 Electrical checks . 18
6 Pressure test . 18
6.1 General. 18
6.2 Hydraulic test . 19
6.3 Pneumatic test . 20
6.3.1 General. 20
6.3.2 Tightness test . 21
6.3.3 Load test . 22
7 System cleaning . 22
7.1 General. 22
7.2 Simple and dynamic flushing . 22
7.2.1 General. 22
7.2.2 Simple flushing . 23
7.2.3 Dynamic flushing . 24
7.3 Mechanical cleaning . 25
7.4 Use of chemicals . 25
8 System filling and venting . 26
8.1 General. 26
8.2 Frost precautions . 26
8.3 Use of chemicals . 27
8.4 Filling report . 27
prEN 14336:2024 (E)
9 Balancing water flow rates . 27
10 Functional testing . 28
10.1 General . 28
10.2 Testing and settings of individual devices . 28
10.3 Testing the sequences of operation . 29
11 Handover . 30
11.1 Objective . 30
11.2 Documents for operation, maintenance and use . 30
11.3 Instructions on operation and use . 30
11.4 Hand over documentation . 30
Annex A (informative) List of test and control activities . 32
A.1 Introduction . 32
A.2 Contents of the list . 32
A.3 Sample list of test and control activities . 33
Annex B (informative) Installation site inspection . 35
B.1 Introduction . 35
B.2 Installation site inspection report . 35
B.3 Sample site inspection report . 36
Annex C (informative) PRE-COMMISSIONING CHECKS . 37
C.1 Introduction . 37
C.2 Equipment and major components check-lists . 37
C.2.1 Pump . 37
C.2.2 Boiler . 38
C.2.3 Heat pump . 40
C.2.4 Fan-coil unit . 41
C.2.5 Control valves .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17956:2024(Main)
Energy efficiency classes for technical insulation systems - Calculation method and applications
SIST EN 17956:2024

This document is applicable to technical insulation systems of operational installations in industry and the building services, such as pipes, ducts, vessels, equipment and built-in components.
The document specifies methods for the energy efficiency classification of insulation systems for the abovementioned components with an operational temperature range of −30 °C up to 650 °C.
The document addresses plant operators, engineers of operational installations, as well as the involved contractors such as insulation contractors and pipefitting contractors.
The design of safe surface temperatures for personal protection, as well as the prevention of condensation, is outside the scope of this document.
This document also does not apply to water-based heating and cooling systems in buildings and does not apply to directly buried district heating and district cooling pipes.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-4:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) (ISO 11855-4:2021)
SIST EN ISO 11855-4:2021

This document allows the calculation of peak cooling capacity of Thermo Active Building Systems (TABS) – Type V according to ISO 11855-1, based on heat gains, such as solar gains, internal heat gains, and ventilation, and the calculation of the cooling power demand on the water side, to be used to size the cooling system, as regards, e.g. the chiller size, fluid flow rate.
This document defines a detailed method aimed at the calculation of heating and cooling capacity in non-steady state conditions.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-3:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 3: Design and dimensioning (ISO 11855-3:2021)
SIST EN ISO 11855-3:2021

This document establishes a system design and dimensioning method to ensure the heating and cooling capacity of the radiant heating and cooling systems.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-5:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 5: Installation (ISO 11855-5:2021)
SIST EN ISO 11855-5:2021

This document establishes requirements for the installation of embedded radiant heating and cooling systems. It specifies general and uniform requirements for the design and construction of heating and cooling floors, ceiling and wall structures to ensure that the heating/cooling systems are suited to the particular application. The requirements specified by this document are applicable only to the components of the heating/cooling systems and the elements which are part of the heating/cooling surface and which are installed due to the heating/cooling systems.
This document is applicable to water-based embedded surface heating and cooling systems in residential, commercial and industrial buildings. The methods apply to systems integrated into the wall, floor or ceiling construction without any open-air gaps, but are not applicable to panel systems with open-air gaps which are not integrated into the building structure.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-1:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 1: Definitions, symbols, and comfort criteria (ISO 11855-1:2021)
SIST EN ISO 11855-1:2021

This document specifies the basic definitions, symbols, and comfort criteria for embedded radiant heating and cooling systems.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15316-4-2:2017/AC:2017(Corrigendum)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
SIST EN 15316-4-2:2018/AC:2018
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12831-1:2017(Main)
Energy performance of buildings - Method for calculation of the design heat load - Part 1: Space heating load, Module M3-3
SIST EN 12831-1:2018

This European Standard covers methods for the calculation of the design heat load for single rooms, building entities and buildings, where the design heat load is defined as the heat supply (power) needed to maintain the required internal design temperature under design external conditions.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000 -1.
NOTE 1   In CEN ISO/TR 52000 2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
(...)

  • Standard
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12831-3:2017(Main)
Energy performance of buildings - Method for calculation of the design heat load - Part 3: Domestic hot water systems heat load and characterisation of needs, Module M8-2, M8-3
SIST EN 12831-3:2018

This European Standard describes a method to calculate the power and the storage volume required for the dimensioning of domestic hot water systems (DHW). The applicability ranges from direct water heaters (no storage volume and a comparatively large effective heating power) to larger storage systems with a comparatively small heating power and large storage volumes.
This European Standard is applicable to the following water storage systems:
-   storage systems characterized by a minimal mixing zone, (such as stratified charging storage tanks or storage tanks with external heat exchangers): these systems are nominated in this standard as "charging storage systems";
-   storage tank water heaters and warm water storage tanks with a pronounced mixing zone (such as DHW storage tanks with internal heat exchangers), nominated in this standard as "mixed storage systems";
and for different uses.
The Scope also includes standardization methods for determining the energy need for domestic hot water. This European Standard covers the domestic hot water needs in buildings.
The calculation of the energy needs for DHW-Systems applies to residential and non-residential buildings, a building or a zone of a building.
Figure 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000-1.
NOTE 1   In CEN ISO/TR 52000-2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
Table 1 shows the relative position of this standard within the EPB package of standards.
(...)

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15459-1:2017(Main)
Energy performance of buildings - Economic evaluation procedure for energy systems in buildings - Part 1: Calculation procedures, Module M1-14
SIST EN 15459-1:2018

This European Standard provides a calculation method for the economic issues of heating systems and other systems that are involved in the energy demand and consumption of the building. It applies to all types of new and existing buildings.
The fundamental principles and terminology are explained in the standard.
The main items of the standard will be:
-   the definitions and the structure of the types of costs which should be taken into account for the calculation of the economic efficiency of saving options in buildings;
-   data needed for definition of costs related to systems under consideration;
-   the calculation method(s);
-   expression of the result of the economic study.
This European Standard is part of the method for calculation of economic performance of energy saving options in buildings (e.g. insulation, better performing generators and distribution systems, efficient lighting, renewable sources, combined heat and power...).
The scope of this specific part is to standardize:
-   the required inputs;
-   the required outputs;
-   the calculation formulas;
-   the type of energy systems concerned with the energy performance of the building.
NOTE 1   This is the revision of EN 15459:2007. The revision has been made consistent with the EU regulation on cost-optimal. This revision includes the definition of payback for investment, and inclusion of the costs due to the deconstruction of the building. The method presenting annualized costs has been suppressed.
NOTE 2   This standard does not consider financial advantages for higher productivity, higher attractiveness for tenants due to higher indoor comfort, when relevant for comparison of different options.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000-1.
NOTE 3   In CEN ISO/TR 52000-2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 4   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
(...)

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15316-4-5:2017(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-5: District heating and cooling, Module M3-8-5, M4-8-5, M8-8-5, M11-8-5
SIST EN 15316-4-5:2018

This European Standard defines the determination of energy indicators of district energy systems. District energy systems may be district heating, district cooling or other district energy carriers.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in prEN ISO 52000 1.
NOTE 1   In prCEN ISO/TR 52000 2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2    The modules represent EPB standards, although one EPB more than one module and one module may be covered by more than one EPB standard, for instance a standard may cover a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
(Table 1 - Position of EN 15316-4-5 within the modular structure)
....

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day