EN ISO 23278:2009
(Main)Non-destructive testing of welds - Magnetic particle testing of welds - Acceptance levels (ISO 23278:2006)
Non-destructive testing of welds - Magnetic particle testing of welds - Acceptance levels (ISO 23278:2006)
ISO 23278:2006 specifies acceptance levels for indications from imperfections in ferromagnetic steel welds detected by magnetic particle testing.
The acceptance levels in ISO 23278:2006 are primarily intended for use during manufacture examination, but where appropriate they can be used for in-service inspection.
These acceptance levels can be related to welding standards, application standards, specifications or codes.
Zerstörungsfreie Prüfung von Schweißverbindungen - Magnetpulverprüfung von Schweißverbindungen - Zulässigkeitsgrenzen (ISO 23278:2006)
Diese Internationale Norm legt Zulässigkeitsgrenzen für Anzeigen von Unregelmäßigkeiten in ferromagnetischen Stahlschweißverbindungen fest, die mit der Magnetpulverprüfung nachgewiesen werden.
Die Zulässigkeitsgrenzen sind hauptsächlich für die Anwendung während der Herstellung vorgesehen, können aber auch bei der Betriebsprüfung angewendet werden, wenn es angemessen ist.
Die Zulässigkeitsgrenzen in dieser Internationalen Norm beruhen auf der Auffindbarkeit, die erwartet werden kann, wenn die Techniken nach ISO 17638 und die im Anhang A empfohlenen Prüfparameter verwendet werden. Die Zulässigkeitsgrenzen nach dieser Norm können sich auf Schweißnormen, Anwendungsnormen, Spezifikationen oder Codes beziehen. Eine solche Beziehung ist in ISO 17635 für ISO 5817 aufgezeigt.
Contrôle non destructif des assemblages soudés - Contrôle par magnétoscopie des soudures - Niveaux d'acceptation (ISO 23278:2006)
L'ISO 23278:2006 spécifie les niveaux d'acceptation pour les indications des défauts mis en évidence sur des soudures en aciers ferromagnétiques lors du contrôle par magnétoscopie.
Les niveaux d'acceptation de l'ISO 23278:2006 sont essentiellement destinés à être utilisés pour le contrôle de fabrication, mais ils peuvent également, le cas échéant, servir pour le contrôle en service.
Ces niveaux d'acceptation peuvent être reliés à des normes de soudage, des normes d'application, des spécifications ou des codes.
Neporušitveno preskušanje zvarnih spojev - Preskušanje zvarnih spojev z magnetnimi delci - Stopnje sprejemljivosti (ISO 23278:2006)
Ta mednarodni standard določa stopnje sprejemljivosti za indikacije nepravilnosti v zvarih feromagnetnega jekla, ki se detektirajo s preskušanjem z magnetnimi delci. Stopnje sprejemljivosti so namenjene predvsem uporabi pri proizvodnih pregledih, po potrebi pa se lahko uporabijo tudi za nadzor med obratovanjem. Stopnje sprejemljivosti v tem mednarodnem standardu temeljijo na detekcijskih zmogljivostih, ki jih lahko pričakujemo pri uporabi tehnik, navedenih v ISO 17638, in parametrov, ki jih priporoča Dodatek A. Stopnje sprejemljivosti se lahko nanašajo na standarde varjenja, standarde uporabe, specifikacije ali šifre. Takšen odnos je prikazan v ISO 17635 za ISO 5817.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Neporušitveno preskušanje zvarnih spojev - Preskušanje zvarnih spojev z magnetnimi delci - Stopnje sprejemljivosti (ISO 23278:2006)Zerstörungsfreie Prüfung von Schweißverbindungen - Eindringprüfung von Schweißverbindungen - Zulässigkeitsgrenzen (ISO 23278:2006)Contrôle non destructif des assemblages soudés - Contrôle par magnétoscopie des soudures - Niveaux d'acceptation (ISO 23278:2006)Non-destructive testing of welds - Magnetic particle testing of welds - Acceptance levels (ISO 23278:2006)25.160.40Varjeni spoji in variWelded jointsICS:Ta slovenski standard je istoveten z:EN ISO 23278:2009SIST EN ISO 23278:2010en,fr,de01-april-2010SIST EN ISO 23278:2010SLOVENSKI
STANDARDSIST EN 1291:1999/A2:2004SIST EN 1291:1999/A1:2003SIST EN 1291:19991DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 23278
November 2009 ICS 25.160.40 Supersedes EN 1291:1998English Version
Non-destructive testing of welds - Magnetic particle testing of welds - Acceptance levels (ISO 23278:2006)
Contrôle non destructif des assemblages soudés -Contrôle par magnétoscopie des soudures - Niveaux d'acceptation (ISO 23278:2006)
Zerstörungsfreie Prüfung von Schweißverbindungen - Magnetpulverprüfung von Schweißverbindungen - Zulässigkeitsgrenzen (ISO 23278:2006) This European Standard was approved by CEN on 24 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 23278:2009: ESIST EN ISO 23278:2010
Reference numberISO 23278:2006(E)© ISO 2006
INTERNATIONAL STANDARD ISO23278First edition2006-10-01Non-destructive testing of welds — Magnetic particle testing of welds — Acceptance levels Contrôle non destructif des assemblages soudés — Contrôle par magnétoscopie des soudures — Niveaux d'acceptation
ISO 23278:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 23278:2006(E) © ISO 2006 – All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules gi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.