iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12513:2000

(Main)

Founding - Abrasion resistant cast irons

Founding - Abrasion resistant cast irons

This European Standard defines the grades of abrasion resistant white cast irons. It also specifies the grades in terms of: - chemical composition - hardness. The types of abrasion resistant white cast irons covered by this standard are: a) unalloyed or low cast irons; b) nickel chromium cast irons covering two general types: - 4 % Ni 2 % Cr cast irons; - 9 % Cr 5 % Ni cast irons; c) high chromium cast irons covering four ranges of chromium content.

Gießereiwesen - Verschleißbeständige Gusseisen

Diese Europäische Norm legt die Sorten von verschleissfestem weissem Gusseisen fest. Die Sorten werden ferner bestimmt durch die -chemische Zusammensetzung; -Härte. Die in dieser Norm behandelten Arten von verschleissfestem weissem Gusseisen sind: a) unlegierte oder niedriglegierte Gusseisen; b) Chrom-Nickel- Gusseisen in zwei allgemeinen Arten: -Gusseisen mit 4% Ni 2% Cr; -Gusseisen mit 9% Cr 5% Ni; c) Gusseisen mit hohem Chromgehalt umfassen vier Bereiche je nach Chromgehalt.

Fonderie - Fontes résistant à l'usure par abrasion

La présente norme européenne définit les nuances de fontes blanches résistant à l'usure par abrasion. Elle spécifie également les nuances en terme de: - composition chimique; - dureté. Les types de fontes blanches résistant à l'usurepar abrasion traités dans la présente norme sont: a) les fontes non-alliées ou faiblement alliées; b) les fontes au nickel-chrome de 2 catégories générales: -fontes à 4% Ni -2% Cr; -fontes à 9% Cr - 5% Ni; c) les fontes à haute teneur en chrome réparties en 4 gammes de teneur.

Livarstvo - Lito železo, odporno proti obrabi

General Information

Status
Withdrawn
Publication Date
17-Oct-2000
Withdrawal Date
15-Feb-2011
ICS
77.080.10 - Irons
Technical Committee
CEN/TC 190 - Foundry technology
Drafting Committee
CEN/TC 190/WG 8 - High alloyed cast iron
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
16-Feb-2011
Completion Date
16-Feb-2011
Ref Project
SIST EN 12513:2001 - Founding - Abrasion resistant cast irons

Relations

Replaced By
EN 12513:2011 - Founding - Abrasion resistant cast irons
Effective Date
08-Jun-2022

Buy Standard

EN 12513:2001EN 12513:2001
PreviousNext
Standard
EN 12513:2001
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Livarstvo - Lito železo, odporno proti obrabiGießereiwesen - Verschleißbeständige GusseisenFonderie - Fontes résistant a l'usure par abrasionFounding - Abrasion resistant cast irons77.080.10ŽelezoIronsICS:Ta slovenski standard je istoveten z:EN 12513:2000SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16079:2023(Main)
Founding - Compacted (vermicular) graphite cast irons
SIST EN 16079:2024

This document defines the grades and the corresponding requirements for compacted (vermicular) graphite cast irons.
This document specifies 4 grades of compacted (vermicular) graphite cast iron by a classification based on the minimum mechanical properties measured on machined test pieces prepared from cast samples or samples cut from a casting.
This document does not cover technical delivery conditions for iron castings (see EN 1559-1 [1] and EN 1559-3 [2]).

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1561:2023(Main)
Founding - Grey cast irons
SIST EN 1561:2024

This document specifies the properties of unalloyed and low-alloyed grey cast irons used for castings, which have been manufactured in sand moulds or in moulds with comparable thermal behaviour.
NOTE   This document can also be applicable to grey cast irons cast in permanent moulds, provided the related cast samples are casted under the same conditions as the castings.
This document specifies the characterizing properties of grey cast irons by either
a)   the tensile strength of cast samples,
b)   if agreed by the manufacturer and the purchaser, the tensile strength of samples cut from a casting,
c)   the hardness determined on the castings or on a cast-on knob.
If agreed by the manufacturer and the purchaser, the combination of both tensile strength from option a) and hardness from option c) may be specified.
This document specifies six grades of grey cast iron by a classification based on tensile strength determined on machined test pieces prepared from cast samples (see Table 1) and six grades of grey cast iron by a classification based on Brinell hardness (see Table 2).
This document does not cover technical delivery conditions for iron castings; see EN 1559-1 [3] and EN 1559-3 [4].
This document does not apply to grey cast irons used for pipes and fittings according to EN 877 [5].

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 945-1:2019(Main)
Microstructure of cast irons - Part 1: Graphite classification by visual analysis (ISO 945-1:2019)
SIST EN ISO 945-1:2019

This document specifies a method of classifying the microstructure of graphite in cast irons by comparative visual analysis.
The purpose of this document is to provide information about the method of graphite classification. It is not intended to give information on the suitability of cast-iron types and grades for any particular application.
The particular material grades are specified mainly by mechanical properties and, in the case of austenitic and abrasion resistant cast irons, by their chemical composition. The interpretation of graphite form and size does not allow a statistically valid statement on the fulfilment of the requirements specified in the relevant material standard.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1562:2019(Main)
Founding - Malleable cast irons
SIST EN 1562:2019

This document defines grades and the corresponding requirements for malleable cast irons.
This document specifies five grades of whiteheart malleable cast iron and nine grades of blackheart malleable cast iron, based on mechanical properties measured on cast samples (which are test pieces).
This document specifies Brinell hardness values determined only when these values are requested by the purchaser.
This document does not cover technical delivery conditions for malleable cast iron castings. Reference should be made to EN 1559 1 [3] and EN 1559 3 [4].
This document does not cover chemical composition, except phosphorus (see Clause 6).

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1563:2018(Main)
Founding - Spheroidal graphite cast irons
SIST EN 1563:2018

This European Standard defines the grades and the corresponding requirements for spheroidal graphite cast irons.
This European Standard specifies 2 groups of spheroidal graphite cast iron grades by a classification based on mechanical properties measured on machined test pieces prepared from cast samples. The first group deals mainly with ferritic to pearlitic grades. The second group deals with solid-solution strengthened ferritic grades.
This European Standard does not cover technical delivery conditions for iron castings (see EN 1559 1 [3] and EN 1559 3 [4]).
This European Standard does not cover:
-   ausferritic spheroidal graphite cast irons which are specified in EN 1564 [7];
-   low alloyed ferritic spheroidal graphite cast irons which are specified in EN 16124 [8];
-   continuous cast iron bars which are specified in EN 16482 [7];
-   austenitic cast irons which are specified in EN 13835 [8];
-   spheroidal graphite cast irons used for pipes, fittings and their joints which are the subject of EN 545 [11], EN 598 [12] and EN 969 [13];
-   the grades of spheroidal graphite cast irons as specified in EN 545 which are used for products such as industrial valves, non-industrial manually operated shut-off valves and flanges and their joints, which are the subject of the applicable European product standards.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16482:2014(Main)
Founding - Continuous cast iron bars
SIST EN 16482:2014

This European Standard defines the grades of grey cast iron and spheroidal graphite cast iron bars, which have been produced by the continuous casting process.
This European Standard specifies the characterizing properties of grey cast iron bars by either:
a)   the tensile strength measured on machined test pieces prepared from samples cut from the bars, or
b)   the hardness measured on the bars.
If agreed by the manufacturer and the purchaser, the combination of both tensile strength from option a) and hardness from option b) may be specified.
This European Standard specifies the characterizing properties of spheroidal graphite cast iron bars by the tensile strength measured on machined test pieces prepared from samples cut from the bars.
This European Standard specifies 4 grades of grey cast iron and 14 grades of spheroidal graphite cast iron by a classification based on tensile strength and 4 grades of grey cast iron by a classification based on Brinell hardness.
This European Standard specifies also the straightness of the bars.
This European Standard does not cover technical delivery conditions for iron castings (see EN 1559 1 [1] and EN 1559 3 [2]).

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13835:2012(Main)
Founding - Austenitic cast irons
SIST EN 13835:2012

This European Standard specifies the grades and corresponding requirements for austenitic cast irons. These requirements are specified in terms of:
graphite form and metal structure: either flake or spheroidal graphite in an austenitic matrix;
chemical composition: as given for each of the grades;
mechanical properties measured on machined test pieces prepared from cast samples.
This standard does not cover technical delivery conditions for iron castings, see EN 1559-1 [1] and
EN 1559-3 [2].

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16124:2011(Main)
Founding - Low-alloyed ferritic spheroidal graphite cast irons for elevated temperature applications
SIST EN 16124:2012

This European Standard defines the grades and the corresponding requirements for low-alloyed ferritic spheroidal graphite cast irons for elevated temperature applications.
These requirements are specified in terms of
   chemical composition: as given for each of the grades,
   graphite form and metal structure: spheroidal graphite in a predominantly ferritic matrix,
   mechanical properties measured on machined test pieces prepared from cast samples.
This European Standard does not cover technical delivery conditions for iron castings, see EN 1559 1 [1] and EN 1559 3 [2].

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1564:2011(Main)
Founding - Ausferritic spheroidal graphite cast irons
SIST EN 1564:2012

This European Standard defines the grades and the corresponding requirements for ausferritic spheroidal graphite cast irons.
This European Standard specifies five grades of ausferritic spheroidal graphite cast iron by a classification based on mechanical properties measured on machined test pieces prepared from cast samples.
This European Standard also specifies two grades by a classification as a function of hardness.
This European Standard does not cover technical delivery conditions for iron castings, see EN 1559-1 [4] and EN 1559-3 [5].
NOTE   Grades given in Annex A are not intended for pressure equipment applications.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1560:2011(Main)
Founding - Designation system for cast iron - Material symbols and material numbers
SIST EN 1560:2011

This European Standard establishes a material designation system either by symbols or by numbers for cast iron.
The designation system by symbols is applicable to:
a)   standardized cast iron materials (see 2.1);
b)   non-standardized cast iron materials (see 2.2).
The designation system by numbers is only applicable to standardized cast iron materials (see 2.1).
NOTE   The use of a designation system by symbols does not necessarily imply that the material is standardized.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day