EN ISO 4014:2011
(Main)Hexagon head bolts - Product grades A and B (ISO 4014:2011)
Hexagon head bolts - Product grades A and B (ISO 4014:2011)
ISO 4014:2011 specifies the characteristics of hexagon head bolts with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or 150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or 150 mm, whichever is the shorter.
Sechskantschrauben mit Schaft - Produktklassen A und B (ISO 4014:2011)
Diese Internationale Norm legt Eigenschaften von Sechskantschrauben mit Schaft und Gewinden von M1,6
bis M64, mit Produktklasse A für Gewinde von M1,6 bis M24 und Nennlängen ≤ 10 d oder 150 mm, wobei der
kleinere Zahlenwert gilt, und mit Produktklasse B für Gewinde über M24 oder Nennlängen > 10 d oder
150 mm, wobei der kleinere Zahlenwert gilt, fest.
Falls in besonderen Fällen andere Festlegungen als die in dieser Norm aufgeführten benötigt werden, können
diese den entsprechenden ISO-Normen entnommen werden, z. B. ISO 724, ISO 888, ISO 898-1, ISO 965-1,
ISO 3506-1, ISO 4753 und ISO 4759-1.
Vis à tête hexagonale partiellement filetées - Grades A et B (ISO 4014:2011)
L'ISO 4014:2011 spécifie les caractéristiques des vis à tête hexagonale partiellement filetées de diamètre de filetage M1,6 à M64 inclus, de grade A pour les filetages de diamètre M1,6 à M24 inclus et de longueur nominale inférieure ou égale à 10d ou à 150 mm, la plus petite des deux valeurs étant retenue, et de grade B pour les filetages de diamètre supérieur à M24 ou de longueur nominale supérieure à 10d ou à 150 mm, la plus petite des deux valeurs étant retenue.
Vijaki s šestrobo glavo - Razreda izdelave A in B (ISO 4014:2011)
Ta mednarodni standard določa značilnosti vijakov s šestrobo glavo z navoji od M1,6 do vključno M64 razreda izdelave A za navoje od M1,6 do M24 in z nazivnimi dolžinami do vključno 10d ali 150 mm, kar je krajše, in razreda izdelave B za navoje nad M24 oziroma z nazivnimi dolžinami nad 10d ali 150 mm, kar je krajše.
Če so v posebnih primerih zahtevane specifikacije, drugačne od specifikacij, navedenih v tem mednarodnem standardu, se lahko izberejo izmed obstoječih mednarodnih standardov, na primer ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 in ISO 4759-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2011
1DGRPHãþD
SIST EN ISO 4014:2002
Vijaki s šestrobo glavo - Razreda izdelave A in B (ISO 4014:2011)
Hexagon head bolts - Product grades A and B (ISO 4014:2011)
Sechskantschrauben mit Schaft - Produktklassen A und B (ISO 4014:2011)
Vis à tête hexagonale partiellement filetées - Grades A et B (ISO 4014:2011)
Ta slovenski standard je istoveten z: EN ISO 4014:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 4014
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 21.060.10 Supersedes EN ISO 4014:2000
English Version
Hexagon head bolts - Product grades A and B (ISO 4014:2011)
Vis à tête hexagonale partiellement filetées - Grades A et B Sechskantschrauben mit Schaft - Produktklassen A und B
(ISO 4014:2011) (ISO 4014:2011)
This European Standard was approved by CEN on 31 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4014:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 4014:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2011, and conflicting national standards shall be
withdrawn at the latest by September 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4014:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4014:2011 has been approved by CEN as a EN ISO 4014:2011 without any modification.
INTERNATIONAL ISO
STANDARD 4014
Fourth edition
2011-03-15
Hexagon head bolts — Product grades A
and B
Vis à tête hexagonale partiellement filetées — Grades A et B
Reference number
ISO 4014:2011(E)
©
ISO 2011
ISO 4014:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 4014:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4014 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product
standards for fasteners.
This fourth edition cancels and replaces the third edition (ISO 4014:1999), of which it constitutes a minor
revision.
ISO 4014:2011(E)
Introduction
This International Standard belongs to a complete group of product standards developed by ISO on external
hexagon drive fasteners. It comprises the following:
a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042,
ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);
d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072);
e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and
ISO 21670).
iv © ISO 2011 – All rights reserved
INTERNATIONAL STANDARD ISO 4014:2011(E)
Hexagon head bolts — Product grades A and B
1 Scope
This International Standard specifies the characteristics of hexagon head bolts with threads from M1,6 up to
and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or
150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or
150 mm, whichever is the shorter.
If, in special cases, specifications other than those listed in this International Standard are required, they can
be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1,
ISO 3506-1, ISO 4753 and ISO 4759-1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
ISO 724, ISO general-purpose metric screw threads — Basic dimensions
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs with specified property classes — Coarse thread and fine pitch thread
ISO 965-1, ISO general-purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 3269, Fasteners — Acceptance inspection
ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and
studs
ISO 4017, Hexagon head screws — Product grades A and B
ISO 4042, Fasteners — Electroplated coatings
ISO 4753, Fasteners — Ends of parts with external ISO metric thread
ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements
ISO 8839, Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals
ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings
ISO 4014:2011(E)
3 Dimensions
See Figure 1 and Tables 1 and 2.
Symbols and descriptions of dimensions are specified in ISO 225.
Dimensions in millimetres
a
β = 15° to 30°.
b
Point shall be chamfered or for threads u M4 may be as-rolled (sheared end) in accordance with ISO 4753.
c
Incomplete thread u u 2P.
d
Reference datum for d .
w
e
Maximum underhead fillet.
Figure 1
2 © ISO 2011 – All rights reserved
ISO 4014:2011(E)
Table 1 — Preferred threads
Dimensions in millimetres
Thread, d M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10
a
P 0,35 0,4 0,45 0,5 0,7 0,8 1 1,25 1,5
b
9 10 11 12 14 16 18 22 26
c
b ref. 15 16 17 18 20 22 24 28 32
d
28 29 30 31 33 35 37 41 45
max. 0,25 0,25 0,25 0,40 0,40 0,50 0,50 0,60 0,60
c
min. 0,10 0,10 0,10 0,15 0,15 0,15 0,15 0,15 0,15
d max. 2 2,6 3,1 3,6 4,7 5,7 6,8 9,2 11,2
a
nom. = max. 1,60 2,00 2,50 3,00 4,00 5,00 6,00 8,00 10,00
d
A 1,46 1,86 2,36 2,86 3,82 4,82 5,82 7,78 9,78
s
Product grade min.
B 1,35 1,75 2,25 2,75 3,70 4,70 5,70 7,64 9,64
A 2,27 3,07 4,07 4,57 5,88 6,88 8,88 11,63 14,63
d Product grade min.
w
B 2,30 2,95 3,95 4,45 5,74 6,74 8,74 11,47 14,47
A 3,41 4,32 5,45 6,01 7,66 8,79 11,05 14,38 17,77
e Product grade min.
B 3,28 4,18 5,31 5,88 7,50 8,63 10,89 14,20 17,59
l max. 0,6 0,8 1 1 1,2 1,2 1,4 2 2
f
nom. 1,1 1,4 1,7 2 2,8 3,5 4 5,3 6,4
max. 1,225 1,525 1,825 2,125 2,925 3,65 4,15 5,45 6,58
Product grade A
k min. 0,975 1,275 1,575 1,875 2,675 3,35 3,85 5,15 6,22
max. 1,3 1,6 1,9 2,2 3,0 3,74 4,24 5,54 6,69
Product grade B
min. 0,9 1,2 1,5 1,8 2,6 3,26 3,76 5,06 6,11
A 0,68 0,89 1,10 1,31 1,87 2,35 2,70 3,61 4,35
e
k Product grade min.
w
B 0,63 0,84 1,05 1,26 1,82 2,28 2,63 3,54 4,28
r min. 0,1 0,1 0,1 0,1 0,2 0,2 0,25 0,4 0,4
nom. = max. 3,20 4,00 5,00 5,50 7,00 8,00 10,00 13,00 16,00
s
A 3,02 3,82 4,82 5,32 6,78 7,78 9,78 12,73 15,73
Product grade min.
B 2,90 3,70 4,70 5,20 6,64 7,64 9,64 12,57 15,57
ISO 4014:2011(E)
4 © ISO 2011 – All rights reserved
Table 1 (continued)
Dimensions in millimetres
Thread, d M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10
Product grade
f
l and l
s g
A B
l l l l l l l l l l l l l l l l l l l
s g s g s g s g s g s g s g s g s g
nom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
12 11,65 12,35 — — 1,2 3
16 15,65 16,35 — — 5,2 7 4 6 2,75 5 For sizes above the solid, bold, stepped line, ISO 4017 is recommended.
20 19,58 20,42 18,95 21,05 8 10 6,75 9 5,5 8
25 24,58 25,42 23,95 26,05 11,75 14 10,5 13 7,5 11 5 9
30 29,58 30,42 28,95 31,05 15,5 18 12,5 16 10 14 7 12
35 34,5 35,5 33,75 36,25 17,5 21 15 19 12 17
40 39,5 40,5 38,75 41,25 22,5 26 20 24 17 22 11,75 18
45 44,5 45,5 43,75 46,25 25 29 22 27 16,75 23 11,5 19
50 49,5 50,5 48,75 51,25 30 34 27 32 21,75 28 16,5 24
55 54,4 55,6 53,5 56,5 32 37 26,75 33 21,5 29
60 59,4 60,6 58,5 61,5 37 42 31,75 38 26,5 34
65 64,4 65,6 63,5 66,5 36,75 43 31,5 39
70 69,4 70,6 68,5 71,5 41,75 48 36,5 44
80 79,4 80,6 78,5 81,5 51,75 58 46,5 54
90 89,3 90,7 88,25 91,75 56,5 64
100 99,3 100,7 98,25 101,75 66,5 74
110 109,3 110,7 108,25 111,75
120 119,3 120,7 118,25 121,75
ISO 4014:2011(E)
Table 1 (continued)
Dimensions in millimetres
Thread, d M12 M16 M20 M24 M30 M36 M42 M48 M56 M64
a
P 1,75 2 2,5 3 3,5 4 4,5 5
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.