EN ISO 11073-30200:2005

Health informatics - Point-of-care medical device communication - Part 30200: Transport profile - Cable connected (ISO/IEEE 11073-30200:2004)

ISO/IEEE 11073-30200:2004 describes an IrDA-based, cable-connected local area network (LAN) for the interconnection of computers and medical devices and is suitable for new device designs, but is particularly targeted to modifications of legacy devices.
The term legacy devices refers to equipment that is
already in use in clinical facilities;in active production at the facilities of medical device manufacturers;beyond the initial stages of engineering development.

Medizinische Informatik - Kommunikation patientennaher medizinischer Geräte - Teil 30200: Transportprofil - drahtgebundene Übertragung

Informatique de santé - Communication entre dispositifs médicaux sur le site des soins - Partie 30200: Profil de transport - Connexion par câble (ISO/IEEE 11073-30200:2004)

L'ISO/IEEE 11073-30200:2004 est un réseau local (LAN) connecté par câble et basé sur le protocole IrDa pour l'interconnexion d'ordinateurs et de dispositifs médicaux. La présente norme est adaptée aux nouvelles conceptions de dispositifs, mais cible en particulier les modifications apportées aux dispositifs existants.
L'expression «dispositifs existants» désigne les équipements
       déjà utilisés dans les sites cliniques;
       en production active dans les sites de fabrication de dispositifs médicaux, ou
       ayant dépassé les étapes initiales de développement technique.

Zdravstvena informatika – Komunikacija medicinskih naprav na mestu oskrbe – 30200. del: Transportni profil – Kabelsko priključen (ISO/IEEE 11073-30200:2004)

Področje uporabe tega standarda je kabelsko priključeno lokalno omrežje (LAN) na osnovi IrDA za medomrežno povezovanje računalnikov in medicinskih naprav. Ta standard je primeren za nove modele naprav, še posebej pa je namenjen spremembam starejših naprav.
Izraz »starejše naprave« se nanaša na opremo, ki
– se že uporablja v kliničnih objektih,
– je v aktivni proizvodnji v obratih proizvajalcev medicinskih naprav ali
– ni več v začetnih fazah inženirskega razvoja.
V vseh naštetih primerih bi bilo običajno zelo težko dodati standardizirane komunikacijske zmogljivosti, če ne bi posebej pazljivo razvili ustreznega standarda.

General Information

• Status: Published
• Publication Date: 30-Aug-2005
• Withdrawal Date: 27-Feb-2006
• ICS: 35.240.80 - IT applications in health care technology
• Technical Committee: CEN/TC 251 - Medical informatics
• Drafting Committee: CEN/TC 251/WG 2 - Terminology and knowledge representation
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 31-Aug-2005
• Completion Date: 31-Aug-2005
• Ref Project: SIST EN ISO 11073-30200:2005 - Health informatics - Point-of-care medical device communication - Part 30200: Transport profile - Cable connected (ISO/IEEE 11073-30200:2004)

Relations

• Amended By: EN ISO 11073-30200:2005/A1:2015 - Health informatics - Point-of-care medical device communication - Part 30200: Transport profile - Cable connected - Amendment 1 (ISO/IEEE 11073-30200:2004/Amd 1:2015)
• Effective Date: 05-Mar-2014

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2005
=GUDYVWYHQDLQIRUPDWLND±.RPXQLNDFLMDPHGLFLQVNLKQDSUDYQDPHVWXRVNUEH±
GHO7UDQVSRUWQLSURILO±.DEHOVNRSULNOMXþHQ,62,(((
Health informatics - Point-of-care medical device communication - Part 30200: Transport
profile - Cable connected (ISO/IEEE 11073-30200:2004)
Medizinische Informatik - Kommunikation patientennaher medizinischer Geräte - Teil
30200: Transportprofil - drahtgebundene Übertragung
Informatique de santé - Communication entre dispositifs médicaux sur le site des soins -
Partie 30200: Profil de transport - Connexion par câble (ISO/IEEE 11073-30200:2004)
Ta slovenski standard je istoveten z: EN ISO 11073-30200:2005
ICS:
35.240.80 Uporabniške rešitve IT v IT applications in health care
zdravstveni tehniki technology
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11073-30200
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2005
ICS 35.240.80
English Version
Health informatics - Point-of-care medical device communication
- Part 30200: Transport profile - Cable connected (ISO/IEEE
11073-30200:2004)
Informatique de santé - Communication entre dispositifs Medizinische Informatik - Kommunikation patientennaher
médicaux sur le site des soins - Partie 30200: Profil de medizinischer Geräte - Teil 30200: Transportprofil -
transport - Connexion par câble (ISO/IEEE 11073- drahtgebundene Übertragung
30200:2004)
This European Standard was approved by CEN on 16 August 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11073-30200:2005: E
worldwide for CEN national Members.

Foreword
The text of ISO/IEEE 11073-30200:2004 has been prepared by Technical Committee ISO/TC
215 "Health informatics” of the International Organization for Standardization (ISO) and has
been taken over as EN ISO 11073-30200:2005 by Technical Committee CEN/TC 251 "Health
informatics", the secretariat of which is held by NEN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by February 2006, and conflicting national
standards shall be withdrawn at the latest by February 2006.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO/IEEE 11073-30200:2004 has been approved by CEN as EN ISO 11073-
30200:2005 without any modifications.

INTERNATIONAL
ISO/IEEE
STANDARD
11073-30200
First edition
2004-12-15
Health informatics — Point-of-care
medical device communication —
Part 30200:
Transport profile — Cable connected
Informatique de santé — Communication entre dispositifs médicaux sur le
site des soins —
Partie 30200: Profil de transport — Connection par câble
Reference number
ISO/IEEE 11073-30200:2004(E)
© ISO/IEEE 2004
ISO/IEEE 11073-30200:2004(E)
Health informatics — Point-of-care
medical device communication —
Part 30200:
Transport profile — Cable connected
Sponsor
™
IEEE 1073 Standard Committee
of the
IEEE Engineering in Medicine and Biology Society
Approved 30 January 2000
IEEE-SA Standards Board
ISO/IEEE 11073-30200:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed
or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the com-
puter performing the editing. In downloading this file, parties accept therein the responsibility of not infringing
Adobe’s licensing policy. Neither the ISO Central Secretariat nor the IEEE accepts any liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the
PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for
use by ISO member bodies and IEEE members. In the unlikely event that a problem relating to it is found, please
inform the ISO Central Secretariat or the IEEE at the address given below.
Abstract: A connection-oriented transport profile and physical layer suitable for medical device
communications in legacy devices is established. Communications services and protocols
consistent with specifications of the Infrared Data Association are defined. These communication
services and protocols are optimized for use in patient-connected bedside medical devices.
Keywords: bedside, Infrared Data Association, IrDA, legacy device, medical device, medical
device communications, MIB, patient, SNTP
This ISO/IEEE document is an International Standard and is copyright-protected by ISO and the IEEE. Except as
permitted under the applicable laws of the user’s country, neither this ISO/IEEE standard nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording
or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO or the IEEE at the addresses below.
ISO copyright office Institute of Electrical and Electronics Engineers
Case postale 56 · CH-1211 Geneva 20 Standards Association
Tel. + 41 22 749 01 11 Manager, Standards Intellectual Property
Fax + 41 22 749 09 47 445 Hoes Lane
E-mail [e-mail] P. O. Box 1331
Web www.iso.org Piscataway, NJ 08854
E-mail: [e-mail]
Web: www.ieee.org
Published 15 December 2004. Printed in the United States of America.
IEEE is a registered trademark in the U.S. Patent & Trademark Office, owned by the Institute of Electrical and Electronics
Engineers, Incorporated.
Print: ISBN 0-7381-4519-X SH95303
PDF: ISBN 0-7381-4520-3 SS95303
No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior
written permission of the publisher.
ii Copyright © 2004 ISO/IEEE. All rights reserved.

ISO/IEEE 11073-30200:2004(E)
IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating Committees of the
IEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its standards through a consensus develop-
ment process, approved by the American National Standards Institute, which brings together volunteers representing varied
viewpoints and interests to achieve the final product. Volunteers are not necessarily members of the Institute and serve with-
out compensation. While the IEEE administers the process and establishes rules to promote fairness in the consensus devel-
opment process, the IEEE does not independently evaluate, test, or verify the accuracy of any of the information contained
in its standards.
Use of an IEEE Standard is wholly voluntary. The IEEE disclaims liability for any personal injury, property or other dam-
age, of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting
from the publication, use of, or reliance upon this, or any other IEEE Standard document.
The IEEE does not warrant or represent the accuracy or content of the material contained herein, and expressly disclaims
any express or implied warranty, including any implied warranty of merchantability or fitness for a specific purpose, or that
the use of the material contained herein is free from patent infringement. IEEE Standards documents are supplied “AS IS.”
The existence of an IEEE Standard does not imply that there are no other ways to produce, test, measure, purchase, market,
or provide other goods and services related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at the
time a standard is approved and issued is subject to change brought about through developments in the state of the art and
comments received from users of the standard. Every IEEE Standard is subjected to review at least every five years for revi-
sion or reaffirmation. When a document is more than five years old and has not been reaffirmed, it is reasonable to conclude
that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check
to determine that they have the latest edition of any IEEE Standard.
In publishing and making this document available, the IEEE is not suggesting or rendering professional or other services
for, or on behalf of, any person or entity. Nor is the IEEE undertaking to perform any duty owed by any other person or
entity to another. Any person utilizing this, and any other IEEE Standards document, should rely upon the advice of a com-
petent professional in determining the exercise of reasonable care in any given circumstances.
Interpretations: Occasionally questions may arise regarding the meaning of portions of standards as they relate to specific
applications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiate action to prepare
appropriate responses. Since IEEE Standards represent a consensus of concerned interests, it is important to ensure that any
interpretation has also received the concurrence of a balance of interests. For this reason, IEEE and the members of its soci-
eties and Standards Coordinating Committees are not able to provide an instant response to interpretation requests except in
those cases where the matter has previously received formal consideration. At lectures, symposia, seminars, or educational
courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered
the personal views of that individual rather than the formal position, explanation, or interpretation of the IEEE.
Comments for revision of IEEE Standards are welcome from any interested party, regardless of membership affiliation with
IEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate
supporting comments. Comments on standards and requests for interpretations should be addressed to:
Secretary, IEEE-SA Standards Board
445 Hoes Lane
P.O. Box 1331
Piscataway, NJ 08855-1331USA
NOTE — Attention is called to the possibility that implementation of this standard may require use of subject
matter covered by patent rights. By publication of this standard, no position is taken with respect to the exist-
ence or validity of any patent rights in connection therewith. The IEEE shall not be responsible for identifying
patents for which a license may be required by an IEEE standard or for conducting inquiries into the legal valid-
ity or scope of those patents that are brought to its attention.
Authorization to photocopy portions of any individual standard for internal or personal use is granted by the Institute of
Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center. To
arrange for payment of licensing fee, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive,
Danvers, MA 01923 USA; [phone]. Permission to photocopy portions of any individual standard for educational
classroom use can also be obtained through the Copyright Clearance Center.
ISO/IEEE 11073-30200:2004(E)
iv Copyright © 2004 ISO/IEEE. All rights reserved.

ISO/IEEE 11073-30200:2004(E)
ISO Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has
been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates
closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical
standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for
voting. Publication as an International Standard requires approval by at least 75% of the member bodies
casting a vote.
A pilot project between ISO and the IEEE has been formed to develop and maintain
...