iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1459:1998

(Main)

Safety of industrial trucks - Self-propelled variable reach trucks

Safety of industrial trucks - Self-propelled variable reach trucks

This standard applies to self-propelled seated rider operated variable reach trucks intended to handle loads of all kinds using one of the attachments listed in 3.10 - 3.11 - 3.13 - 3.14 - 3.15 - 3.16 - 3.19 - 3.20. It does not cover the lifting of persons by any attachments, in particular by work platforms. Machines with variable length load suspension elements (chains, ropes etc) from which the load may swing freely in all directions are not covered in this standard.

Sicherheit von Flurförderzeugen - Kraftbetriebene Stapler mit veränderlicher Reichweite

Diese Norm gilt für kraftbetriebene Mitfahrer-Flurförderzeuge mit veränderlicher Reichweite, zur Handhabung unterschiedlicher Lasten mit Hilfe von Anbaugeräten, wie sie z. B. in 3.10 - 3.11 - 3.13 - 3.14 - 3.15 - 3.16 - 3.19 und 3.10 aufgeführt sind.   In dieser Norm wird das Anheben von Personen mit Hilfe von Anbaugeräten, wie z. B. Arbeitsbühnen, nicht behandelt.   Sie gilt nicht für Flurförderzeuge, die mit Tragmitteln veränderlicher Länge ausgerüstet sind (wie Ketten oder Seile) und ein freies Pendeln der Last in alle Richtungen ermöglichen.

Sécurité des chariots de manutention - Chariots automoteurs à portée variable

La présente norme s'applique aux chariots de manutention automoteurs à conducteur porté à portée variable destinés à manutentionner des charges de toute nature à l'aide d'un des équipements tels que énumérés, par exemple en 3.10 - 3.11 - 3.13 - 3.14 - 3.15 - 3.16 - 3.19 3.20. Elle ne traite pas du levage des personnes au moyen d'un quelconque équipement, notamment une plate-forme de travail.  Elle ne s'applique pas aux chariots comportant des éléments de suspension de la charge à longueur variable (tels que chaînes, câbles) et permettant à la charge d'osciller librement en toutes directions.

Varnost vozil za talni transport - Samognana vozila z mehanizmom za dviganje s spremenljivim dosegom

General Information

Status
Withdrawn
Publication Date
15-Dec-1998
Withdrawal Date
12-Jan-2010
ICS
53.060 - Industrial trucks
Technical Committee
CEN/TC 150 - Industrial trucks - Safety
Drafting Committee
CEN/TC 150/WG 2 - Variable reach trucks
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
13-Jan-2010
Completion Date
13-Jan-2010
Directive
98/37/EC - Machinery
Mandate
M/BC/CEN/91/1 - Standardization request to CEN/CENELEC concerning machines presenting hazards due to mobility or load lifting
Ref Project
SIST EN 1459:1999 - Safety of industrial trucks - Self-propelled variable reach trucks

Relations

Merged Into
EN 1459:1998+A2:2010 - Safety of industrial trucks - Self-propelled variable reach trucks
Effective Date
18-Jan-2023
Revised
EN ISO 3691-5:2009 - Industrial trucks - Safety requirements and verification - Part 5: Pedestrian-propelled trucks (ISO 3691-5:2009)
Effective Date
22-Dec-2008
Corrected By
EN 1459:1998/AC:2006 - Safety of industrial trucks - Self-propelled variable reach trucks
Effective Date
08-Jun-2022
Amended By
EN 1459:1998/A1:2006 - Safety of industrial trucks - Self-propelled variable reach trucks
Effective Date
08-Jun-2022

Buy Standard

EN 1459:1999EN 1459:1999
PreviousNext
Standard
EN 1459:1999
English language
80 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1459:1999
01-junij-1999
Varnost vozil za talni transport - Samognana vozila z mehanizmom za dviganje s
spremenljivim dosegom
Safety of industrial trucks - Self-propelled variable reach trucks
Sicherheit von Flurförderzeugen - Kraftbetriebene Stapler mit veränderlicher Reichweite
Sécurité des chariots de manutention - Chariots automoteurs a portée variable
Ta slovenski standard je istoveten z: EN 1459:1998
ICS:
53.060 Industrijski tovornjaki Industrial trucks
SIST EN 1459:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 1459:1999

---------------------- Page: 2 ----------------------
SIST EN 1459:1999

---------------------- Page: 3 ----------------------
SIST EN 1459:1999

---------------------- Page: 4 ----------------------
SIST EN 1459:1999

---------------------- Page: 5 ----------------------
SIST EN 1459:1999

---------------------- Page: 6 ----------------------
SIST EN 1459:1999

---------------------- Page: 7 ----------------------
SIST EN 1459:1999

---------------------- Page: 8 ----------------------
SIST EN 1459:1999

---------------------- Page: 9 ----------------------
SIST EN 1459:1999

---------------------- Page: 10 ----------------------
SIST EN 1459:1999

---------------------- Page: 11 ----------------------
SIST EN 1459:1999

---------------------- Page: 12 ----------------------
SIST EN 1459:1999

---------------------- Page: 13 ----------------------
SIST EN 1459:1999

---------------------- Page: 14 ----------------------
SIST EN 1459:1999

---------------------- Page: 15 ----------------------
SIST EN 1459:1999

---------------------- Page: 16 ----------------------
SIST EN 1459:1999

---------------------- Page: 17 ----------------------
SIST EN 1459:1999

---------------------- Page: 18 ----------------------
SIST EN 1459:1999

---------------------- Page: 19 ----------------------
SIST EN 1459:1999

---------------------- Page: 20 ----------------------
SIST EN 1459:1999

---------------------- Page: 21 ----------------------
SIST EN 1459:1999

---------------------- Page: 22 ----------------------
SIST EN 1459:1999

---------------------- Page: 23 ----------------------
SIST EN 1459:1999

---------------------- Page: 24 ----------------------
SIST EN 1459:1999

---------------------- Page: 25 ----------------------
SIST EN 1459:1999

---------------------- Page: 26 ----------------------
SIST EN 1459:1999

---------------------- Page: 27 ----------------------
SIST EN 1459:1999

---------------------- Page: 28 ----------------------
SIST EN 1459:1999

---------------------- Page: 29 ----------------------
SIST EN 1459:1999

---------------------- Page: 30 ----------------------
SIST EN 1459:1999

---------------------- Page: 31 ----------------------
SIST EN 1459:1999

---------------------- Page: 32 ----------------------
SIST EN 1459:1999

---------------------- Page: 33 ----------------------
SIST EN 1459:1999

---------------------- Page: 34 ----------------------
SIST EN 1459:1999

---------------------- Page: 35 ----------------------
SIST EN 1459:1999

---------------------- Page: 36 ----------------------
SIST EN 1459:1999

---------------------- Page: 37 ----------------------
SIST EN 14
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16307-2:2023(Main)
Industrial trucks - Safety requirements and verification - Part 2: Supplementary requirements for self-propelled variable-reach trucks
SIST EN 16307-2:2023

This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-2:2023.
This document is intended to be used in conjunction with EN ISO 3691 2:2023. These requirements are supplementary to those stated in EN ISO 3691-2:2023.
This document deals with the following supplementary requirements and significant hazards, hazardous situations or hazardous events relevant, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
-   electrical requirements;
-   noise emissions;
-   vibration;
-   electromagnetic radiation.
This document specifies supplementary requirements to EN ISO 3691-2:2023:
-   operator's seat;
-   protection against crushing, shearing and trapping;
-   longitudinal stability determination;
-   visibility;
-   information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16307-3:2023(Main)
Industrial trucks - Safety requirements and verification - Part 3: Supplementary requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads (additional requirements to EN 16307-1)
SIST EN 16307-3

This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-3:2016.
This document is intended to be used in conjunction with EN ISO 3691-3:2016. These requirements are supplementary to those stated in EN ISO 3691-3:2016.
This document deals with the following significant hazards, hazardous situations or hazardous events relevant when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
-   acceleration, deceleration (kinetic energy);
-   machinery mobility.
This document specifies supplementary requirements to EN ISO 3691-1:2015, EN ISO 3691-3:2016 and EN 16307-1:2020:
-   brakes operation without guidance system;
-   operator fall protection;
-   information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3691-3:2016/A1:2023(Amendment)
Industrial trucks - Safety requirements and verification - Part 3: Additional requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads - Amendment 1 (ISO 3691 3:2016/Amd 1:2023)
SIST EN ISO 3691-3:2017/A1:2023

2021-07-26 JF: Through decision 429/2021 taken on 2021-07-08, TC decided to decouple the WI from the EU legislation

  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3691-2:2023(Main)
Industrial trucks - Safety requirements and verification - Part 2: Self-propelled variable-reach trucks (ISO 3691-2:2023)
SIST EN ISO 3691-2:2023

This document gives safety requirements and the means for their verification for self-propelled industrial variable-reach trucks and variable-reach container handlers/reach stackers as defined in ISO 5053‑1 (hereafter referred to as trucks), equipped with forks or integral load-handling devices for normal industrial duties (e.g. fork arms or means, such as spreaders, for handling containers).
This document does not apply to:
—    rough-terrain variable-reach trucks,
—    rough-terrain variable-reach trucks for handling containers,
—    lorry mounted trucks covered by ISO 20297-1,
—    machines designed primarily for earth-moving (e.g. loaders and dozers), even when their buckets and blades are replaced with forks,
—    machines from which the load can swing freely in all directions.
This document is not applicable to trucks manufactured before the date of its publication.
For the purposes of this document, fork arms and integrated attachments are considered to be a part of the truck, whereas attachments/equipment/tools mounted on the load carrier or on the fork arms which are removable by the user are not. Nevertheless, for interchangeable equipment, which is assembled with the truck by the operator in order to change the function of, or attribute a new function to, the truck, this document does provide requirements for:
—    the interface with the truck,
—    protection of the operator in the normal operating position from crushing and shearing hazards,
—    operating and maintenance instructions,
—    load charts,
—    marking,
—    provision for transportation, and,
—    indicator lights for attachments for lifting containers
Any regional requirements additional to the provisions of this document are addressed in EN 16307-2:2023 and ISO/TS 3691‑8.
This document deals with all significant hazards, hazardous situations or hazardous events, as listed in Annex B, with the exception of the following, relevant to the applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It does not establish requirements for hazards that can occur:
—    during construction;
—    when using trucks on public roads;
—    when operating in potentially explosive atmospheres;
—    when lifting persons; or
—    during dismantling, disabling and scrapping.
This document does not provide requirements for:
—    tools, lifting accessories or removeable attachments, which do not change the function or attribute a new function, mounted on the load carrier or fork arms;
—    attachments/equipment mounted on the load carrier or on the fork arms which are removable by the user and which change the function or attribute a new function, except as stated above;
—    the reliability of control systems and performance requirements for safety related parts of control systems; or
—    the requirement for fitting an enclosed cab, whether pressurized or not.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1757:2022(Main)
Safety of industrial trucks - Pedestrian propelled industrial platform trucks
SIST EN 1757:2022

This document applies to pedestrian propelled industrial platform trucks as defined in 3.1 with a rated capacity up to and including 500 kg, hereinafter referred to as “trucks” and designed for general purposes.
This document does not apply to:
—   shopping trolleys referred to in EN 1929, Parts 1 to 4 and 7 (CEN/TC 291);
—   roll containers referred to in EN 12674, Parts 1 to 4 (CEN/TC 261);
—   trucks that are intended to be towed by powered vehicles, e.g. milk-run-trains/trailer trains/tugger trains.
This document deals with the technical requirements to minimize the hazards listed in Annex C which can arise during commissioning, operation and maintenance of trucks when carried out in accordance with the specifications as intended by the manufacturer.
This document does not specify the additional requirements for:
—   operation in severe conditions (e.g. extreme environmental conditions such as: freezer applications, high temperatures, corrosive environment);
—   operation subject to special rules (e.g. potentially explosive atmospheres);
—   handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/alkalis, radiating materials, especially brittle loads);
—   hazards occurring during construction, transportation, decommissioning and disposal;
—   direct contact with foodstuffs;
—   operation on gradients or on surfaces other than smooth, level, hard surfaces;
—   trucks designed for special applications (e.g., trucks used in hospitals as dinner trollies);
—   trucks fitted with hinged or sliding doors.
Other possible limitations of the scope of other standards referred to that also apply to this document.
Hazards relating to noise, vibration, visibility and static electricity are not dealt with in this document.
This document applies to trucks manufactured after the date of issue.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3691-6:2021(Main)
Industrial trucks - Safety requirements and verification - Part 6: Burden and personnel carriers (ISO 3691-6:2021)
SIST EN ISO 3691-6:2022

This document gives safety requirements and the means for their verification for self-propelled carriers designed for carrying burdens without lifting, as defined in ISO 5053‑1:2020, and/or personnel carriers, having three or more wheels, a maximum speed not exceeding 56 km/h and a load capacity not exceeding 5 000 kg (hereafter referred to as carriers or trucks).
This document is applicable to trucks equipped with a platform (which can be tilting) for the purpose of carrying materials or with a number of seats for the purpose of transporting passengers.
It is not applicable to:
—    vehicles intended primarily for earth-moving or over-the-road hauling;
—    driverless trucks;
—    pedestrian controlled trucks;
—    golf cars;
—    tractors with a drawbar pull up to and including 20 000 N equipped with a platform for the purpose of carrying materials.
This document deals with all significant hazards, hazardous situations or hazardous events, as listed in Annex A, relevant to the applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not deal with hazard due to the risk of break-up during operation.
It does not establish requirements for hazards that can occur when using trucks on public roads or when operating in potentially explosive atmospheres.
It does not establish requirements to provide fire extinguishers.
Regional requirements, additional to the requirements given in this document, are addressed in EN 16307‑6:2014 and ISO/TS 3691‑8:2019.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18063-2:2021(Main)
Rough-terrain trucks - Visibility test methods and their verification - Part 2: Slewing rough-terrain variable-reach trucks (ISO 18063-2:2021)
SIST EN ISO 18063-2:2021

This document applies to slewing rough-terrain variable-reach trucks (hereinafter referred to as trucks) as defined in ISO 5053-1:2020, 3.22, that have a specific seated operator’s position, on the left-hand side of the boom, or centre position (excluding operator position on the right side of the boom).
This document specifies a static test method for determining and evaluating the operator’s visibility on a rectangular boundary close around the truck and on a 12 m visibility test circle. Performance requirements for visibility are specified in this document. A calculation method or computer simulation can also be used.
This document does not provide performance requirements for the additional means for indirect visibility.
This document also covers information to be provided by the manufacturer.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1459-9:2021(Main)
Rough-terrain trucks - Safety requirements and verification - Part 9: Variable-reach trucks equipped with work platforms having a front guard that can be opened
SIST EN 1459-9:2021

This document specifies the safety requirements for slewing rough-terrain variable-reach trucks and rough-terrain variable-reach trucks defined by ISO 5053-1 (hereafter referred to as trucks) and their work platforms having front guards that can be opened for removal of roof material (hereafter referred to as work platforms).
This document deals with the significant hazards, hazardous situations and events relevant to the combination of the truck and the integrated work platform when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. The significant hazards covered by this document are listed in Annex A.
NOTE 1 Duplicate controls for the slewing upper structure, the boom and the work platform movements can be also provided under specific circumstances at the operating position in the enclosed cab of the truck.
This document does not address hazards which can occur:
a) when using non-integrated work platforms or other attachments not designed for lifting persons;
b) when handling suspended work platforms which can swing freely;
c) when operating underground or in potentially explosive atmospheres;
d) when removing asbestos, regarding the possible release of fibres.
This document does not specify safety requirements for trucks equipped with work platforms intended for leaving and re-entering at height.
NOTE 2 National regulations for worksites can apply for asbestos removal to cover the risks related to the possible release of fibres.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16842-5:2021(Main)
Powered industrial trucks - Visibility - Test methods and verification - Part 5: Industrial variable-reach trucks greater than 10 000 kg capacity
SIST EN 16842-5:2021

This document specifies the requirements and test procedures for 360° visibility of sit on self-propelled industrial variable-reach trucks (herein after referred to as trucks) without a load, with a capacity greater than 10 000 kg in accordance with ISO 5053-1. It is intended be used in conjunction with EN 16842 1.
Where specific requirements in this part are modified from the general requirements in EN 16842-1, the requirements of this part are truck specific and to be used for sit-on self-propelled industrial variable-reach trucks with a capacity greater than 10 000 kg.
This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events, relevant to the visibility of the operator for applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not deal with rough-terrain variable-reach trucks (see EN 15830).

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16842-8:2021(Main)
Powered industrial trucks - Visibility-Test methods and verification - Part 8: Stand-on counterbalance trucks up to and including 10 000 kg capacity
SIST EN 16842-8:2021

This document specifies the requirements and test procedures for 360° visibility of stand-on counterbalance trucks with a capacity up to and including 10 000 kg in accordance with ISO 5053-1 (herein after referred to as trucks) without a load and it is intended to be used in conjunction with EN 16842-1.
Where specific requirements in this part are modified from the general requirements in EN 16842-1, the requirements of this part are truck-specific and to be used for stand-on counterbalance trucks with a capacity up to and including 10 000 kg.
This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events, relevant to the visibility of the operator for applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day