EN ISO 2702:2011
(Main)Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
ISO 2702:2011 specifies the characteristics of heat-treated steel tapping screws, with tapping screw thread from ST2,2 to ST9,5 inclusive according to ISO 1478, together with the corresponding test methods.
Wärmebehandelte Blechschrauben aus Stahl - Mechanische Eigenschaften (ISO 2702:2011)
Die vorliegende Internationale Norm legt die Eigenschaften von wärmebehandelten Blechschrauben mit
einem Blechschrauben-Gewinde von ST2,2 bis einschließlich ST9,5 nach ISO 1478 zusammen mit den
zugehörigen Prüfverfahren fest.
Vis à tôle en acier traité thermiquement - Caractéristiques mécaniques (ISO 2702:2011)
L'ISO 2702:2011 spécifie les caractéristiques mécaniques des vis à tôle en acier traitées thermiquement, de filetage ST2,2 à ST9,5 inclus conforme à l'ISO 1478, ainsi que les méthodes d'essai correspondantes.
Toplotno obdelani pločevinski vijaki - Mehanske lastnosti (ISO 2702:2011)
Ta mednarodni standard določa značilnosti toplotno obdelanih pločevinastih vijakov z navojem vijaka od ST 2,2 do vključno ST 9,5 v skladu z ISO 1478, skupaj s pripadajočimi preskusnimi metodami.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 2702:2011
01-oktober-2011
1DGRPHãþD
SIST EN ISO 2702:1996
7RSORWQRREGHODQLSORþHYLQVNLYLMDNL0HKDQVNHODVWQRVWL ,62
Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
Wärmebehandelte Blechschrauben aus Stahl - Mechanische Eigenschaften (ISO
2702:2011)
Vis à tôle en acier traité thermiquement - Caractéristiques mécaniques (ISO 2702:2011)
Ta slovenski standard je istoveten z: EN ISO 2702:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 2702:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 2702:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 2702:2011
EUROPEAN STANDARD
EN ISO 2702
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2011
ICS 21.060.10 Supersedes EN ISO 2702:1994
English Version
Heat-treated steel tapping screws - Mechanical properties (ISO
2702:2011)
Vis à tôle en acier traité thermiquement - Caractéristiques Wärmebehandelte Blechschrauben aus Stahl -
mécaniques (ISO 2702:2011) Mechanische Eigenschaften (ISO 2702:2011)
This European Standard was approved by CEN on 28 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2702:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 2702:2011
EN ISO 2702:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 2702:2011
EN ISO 2702:2011 (E)
Foreword
This document (EN ISO 2702:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2011, and conflicting national standards shall be withdrawn
at the latest by November 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2702:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2702:2011 has been approved by CEN as a EN ISO 2702:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 2702:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 2702:2011
INTERNATIONAL ISO
STANDARD 2702
Third edition
2011-05-01
Heat-treated steel tapping screws —
Mechanical properties
Vis à tôle en acier traité thermiquement — Caractéristiques mécaniques
Reference number
ISO 2702:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 2702:2011
ISO 2702:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.