EN 4695:2017
(Main)Aerospace series - Tie Rod with integrated bolts - Assembly Code G, H and K
Aerospace series - Tie Rod with integrated bolts - Assembly Code G, H and K
This standard specifies the dimensions and tolerances of rod assemblies for aerospace applications with two adjustable ends with integrated bolts for interior and sub structure in the temperature range − 55 °C to 85 °C. The rod ends should not be screwed completely apart.
Luft- und Raumfahrt - Zug-Druck-Stange mit integrierten Bolzen - Variante G, H und K
Série aérospatiale - Bielle avec axes intégrés - Code assemblage G, H et K
Aeronavtika - Zglobna ročica z vgrajenim sornikom - Montažne kode G, H in K
Ta standard določa mere in tolerance sestavov ročic z dvema nastavljivima končnikoma z vgrajenimi sorniki za uporabo v aeronavtiki v notranjosti ali podstrukturah v temperaturnem razponu od –55 °C do 85 °C. Končnika ročice ne smeta biti privita tako, da sta povsem narazen.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Zug-Druck Stange mit integrierten Bolzen - Zusammenbaucode G, H und KSérie aérospatiale - Bielle avec axes intégrés - Code assemblage G, H et KAerospace series - Tie Rod with integrated bolts - Assembly Code G, H and K49.035Sestavni deli za letalsko in vesoljsko gradnjoComponents for aerospace constructionICS:Ta slovenski standard je istoveten z:EN 4695:2017SIST EN 4695:2017en,fr,de01-december-2017SIST EN 4695:2017SLOVENSKI
STANDARD
SIST EN 4695:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4695
October
t r s y ICS
v {ä r u w English Version
Aerospace series æ Tie Rod with integrated bolts æ Assembly Code Gá H and K Série aérospatiale æ Bielle avec axes intégrés æ Code assemblage Gá H et K
Luftæ und Raumfahrt æ ZugæDruck Stange mit integrierten Bolzen æ Variante Gá H und K This European Standard was approved by CEN on
t w June
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v x { wã t r s y ESIST EN 4695:2017
EN 4695:2017 (E) 2 Contents Page European foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5 3 Requirements . 6 4 Assembly code definitions . 6 5 Materials . 8 6 Locking clips . 8 7 Fork and eye ends . 10 8 Mass calculation of tie rods . 16 9 Marking . 17 10 Dimensions . 18 11 Designation. 18 12 Technical specification . 18 Annex A (informative)
Standard evolution form . 19
SIST EN 4695:2017
EN 4695:2017 (E) 3 European foreword This document (EN 4695:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this St
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.