EN ISO 12216/prA1
(Amendment)Small craft - Windows, portlights, hatches, deadlights and doors - Strength and watertightness requirements (ISO 12216:2020)
Small craft - Windows, portlights, hatches, deadlights and doors - Strength and watertightness requirements (ISO 12216:2020)
2021-11-12 (DATA): Amendment created following CEN/BT C214/2021 for the assesment to be requested. The adoption of the main should be published together with this amendment (WI 00464087).
Kleine Wasserfahrzeuge - Fenster, Bullaugen, Luken, Seeschlagblenden und Türen - Anforderungen an die Festigkeit und Wasserdichtheit (ISO 12216:2020)
No scope available
Petits navires - Fenêtres, hublots, panneaux, tapes et portes - Exigences de résistance et d'étanchéité (ISO 12216:2020)
Mala plovila - Okna, lopute, pokrovi in vrata - Zahteve za trdnost in odpornost proti vodi - Dopolnilo A1 (ISO 12216:2020/DAM 1:2022)
General Information
RELATIONS
Standards Content (sample)
SLOVENSKI STANDARD
oSIST prEN ISO 12216:2022/oprA1:2022
01-april-2022
Mala plovila - Okna, lopute, pokrovi in vrata - Zahteve za trdnost in odpornost proti
vodi - Dopolnilo A1 (ISO 12216:2020/DAM 1:2022)Small craft - Windows, portlights, hatches, deadlights and doors - Strength and
watertightness requirements - Amendment 1 (ISO 12216:2020/DAM 1:2022)
Petits navires - Fenêtres, hublots, panneaux, tapes et portes - Exigences de résistance
et d'étanchéité - Amendement 1 (ISO 12216:2020/DAM 1:2022)Ta slovenski standard je istoveten z: EN ISO 12216/prA1
ICS:
47.080 Čolni Small craft
91.060.50 Vrata in okna Doors and windows
oSIST prEN ISO 12216:2022/oprA1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------oSIST prEN ISO 12216:2022/oprA1:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 12216:2022/oprA1:2022
DRAFT AMENDMENT
ISO 12216:2020/DAM 1
ISO/TC 188 Secretariat: SIS
Voting begins on: Voting terminates on:
2022-01-28 2022-04-22
Small craft — Windows, portlights, hatches, deadlights and
doors — Strength and watertightness requirements
AMENDMENT 1
Petits navires — Fenêtres, hublots, panneaux, tapes et portes — Exigences de résistance et d'étanchéité
AMENDEMENT 1ICS: 47.080
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 12216:2020/DAM 1:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 12216:2022/oprA1:2022
ISO 12216:2020/DAM 1:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 12216:2022/oprA1:2022
ISO 12216:2020/DAM 1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.ISO 12216:2020 was prepared by Technical Committee ISO/TC 188, Small craft.
This amendment 1 to ISO 12216:2020 was prepared by ISO/TC 188, Small craft.
The main changes compared to the previous edition are as follows:
— ISO 11812:2020 Small craft — Watertight cockpits and quick-draining cockpits has been deleted in
Clause 2;...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.