EN 6101:2022
(Main)Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series
Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series
This document specifies the dimensions, tolerances and mass of rivets with 100° medium flush head, close tolerance, inch series, for aerospace application.
Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Inch-Reihe
Dieses Dokument legt die Maße, Grenzabmaße und Masse von Vollnieten mit 100° Medium Senkkopf, enge Toleranz, Zoll Reihe, für die Anwendung in der Luft und Raumfahrt fest.
Série aérospatiale - Rivets de précision, tête fraisée moyenne 100° - Série en inches
Le présent document spécifie les dimensions, les tolérances et la masse des rivets de précision à tête fraisée moyenne 100°, série en inches, pour les applications aérospatiales.
Aeronavtika - Kovice, 100° srednje ugrezna glava, ozka toleranca - Palčne mere
Ta dokument določa dimenzije, tolerance in maso zakovic s 100° srednje ugrezno glavo, ozka toleranca, colska izvedba za uporabo v aeronavtiki.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 6101:2023
01-marec-2023
Nadomešča:
SIST EN 6101:2016
Aeronavtika - Kovice, 100° srednje ugrezna glava, ozka toleranca - Palčne mere
Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series
Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Inch-Reihe
Série aérospatiale - Rivets de précision, tête fraisée moyenne 100° - Série en inches
Ta slovenski standard je istoveten z: EN 6101:2022
ICS:
21.060.40 Kovice Rivets
49.030.60 Kovice Rivets
SIST EN 6101:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 6101:2023
---------------------- Page: 2 ----------------------
SIST EN 6101:2023
EN 6101
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 49.030.60 Supersedes EN 6101:2016
English Version
Aerospace series - Rivet, 100° medium flush head, close
tolerance - Inch series
Série aérospatiale - Rivets de précision, tête fraisée Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf,
moyenne 100° - Série en inches enge Toleranz - Inch-Reihe
This European Standard was approved by CEN on 30 May 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6101:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 6101:2023
EN 6101:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Requirements . 6
4.1 Configuration, dimensions, tolerances and masses . 6
4.2 Material and surface treatment . 8
5 Designation . 11
6 Marking . 12
6.1 Material identification . 12
6.2 Manufacturer’s identification . 12
6.3 Identification of oversize rivets . 12
7 Technical specification .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.