iTeh Standards logo
EURUSD
Your shopping cart is empty.
CEN

EN 1253-3:2016

(Main)

Gullies for buildings - Part 3: Evaluation of conformity

Gullies for buildings - Part 3: Evaluation of conformity

This draft European Standard specifies the requirements for evaluation of conformity for floor gullies, roof drains and access covers for buildings to ensure conformity of these products with EN 1253-1, EN 1253-2 and FprEN 1253-4.

Abläufe für Gebäude - Teil 3: Bewertung der Konformität

Diese Europäische Norm legt die Anforderungen an die Bewertung der Konformität für Bodenabläufe, Dach-abläufe und Abdeckungen für Gebäude fest, um die Konformität dieser Produkte mit EN 1253-1, EN 1253-2 und EN 1253-4 sicherzustellen.

Avaloirs et siphons pour bâtiments - Partie 3: Évaluation de la conformité

La présente Norme européenne spécifie les exigences pour l'évaluation de la conformité des avaloirs/siphons de sol, des avaloirs de toiture et des tampons/couvercles d'accès utilisés dans des bâtiments, afin de garantir la conformité de ces produits avec les normes EN 1253-1, EN 1253-2 et EN 1253-4.

Odtoki v stavbah - 3. del: Vrednotenje skladnosti

Ta osnutek evropskega standarda določa zahteve za vrednotenje skladnosti za talne odtoke, žlebove in pokrove za stavbe, da se zagotovi skladnost teh izdelkov s standardi EN 1253-1, EN 1253-2 in FprEN 1253-4.

General Information

Status
Published
Publication Date
17-May-2016
ICS
91.140.80 - Drainage systems
Technical Committee
CEN/TC 165 - Waste water engineering
Drafting Committee
CEN/TC 165/WG 11 - Waste fittings
Current Stage
9093 - Decision to confirm - Review Enquiry
Start Date
09-Jun-2022
Completion Date
14-Apr-2025
Ref Project
SIST EN 1253-3:2016 - Gullies for buildings - Part 3: Evaluation of conformity

Relations

Replaces
EN 1253-3:1999 - Gullies for buildings - Part 3: Quality control
Effective Date
25-May-2016

EN 1253-3:2016 – Gullies for Buildings: Evaluation of Conformity

Overview

EN 1253-3:2016 is a European Standard developed by CEN that addresses the evaluation of conformity for building drainage components - specifically floor gullies, roof drains, and access covers. This standard ensures that these products comply with the technical and performance requirements set out in EN 1253-1, EN 1253-2, and EN 1253-4. By establishing rigorous conformity evaluation criteria, the standard promotes quality assurance and reliability in drainage and sewage systems within buildings.

This part of the EN 1253 series focuses on the processes and control measures that manufacturers must follow to demonstrate consistent product conformity, including type testing, factory production control, and third-party verification. EN 1253-3:2016 supersedes the previous 1999 edition, incorporating updated control practices aligned with modern manufacturing and inspection techniques.

Key Topics

  • Scope of Evaluation
    The standard specifies requirements for conformity evaluation of:

    • Trapped floor gullies with water seal depth ≥ 50 mm (EN 1253-1)
    • Roof drains and gullies without traps (EN 1253-2)
    • Access covers for gullies (EN 1253-4)

  • Evaluation Procedures
    Two main procedures form the basis of conformity evaluation:

    • Type Testing: Testing three production specimens against relevant standards to verify design and material compliance.
    • Factory Production Control (FPC): Ongoing internal monitoring of production to ensure continued conformity during manufacturing, covering appearance, dimensions, materials, and strength classifications.

  • Factory Production Control Requirements
    Manufacturers must implement robust FPC systems, including:

    • Skilled staff and independence in quality control
    • Adequate testing and measuring equipment
    • Documented quality plans outlining inspection methods, frequency, and documentation
    • Written procedures for document control, handling of non-conforming products, complaints management, and calibration of equipment

  • Third Party Control (Recommended)
    Independent third party inspection enhances reliability through:

    • Approval of type testing and production evaluation
    • On-site inspections twice a year to verify factory control effectiveness
    • Independent product testing covering key characteristics
    • Formal reporting and retesting procedures in case of product non-conformity

  • Documentation and Reporting
    Detailed records of production steps, testing results, inspection frequency, and corrective actions must be maintained and made available for third party audits.

Applications

  • Building Drainage Systems
    EN 1253-3:2016 is applicable to manufacturers and suppliers of floor gullies, roof drains, and access covers used in residential, commercial, and industrial buildings. Ensuring conformity with this standard guarantees:

    • Effective drainage performance
    • Long-term durability and safety
    • Compliance with European building regulations and national standards

  • Quality Assurance in Manufacturing
    Construction product manufacturers use this standard to develop and maintain factory quality control systems that meet European market requirements.

  • Certification and Market Access
    Products evaluated in accordance with EN 1253-3:2016 benefit from easier acceptance across CEN member countries, facilitating trade and market entry within Europe.

Related Standards

  • EN 1253-1:2015 - Gullies for buildings - Part 1: Trapped floor gullies with water seal depth of at least 50 mm
  • EN 1253-2:2015 - Gullies for buildings - Part 2: Roof drains and floor gullies without trap
  • EN 1253-4:2016 - Gullies for buildings - Part 4: Access covers
  • EN ISO 9001 - Quality management systems - Requirements, for structuring factory production control and quality assurance processes

Keywords: EN 1253-3:2016, gullies for buildings, evaluation of conformity, floor gullies, roof drains, access covers, drainage system standards, factory production control, type testing, third party certification, European standards, building drainage compliance.

EN 1253-3:2016EN 1253-3:2016
PreviousNext
Standard
EN 1253-3:2016
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Frequently Asked Questions

EN 1253-3:2016 is a standard published by the European Committee for Standardization (CEN). Its full title is "Gullies for buildings - Part 3: Evaluation of conformity". This standard covers: This draft European Standard specifies the requirements for evaluation of conformity for floor gullies, roof drains and access covers for buildings to ensure conformity of these products with EN 1253-1, EN 1253-2 and FprEN 1253-4.

This draft European Standard specifies the requirements for evaluation of conformity for floor gullies, roof drains and access covers for buildings to ensure conformity of these products with EN 1253-1, EN 1253-2 and FprEN 1253-4.

EN 1253-3:2016 is classified under the following ICS (International Classification for Standards) categories: 91.140.80 - Drainage systems. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 1253-3:2016 has the following relationships with other standards: It is inter standard links to EN 1253-3:1999. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

You can purchase EN 1253-3:2016 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Odtoki v stavbah - 3. del: Vrednotenje skladnostiAbläufe für Gebäude - Teil 3: Bewertung der KonformitätAvaloirs et siphons pour bâtiments - Partie 3 : Évaluation de la conformitéGullies for buildings - Part 3: Evaluation of conformity91.140.80Drenažni sistemiDrainage systemsICS:Ta slovenski standard je istoveten z:EN 1253-3:2016SIST EN 1253-3:2016en,fr,de01-julij-2016SIST EN 1253-3:2016SLOVENSKI
STANDARDSIST EN 1253-3:20001DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1253-3
May
t r s x ICS
{ sä s v rä z r Supersedes EN
s t w uæ uã s { { {English Version
Gullies for buildings æ Part
uã Evaluation of conformity Avaloirs et siphons pour bâtiments æ Partie
uã Évaluation de la conformité
Abläufe für Gebäude æ Teil
uã Bewertung der Konformität This European Standard was approved by CEN on
s v February
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t w uæ uã t r s x ESIST EN 1253-3:2016

Control by third party (third party control) . 8 A.1 General . 8 A.2 Procedure of the third party control . 8 A.3 Report by the third party . 9 A.4 Retesting . 10 A.5 Non-conforming products . 10 Bibliography . 11
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

제목: EN 1253-3:2016 - 건물용 구리 - 파트 3: 따름새 평가 내용: 이 유럽 표준 초안은 건축물용 바닥 구리, 지붕 배수구 및 진입구를 위한 따름새 평가에 대한 요구 사항을 명시한다. 이 제품들이 EN 1253-1, EN 1253-2 및 FprEN 1253-4의 요구 사항과 일치하는지 확인하기 위한 것이다.

The article discusses EN 1253-3:2016, which is a draft European Standard that focuses on evaluating the conformity of floor gullies, roof drains, and access covers for buildings. The purpose of this standard is to ensure that these products meet the requirements set forth in EN 1253-1, EN 1253-2, and FprEN 1253-4.

記事タイトル：EN 1253-3:2016 - 建物用ゴーリー - パート3：適合性の評価 記事の内容：このヨーロッパ標準の草案では、建物用のフロアゴリー、屋根の排水口、およびアクセスカバーの適合性の評価要件について規定しています。これらの製品がEN 1253-1、EN 1253-2、およびFprEN 1253-4の要件と適合していることを確認することを目的としています。

This May Also Interest You

CEN
EN 1253-7:2022(Main)
Gullies for buildings - Part 7: Trapped floor gullies with mechanical closure
SIST EN 1253-7:2023

This document classifies floor gullies for domestic waste water for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a mechanical closure (referred to as floor gullies).
NOTE   Floor gullies with a depth of water seal less than 50 mm are not covered by EN 1253-1, EN 1253-7 and EN 1253-8.
These products are intended to be installed where both conditions below are fulfilled:
-   the building does not exceed a ground-floor and three floors above;
-   infrequent use could result in a water seal evaporating.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-8:2022(Main)
Gullies for buildings - Part 8: Trapped floor gullies with combined mechanical closure and water seal
SIST EN 1253-8:2023

This document classifies floor gullies for domestic wastewater for use inside buildings, gives guidance, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with combined mechanical closure and water seal (referred to as floor gullies).
NOTE   Floor gullies with combined mechanical closure and water seal are not covered by EN 1253-1, EN 1253-6, EN 1253-7.
These products are intended to be installed where both condition below are fulfilled:
-   the building does not exceed a ground-floor and three floors above;
-   infrequent use could result in a water seal evaporating.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-6:2022(Main)
Gullies for buildings - Part 6: Trapped floor gullies with a depth of water seal less than 50 mm
SIST EN 1253-6:2023

This document classifies floor gullies for domestic waste water for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a depth of water seal less than 50 mm (referred to as floor gullies).
NOTE   Floor gullies with a depth of water seal less than 50 mm are not covered by EN 1253 1, EN 1253 7 and EN 1253 8.
These products are intended to be installed where the three following conditions are met:
-   space limitation will not accommodate a gully with a 50 mm water seal;
-   the building does not exceed a ground-floor and three floors above;
-   at least two domestic sanitary appliances are installed in addition to the gully but with only one WC on the same branch (connection pipe) or secondary or branch ventilation is installed (see EN 12056 2:2000, 4.3.2 or 4.3.4.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-9:2022(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
SIST EN ISO 11296-9:2023

This document, in conjunction with ISO 11296‑1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout.
This document is applicable to plastics inner layers and grout systems with or without steel reinforcement. It does not apply to the structural design of the lining system.
NOTE      Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-5:2017(Main)
Gullies for buildings - Part 5: Gullies with light liquids closure
SIST EN 1253-5:2017

This draft European Standard specifies requirements for the design, construction, performance, application and marking as well as test methods of factory made gullies with a light liquid closure for buildings.
Light liquid closures for buildings shall be applied to avoid uncontrolled discharge of light liquids into drainage systems in case of emergency.
This draft European Standard does not apply to installations for separation of light liquids covered by EN 858-1.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-4:2016(Main)
Gullies for buildings - Part 4: Access covers
SIST EN 1253-4:2016

This draft European Standard classifies access covers according to their loading strength and specifies requirements relating to their design, construction, marking, testing and evaluation of conformity.
This draft European Standard classifies and specifies requirements for factory made access covers used for drainage systems inside buildings. This draft standard does not apply to access covers intended for external use which are covered by EN 124 series.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12050-4:2015(Main)
Wastewater lifting plants for buildings and sites - Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter
SIST EN 12050-4:2015

This European Standard applies to non-return valves used for faecal-free wastewater and wastewater containing faecal matter lifting plants. This Standard specifies general requirements, basic construction and testing principles together with information on materials and the relevant assessment and verification of constancy of performance.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12050-1:2015(Main)
Wastewater lifting plants for buildings and sites - Part 1: Lifting plants for wastewater containing faecal matter
SIST EN 12050-1:2015

This European Standard applies to lifting plants for wastewater containing faecal matter (referred to as “faecal lifting plants” in this standard) for drainage of locations below flood level in buildings and sites to prevent any backflow of wastewater into the building. These lifting plants may be prefabricated or delivered as prefabricated kits and assembled on site. This standard specifies general requirements, basic construction and testing principles, together with information on materials and assessment and verification of constancy of performance.
Construction and testing requirements for non-return valves used in wastewater lifting plants are given in EN 12050 4.
This European Standard does not apply for pumping installations for drain and sewer systems outside buildings for pumping of municipal wastewater according to EN 752:2008, Annex F.
NOTE    Lifting plants for wastewater containing faecal matter can also be used for wastewater that does not contain faecal matter and for surface water.
This European Standard applies also to lifting plants for wastewater containing faecal matter which are not prefabricated but composed of individual components purchased from different suppliers and put together on site.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12050-3:2015(Main)
Wastewater lifting plants for buildings and sites - Part 3: Lifting plants for limited applications
SIST EN 12050-3:2015

This European Standard applies to lifting plants for limited applications for domestic non-commercial wastewater containing or not containing faecal matter and located below flood level.
NOTE   Limited application means that the number of users is small and the plant is located in the same room as the sanitary appliance(s) served by it ) which are installed in accordance with EN 12056–1 and the layout and calculation are in accordance with EN 12056–4.
This European Standard applies to lifting plants for limited applications designed for wastewater containing faecal matter, where there is another WC available above flood level, and the plants serve no more than a single WC to which it is directly connected (at a distance of max. 0,5 m) and one hand washbasin, one shower and one bidet provided no other sanitary appliance is directly or indirectly connected.
This European Standard also applies to lifting plants for limited applications designed for faecal free wastewater, where a maximum of one hand washbasin or kitchen sink plus one further appliance such as a bathtub or a washing machine or a shower or a dish washer or an urinal are connected. No other sanitary appliance shall be directly or indirectly connected.
This European Standard contains general requirements, basic construction and testing principles, together with information on materials.
Construction and testing requirements for non-return valves used in wastewater lifting plants for limited applications are given in EN 12050 4.
This European Standard does not apply for lifting plants for limited applications for wastewater containing faecal matter where WC flushing is carried out by pressure flush valve.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12050-2:2015(Main)
Wastewater lifting plants for buildings and sites - Part 2: Lifting plants for faecal-free wastewater
SIST EN 12050-2:2015

This European Standard applies to lifting plants for faecal-free wastewater for drainage of locations below flood level in buildings and sites to prevent any backflow of wastewater into the building. These lifting plants may be prefabricated or delivered as prefabricated kits and assembled on site. This standard specifies general requirements, basic construction and testing principles, together with information on materials and assessment and verification of constancy of performance.
Construction and testing requirements for non-return valves used in wastewater lifting plants are given in EN 12050 4.
This European Standard does not apply for pumping installations for drain and sewer systems outside buildings for pumping of municipal wastewater according to EN 752:2008, Annex F.
This European Standard applies also to lifting plants for faecal-free wastewater which are not prefabricated but composed of individual components purchased from different suppliers and put together on site.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day