iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1020:1997

(Main)

Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, incorporating a fan to assist transportation of combustion air and/or combustion products

Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, incorporating a fan to assist transportation of combustion air and/or combustion products

This European Standard specifies the requirements and test methods for the safety and efficiency of non-domestic gas-fired air heaters having a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances".  This includes appliances having forced draught burners.  This European Standard applies to Type B12, B13, B14, B22, B23, C12, C13, C32, C33, C62 and C63 appliances with a heat input not exceeding 300 kW (based on net calorific value) intended for use in other than single unit residential dwellings.  It also applies to appliances intended for outdoor installation.  Provision of the heated air may be by means of ducting or may be directly into the heated space.  For Type B22 appliances, this European Standard only applies to appliances having automatic ignition.  For Type C62 and and C63 appliances, this European Standard only applies when such appliances are intended for final installation in a similar manner to Type C3 appliances. This standard does not apply to:   ð appliances intended for use in a single unit residential dwelling;  ð appliances of the condensing type;  ð appliances with atmospheric burners without a fan to assist the transportation of combustion air and/or flue gases;  ð dual purpose air conditioning appliances (heating and cooling);  ð appliances where the air is heated by an intermediate fluid;  ð appliances fitted with manual or automatic flue dampers;  ð portable or transportable forced convection appliances;  ð appliances having multiple heating units with a single draught diverter;  ð appliances fitted with more than one flue outlet. This European Standard is applicable to appliances which are intended to be type tested.  NOTE: Requirements for appliances which are not type tested would need to be subject to further consideration.

Gasbefeuerte Warmlufterzeuger mit verstärkter Konvektion zum Beheizen von Räumen für den nicht-häuslichen Gebrauch mit einer Nennwärmebelastung nicht über 300 kW, mit Gebläse zur Beförderung der Verbrennungsluft und/oder der Abgase

Diese europäische Norm spezifiziert die Anforderungen und Prüfverfahren für die Sicherheit und den Wirkungsgrad gasbefeuerter Warmlufterzeuger für den nicht-häuslichen Gebrauch mit einem Gebläse zur Beförderung der Verbrennungsluft und/oder der Abgase, nachfolgen kurz als "Geräte" bezeichnet. Dies umfaßt Geräte mit Gebläsebrennern.

Générateurs d'air chaud à convection forcée utilisant les combustibles gazeux pour le chauffage de locaux autres que l'habitat individuel de débit calorifique inférieur ou égal à 300 kW (sur pouvoir calorifique inférieur), comportant un ventilateur pour aider l'alimentation en air comburant et/ou l'évacuation des produits de combustion

La présente norme européenne définit les exigences et les méthodes d'essai relatives à la sécurité et au rendement des générateurs d'air chaud à usage non domestique fonctionnant au gaz, comportant un ventilateur pour aider l'alimentation en air comburant et/ou l'évacuation des produits de combustion, applelés ci-après "appareils". Ceci inclut les appareils équipés de brûleurs à air soufflé.

Plinski grelniki zraka s prisilno konvekcijo, za ogrevanje nestanovanjskih prostorov, z imensko močjo do vključno 300 kW, z ventilatorjem za zgorevalni zrak in/ali produkte zgorevanja

General Information

Status
Withdrawn
Publication Date
16-Dec-1997
Withdrawal Date
03-Nov-2009
ICS
91.140.10 - Central heating systems
Technical Committee
CEN/TC 180 - Non-domestic gas-fired overhead radiant heaters
Drafting Committee
CEN/TC 180 - Non-domestic gas-fired overhead radiant heaters
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
04-Nov-2009
Completion Date
04-Nov-2009
Directive
2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
90/396/EEC - Appliances burning gaseous fuels
Mandate
M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
Ref Project
SIST EN 1020:1999 - Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, incorporating a fan to assist transportation of combustion air and/or combustion products

Relations

Amended By
EN 1020:1997/A1:2001 - Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, incorporating a fan to assist transportation of combustion air and/or combustion products
Effective Date
08-Jun-2022
Replaced By
EN 1020:2009 - Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products
Effective Date
08-Jun-2022

Buy Standard

EN 1020:1999EN 1020:1999
PreviousNext
Standard
EN 1020:1999
English language
132 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RYDQMVNLKGasbefeuerte Warmlufterzeuger mit verstärkter Konvektion zum Beheizen von Räumen für den nicht-häuslichen Gebrauch mit einer Nennwärmebelastung nicht über 300 kW, mit Gebläse zur Beförderung der Verbrennungsluft und/oder der AbgaseGénérateurs d'air chaud a convection forcée utilisant les combustibles gazeux pour le chauffage de locaux autres que l'habitat individuel de débit calorifique inférieur ou égal a 300 kW (sur pouvoir calorifique inférieur), comportant un ventilateur pour aider l'alimentation en air comburant et/ou l'évacuation des produits de combustionNon-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, incorporating a fan to assist transportation of combustion air and/or combustion products97.100.20Plinski grelnikiGas heatersICS:Ta slovenski standard je istoveten z:EN 1020:1997SIST EN 1020:1999en01-december-1999SIST EN 1020:1999SLOVENSKI
STANDARD



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN 1020:1999



SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17522:2023(Main)
Design and construction of backfilled and grouted borehole heat exchangers
SIST EN 17522:2023

This document covers standardization in the field of geological and environmental aspects, design, construction, operation, monitoring, maintenance and decommissioning of grouted borehole heat exchangers for uses in geothermal energy systems.
This document is only applicable for backfilled and grouted boreholes, it is not applicable for groundwater-filled boreholes.
Direct expansion and thermal syphon techniques are excluded from this document.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 12098-6:2022(Main)
Energy performance of buildings - Controls for heating systems - Part 6: Accompanying TR EN 12098-1:2022 - Modules M3-5,6,7,8
SIST-TP CEN/TR 12098-6:2023

This document refers to EN 12098-1:2022, Energy performance of buildings - Controls for heating systems - Part 1: Control equipment for hot water heating systems - Modules M3-5, 6, 7, 8.
It contains information to support the correct understanding, use and national adaption of EN 12098-1:2022.
This document does not contain any normative provisions.

  • Technical report
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12098-1:2022(Main)
Energy performance of buildings - Controls for heating systems - Part 1: Control equipment for hot water heating systems - Modules M3-5, 6, 7, 8
SIST EN 12098-1:2023

This document is applicable to electronic control equipment for heating systems with water as the heating medium and a supply water temperature up to 120 °C.
This control equipment controls the distribution and/or the generation of heat in relation to the outside temperature and time and other reference variables.
This document also is also applicable to controllers that contain an integrated optimum start or an optimum start-stop control function.
Safety requirements on heating systems remain unaffected by this document.
The dynamic behaviour of the valves and actuators are not covered in this document.
A multi-distribution and/or multi-generation system needs a coordinated solution to prevent undesired interaction and is not part of this document.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 12098-7:2022(Main)
Energy performance of buildings - Controls for heating systems - Part 7: Accompanying TR EN 12098-3:2022 - Modules M3-5,6,7,8
SIST-TP CEN/TR 12098-7:2023

This document refers to EN 12098-3:2022, Energy performance of buildings - Controls for heating systems - Part 3: Control equipment for electrical heating systems - Modules M3-5,6,7,8.
It contains information to support the correct understanding, use and national adaption of EN 12098-3:2022.
This document does not contain any normative provisions.

  • Technical report
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 303-5:2021+A1:2022(Main + Amendment)
Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking
SIST EN 303-5:2021+A1:2023

1.1 General
This European Standard applies to heating boilers including safety devices up to a nominal heat output of 500 kW which are designed for the burning of solid fuels only and are operated according to the instructions of the boiler manufacturer.
This European Standard deals with significant hazards, hazardous situations and events relevant to heating boilers used as intended and under the conditions foreseen by the manufacturer (see Clause 4).
The boilers may operate under natural draught or forced draught. The stoking may work manually or automatically.
The boilers may operate under room sealed conditions in case of supervised under pressure in the combustion chamber.
The boilers may operate in condensing condition.
NOTE This European Standard deals with boilers which are both within and outside of the scope of the Machinery
Directive 2006/42/EC.
This European Standard contains requirements and test methods for safety, combustion quality, operating characteristics, marking and maintenance of heating boilers and secondary emission reduction appliances and efficiency improvement appliances. It also covers all external equipment that influences the safety systems (e.g. back burning safety device, integral fuel hopper).
This European Standard covers only boilers that include burners as a unit. The standard applies to the combination of a boiler body with a solid fuel burner according to EN 15270 as a unit only when the whole unit is tested in accordance with this European Standard.
Heating boilers in accordance with this European Standard are designed for central heating installations where the heat carrier is water and the maximum allowable temperature is 110 °C, and which can operate at a maximum allowable operating pressure of 6 bars. For heating boilers with a built-in or attached water heater (storage or continuous flow heater), this European Standard only applies to those parts of the water heater which are necessarily subject to the operating conditions of the heating boiler (heating part).
This European Standard does not apply to:
heating boilers and other heating appliances which are also designed for the direct heating of the place of installation;
cooking appliances;
the design and construction of external fuel storage and transportation devices prior to the safety devices of the boiler;
room sealed applications above a nominal heat output > 70 kW or operated with positive pressure in the combustion chamber or operated under natural draught;
This European Standard specifies the necessary terminology for solid fuel heating boilers, the control and safety related requirements, the design requirements, the technical heating requirements (taking into account the environmental requirements) and testing, as well as the marking requirements.
This European Standard is not applicable to heating boilers which are tested before the date of its publication as an EN (European Standard).
1.2 Fuels
These boilers may burn either fossil fuels, biogenic fuels or other fuels such as peat, as specified for their use by the boiler manufacturer, in accordance with the requirements of this European Standard.
Solid fuels included in this European Standard are categorised as follows.
1.2.1 Biogenic fuels
Biomass in a natural state, in the form of:
Adaptation to new fuels standards and consideration of new fuels standards in preparation.
A log wood with moisture content w ≤ 25 %, according to EN 14961-5;
B1 chipped wood (wood chipped by machine, usually up to a maximum length of 15 cm) with moisture content from w 15 % to w 35 %, according to EN 14961-4;
B2 chipped wood as under B1, except with moisture content w > 35 %;
C1 compressed wood (e.g. pellets without additives, made of wood and/or bark particles; natural binding agents such as molasses, vegetable paraffins and starch are permitted), pellets according to EN 14961-2;
(...)

  • Standard
    103 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CWA 17941:2022(Main)
Guidelines for an integrated approach of building retrofitting projects based on enhanced shallow geothermal technologies
SIST-TP CWA 17941:2022

This CEN Workshop Agreement (CWA) provides orientation for the management of building retrofitting projects based on enhanced shallow geothermal technologies.
This document provides guidelines for the classification of an integrated design team and the identification of the primary roles of actors among the whole project life-cycle. This document also provides a general workflow for building retrofitting projects based on enhanced shallow geothermal technologies, to be adapted or modified considering the specificities of each project requirements, and site characteristics, and stakeholder profiles involved in the process.
This CWA is not designed to support European legislative requirements or to address issues with significant health and safety implications. CEN and CENELEC are not accountable for its technical content or any possible conflict with national standards or legislation.

  • Standardization document
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15502-2-1:2022(Main)
Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW
SIST EN 15502-2-1:2022

This document specifies the requirements and test methods, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as "boilers".
This document is intended to be used in conjunction with EN 15502-1:2021.
This document covers gas-fired central heating boilers from the types C1 up to C(11) and the types B2, B3 and B5:
NOTE 1   For further background information on appliance types see EN 1749:2020.
a)   that have a nominal heat input (on the basis of net calorific value) not exceeding 1 000 kW;
b)   that use one or more combustible gases of the three gas families at the pressures stated in EN 437:2021;
c)   where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
d)   where the maximum operating pressure in the water circuit does not exceed 6 bar;
e)   which can give rise to condensation under certain circumstances;
f)   which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler"; if no declaration is given the boiler is to be considered a "standard boiler";
g)   which are intended to be installed inside a building or in a partially protected place;
h)   which are intended to produce also hot water either by the instantaneous or storage principle as a single unit;
i)   which are designed for either sealed water systems or for open water systems;
j)   which are either modular boilers, or non-modular boilers.
k)   which are from the types C(10) that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa, and C(11) that have condensing boiler modules that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa.
NOTE 2   This document provides requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard, the risk associated with this alternative construction needs to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This document does not cover all the requirements for:
aa)   appliances above 1 000 kW;
ab)   appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex AB of EN 15502-1:2021);
ac)   appliances using flue dampers;
ad)   appliances of the types B21, B31, B51, C21, C41, C51, C61, C71, C81, C(12) and C(13);
ae)   C7 appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW;
af)   appliances incorporating flexible plastic flue liners;
ag)   C(10) boilers:
1)   without a gas-air ratio control, or
2)   which are non-condensing appliances, or
3)   which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));
ah)   C(11) boilers that have boiler modules:
1)   without a gas-air ratio control, or
2)   which are non-condensing appliances, or
3)   which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));
ai)   appliances intended to be connected to a flue having mechanical extraction;
aj)   surface temperatures of external parts particular to children and elderly people;
ak)   appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gas;
al)   appliances equipped with an adaptive combustion control function (ACCF);
am)   boilers intended to be installed in areas accessible to elderly people and children.

  • Standard
    107 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    109 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15502-1:2021/AC:2022(Corrigendum)
Gas-fired heating boilers - Part 1: General requirements and tests
SIST EN 15502-1:2022/AC:2023

This European Standard specifies the common requirements and test methods, as well as the classification, marking and energy labelling of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard is to be used in conjunction with the specific Parts 2 (Part 2-1 and following ones).
This European Standard applies to boilers of types B and C.
NOTE For further background information on appliance types see CEN/TR 1749:2014 [1].
a) that use one or more combustible gases of the three gas families at the pressures stated in EN 437;
b) where the temperature of the water is below or above 105 °C during normal operation;
c) where the maximum operating pressure in the water circuit does not exceed 6 bar;
d) which can give rise to condensation under certain circumstances;
e) which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler" or an "other boiler". If no declaration is given the boiler is to be considered both a "standard boiler" and an "other boiler";
NOTE The Ecodesign Directive defines "other boilers", "low temperature boilers" and "condensing boilers". The Boiler Efficiency Directive defines "standard boilers", "low temperature boilers" and "condensing boilers". Depending on the legislation applied, a boiler can be both "a standard boiler" and an "other boiler"."
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
NOTE This general standard and the specific standards (see Part 2) provide requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard or a specific standard, the risk associated with this alternative construction will need to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard is not intended to cover appliances intended for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex EE).
This European Standard is not intended to cover appliances designed and constructed to burn gas containing toxic components.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15502-1:2021(Main)
Gas-fired heating boilers - Part 1: General requirements and tests
SIST EN 15502-1:2022

This European Standard specifies the common requirements and test methods, as well as the classification, marking and energy labelling of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard is to be used in conjunction with the specific Parts 2 (Part 2-1 and following ones).
This European Standard applies to boilers of types B and C.
NOTE For further background information on appliance types see CEN/TR 1749:2014 [1].
a) that use one or more combustible gases of the three gas families at the pressures stated in EN 437;
b) where the temperature of the water is below or above 105 °C during normal operation;
c) where the maximum operating pressure in the water circuit does not exceed 6 bar;
d) which can give rise to condensation under certain circumstances;
e) which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler" or an "other boiler". If no declaration is given the boiler is to be considered both a "standard boiler" and an "other boiler";
NOTE The Ecodesign Directive defines "other boilers", "low temperature boilers" and "condensing boilers". The Boiler Efficiency Directive defines "standard boilers", "low temperature boilers" and "condensing boilers". Depending on the legislation applied, a boiler can be both "a standard boiler" and an "other boiler"."
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
NOTE This general standard and the specific standards (see Part 2) provide requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard or a specific standard, the risk associated with this alternative construction will need to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard is not intended to cover appliances intended for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex EE).
This European Standard is not intended to cover appliances designed and constructed to burn gas containing toxic components.

  • Standard
    213 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    215 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-3:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 3: Design and dimensioning (ISO 11855-3:2021)
SIST EN ISO 11855-3:2021

This document establishes a system design and dimensioning method to ensure the heating and cooling capacity of the radiant heating and cooling systems.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day