EN 13530-2:2002/A1:2004
(Amendment)Cryogenic vessels - Large transportable vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
Cryogenic vessels - Large transportable vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
Inner vessel stiffening rings.
Kryo-Behälter - Große ortsbewegliche vakuum-isolierte Behälter - Bemessung, Herstellung und Prüfung
Récipients cryogéniques - Grands récipients transportables isolés sous vide - Partie 2: Conception, fabrication, inspection et essais
Kriogene posode - Velike premične, vakuumsko izolirane posode - 2. del: Načrtovanje, izdelava, nadzor in preskus
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2004
.ULRJHQHSRVRGH9HOLNHSUHPLþQHYDNXXPVNRL]ROLUDQHSRVRGHGHO
1DþUWRYDQMHL]GHODYDQDG]RULQSUHVNXV
Cryogenic vessels - Large transportable vacuum insulated vessels - Part 2: Design,
fabrication, inspection and testing
Kryo-Behälter - Große ortsbewegliche vakuum-isolierte Behälter - Bemessung,
Herstellung und Prüfung
Récipients cryogéniques - Grands récipients transportables isolés sous vide - Partie 2:
Conception, fabrication, inspection et essais
Ta slovenski standard je istoveten z: EN 13530-2:2002/A1:2004
ICS:
23.020.40 Proti mrazu odporne posode Cryogenic vessels
(kriogenske posode)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13530-2:2002/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2004
ICS 23.020.40
English version
Cryogenic vessels - Large transportable vacuum insulated
vessels - Part 2: Design, fabrication, inspection and testing
Récipients cryogéniques - Grands récipients transportables Kryo-Behälter - Große ortsbewegliche, vakuum-isolierte
isolés sous vide - Partie 2: Conception, fabrication, Behälter - Teil 2: Bemessung, Herstellung und Prüfung
inspection et essais
This amendment A1 modifies the European Standard EN 13530-2:2002; it was approved by CEN on 9 January 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13530-2:2002/A1:2004: E
worldwide for CEN national Members.
Foreword
This document (EN 13530-2:2002/A1:2004) has been prepared by Technical Comm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.