EN 2600:2018
(Main)Aerospace series - Designation of metallic semi-finished products - Rules
Aerospace series - Designation of metallic semi-finished products - Rules
This document specifies the designation rules for metallic semi-finished products given in Table 1, used in aerospace construction.
It is applicable only if referred to in the metallic semi-finished product standard.
Luft- und Raumfahrt - Bezeichnung von metallischen Halbzeugen - Regeln
Série aérospatiale - Désignation des demi-produits métalliques - Règles
Aeronavtika - Označevanje kovinskih polizdelkov - Pravila
Ta dokument določa pravila za označevanje kovinskih polizdelkov iz tabele 1, ki se uporabljajo pri aeronavtiki.
Uporablja se le, če je naveden v standardu kovinskih polizdelkov.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Bezeichnung von metallischen Halbzeugen - RegelnSérie aérospatiale - Désignation des demi-produits métalliques - RèglesAerospace series - Designation of metallic semi-finished products - Rules49.025.05Železove zlitine na splošnoFerrous alloys in generalICS:Ta slovenski standard je istoveten z:EN 2600:2018SIST EN 2600:2019en,fr,de01-marec-2019SIST EN 2600:2019SLOVENSKI
STANDARD
SIST EN 2600:2019
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2600
December
t r s z ICS
English Version
Aerospace series æ Designation of metallic semiæfinished products æ Rules Série aérospatiale æ Désignation des demiæproduits métalliques æ Règles
Luftæ und Raumfahrt æ Bezeichnung von metallischen Halbzeugen æ Regeln This European Standard was approved by CEN on
s y September
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t x r rã t r s z ESIST EN 2600:2019
EN 2600:2018 (E) 2 Contents
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Designation scheme . 4 Annex A (normative)
Codes for metallic semi-finished product standards . 7 Annex B (normative)
Codes for thickness, diameter, across-flats, width, length . 8 Annex C (normative)
Codes for cross-section dimensions of sections . 12 C.1 Beaded L-section, extruded . 12 C.2 L-section, extruded . 13 C.3 Chanel section, extruded . 14 C.4 T-section, extruded . 15 C.5 L-section, folded profiles . 16 C.6 L-section, folded profiles with internally lipped flanges . 17 C.7 U-section, folded profiles . 18 C.8 U-section, folded profiles with externally lipped flanges . 19 C.9 U-section, folded profiles with internally lipped flanges . 20 C.10 Z-section, folded profiles . 21 C.11 Z-section, folded profiles with one lipped flange . 22 C.12 Z-section, folded profiles with lipped flanges . 23 C.13 Top-hat section, folded prof
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.