EN 14617-2:2004
(Main)Agglomerated stone - Test methods - Part 2: Determination of flexural strength (bending)
Agglomerated stone - Test methods - Part 2: Determination of flexural strength (bending)
This European Standard specifies a method for determination of flexural strength under a concentrated load (bending resistance) of agglomerated stone flat products.
Künstlich hergestellter Stein - Prüfverfahren - Teil 2: Bestimmung der Biegefestigkeit (Schwenkbiegen)
Diese Europäische Norm legt ein Verfahren zur Bestimmung der Biegefestigkeit (Biegebeständigkeit) von ebenen Kunststeinprodukten unter einer Mittellinienlast fest.
Pierre reconstituée - Méthodes d'essai - Partie 2: Détermination de la résistance à la flexion (traction)
Le présente Norme européenne spécifie une méthode de détermination de la résistance à la flexion (traction) sous charge centrée des produits plats en pierres reconstituées.
Aglomeriran kamen - Preskusne metode - 2. del: Ugotavljanje upogibne trdnosti (zvijanje)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2004
Aglomeriran kamen - Preskusne metode - 2. del: Ugotavljanje upogibne trdnosti
(zvijanje)
Agglomerated stone - Test methods - Part 2: Determination of flexural strength (bending)
Künstlich hergestellter Stein - Prüfverfahren - Teil 2: Bestimmung der Biegefestigkeit
(Schwenkbiegen)
Pierre reconstituée - Méthodes d'essai - Partie 2: Détermination de la résistance a la
flexion (traction)
Ta slovenski standard je istoveten z: EN 14617-2:2004
ICS:
91.100.15 Mineralni materiali in izdelki Mineral materials and
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 14617-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2004
ICS
English version
Agglomerated stone - Test methods - Part 2: Determination of
flexural strength (bending)
Pierre agglomérée - Méthodes d'essai - Partie 2: Künstlich hergestellter Stein - Prüfverfahren - Teil 2:
Détermination de la résistance à la flexion (traction) Bestimmung der Biegefestigkeit (Schwenkbiegen)
This European Standard was approved by CEN on 14 November 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14617-2:2004: E
worldwide for CEN national Members.
Contents page
Foreword.3
1 Scope .4
2 Normative references .4
3 Principle.4
4 Symbols .4
5 Apparatus .4
6 Preparation of the specimens.5
6.1 Sampling.5
6.2 Test specimens .5
6.2.1 Surface finish .5
6.2.2 Dimensions.6
6.2.3 Limit deviation.6
6.2.4 Conditioning before testing.6
7 Test procedure .6
8 Expression of the results.6
9 Test report .7
Annex A (normative) Statistical evaluation of tests results .8
A.1 Scope .8
A.2 Symbols and definitions .8
A.3 Statistical evaluation of test results .9
Foreword
This document (EN 14617-2:2004) has been prepared by Technical Committee CEN/TC 246 "Natural Stone", the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by August 2004, and conflicting national standards shall be withdrawn at the latest by
August 2004.
This document has been prepared in collaboration with JWG 229/246 "Agglomerated stones" (CEN/TC 246/WG4).
Test methods for agglomerated stones consist of the following:
prEN 14617-1, Agglomerated stone - Test methods – Part 1: Determination of apparent density and water absorption
EN 14617-2, Agglomerated stone – Test methods – Part 2: Determination of flexural strength (bending)
prEN 14617-3, Agglomerated stone - Test methods – Part 3: Determination of slipperiness
prEN 14617-4, Agglomerated stone - Test methods – Part 4: Determination of abrasion resistance
prEN 14617-5, Agglomerated stone - Test methods – Part 5: Determination of freeze and thaw resistance
prEN 14617-6, Agglomerated stone - Test methods – Part 6: Determination of thermal shock
prEN 14617-7, Agglomerated stone – Test methods – Part 7: Determination of ageing
prEN 14617-8, Agglomerated stone – Test methods – Part 8: Determination of resistance to fixing (dowel hole)
prEN 14617-9, Agglomerated stone - Test methods – Part 9: Determination of impact resistance
prEN 14617-10, Agglomerated stone – Test methods – Part 10: Determination of chemical resistance
prEN 14617-11, Agglomerated stone – Test methods – Part 11: Determination of linear thermal expansion coefficient
prEN 14617-12, Agglomerated stone – Test methods – Part 12: Determination of dimensional stability
prEN 14617-13, Agglomerated stone – Test methods – Part 13: Determination of electrical resistivity
prEN 14617-14, Agglomerated stone – Test methods – Part 14: Determination of surface hardness
prEN 14617-15, Agglomerated stone – Test methods – Part 15: Determination of compressive strength
prEN 14617-16, Agglomerated stone – Test methods – Part 16: Determination of dimensions and geometric
characteristics
prEN 14617-17, Agglomerated stone – Test methods – Part 17: Determination of biological resistance
Annex A is normative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain,
Sweden, Switzerland and United Kingdom.
1 Scope
This European Standard specifies a method for determination of flexural strength under a concentrated load
(bending resistance) of agglomerated stone flat products.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 12372, Natural stone test methods - Determination of flexu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.