EN ISO 14529-1:1999
(Main)Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14529-1:1999)
Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14529-1:1999)
1.1 This part of ISO 14529 establishes a data block system for the designation of melamine/phenolic powder
moulding compounds (MP-PMCs).
1.2 The various types of MP-PMC are differentiated from each other by a classification system based on
information about the filler/reinforcement type and content, the intended method of processing, any special
properties and those of the special properties used specifically for designation purposes (designatory properties).
1.3 This part of ISO 14529 is applicable to all MP-PMCs ready for normal use in the form of powder, granules or
ground material.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 14529 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
ISO 14529-2, if suitable.
1.5 Whenever general requirement data, as covered by ISO 14529-3, need to be indicated, this is also done
using this data block system.
1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the
system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.
Kunststoffe - Rieselfähige Melamin/Phenol-Formmassen (MP-PMC) - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 14529-1:1999)
1.1 In diesem Teil von ISO 14529 wird ein Daten-Blocksystem zur Bezeichnung von rieselfähigen Melamin/Phenol-Formmassen (MP-PMC) festgelegt. 1.2 Die verschiedenen Typen von MP-PMC werden mit einem Einteilungssystem voneinander unterschieden, das auf Angaben über Füll-/Verstärkungsstoffanteil und Art, v vorgesehene Verarbeitungs- und/oder Herstellungsverfahren, Angaben zu besonderen Eigenschaften und jenen besonderen Eigenschaften beruht, die spezifisch zur Bezeichnung verwendet werden (kennzeichnende Eigenschaften).
Plastiques - Poudres à mouler à base de mélamine/phénol (MP-PMC) - Partie 1: Système de désignation et base de spécification (ISO 14529-1:1999)
1.1 La présente partie de l'ISO 14529 établit un système de blocs de données pour la désignation des poudres à
mouler à base de mélamine/phénol (MP-PMC).
1.2 Les types de MP-PMC sont différenciés les uns des autres par un système de classification basé sur des
informations relatives au type et à la teneur en charges/matériaux de renforcement, à la méthode de mise en
oeuvre prévue, aux propriétés particulières en général et à celles utilisées spécifiquement pour les besoins de la
désignation (propriétés de désignation).
1.3 La présente partie de l'ISO 14529 est applicable à tous les MP-PMC prêts à l'emploi pour un usage courant
sous forme de poudres, grains ou matériaux broyés.
1.4 Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les
mêmes performances. La présente partie de l'ISO 14529 ne comporte pas de données sur la conception, les
performances ou les conditions de mise en oeuvre qui peuvent être exigées pour spécifier un matériau pour une
application et/ou une méthode de mise en oeuvre particulière. Si de telles caractéristiques supplémentaires sont
nécessaires, elles doivent être déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 14529-2, le
cas échéant.
1.5 Chaque fois qu'il est nécessaire d'indiquer certaines exigences générales telles que traitées dans
l'ISO 14529-3, on utilise pour ce faire le présent système de blocs de données.
1.6 Pour garantir que la signification des lettres-codes et des nombres-codes demeure non ambiguë et pour
éviter toute contradiction au sein du système, les nouveaux lettres-codes et nombres-codes à utiliser dans les
blocs de données 1, 2 ou 3 doivent être approuvés par les secrétariats de l'ISO/TC 61/SC 1, SC 12 et SC 13 avant
utilisation.
Polimerni materiali - Melamin/fenolne praškaste zmesi za oblikovanje (MF- PMCS) - 1. del: Sistem označevanje in podlage za specifikacije (ISO 14529-1:1999)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2000
3ROLPHUQLPDWHULDOL0HODPLQIHQROQHSUDãNDVWH]PHVL]DREOLNRYDQMH 0)30&6
GHO 6LVWHPR]QDþHYDQMHLQSRGODJH]DVSHFLILNDFLMH ,62
Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 1:
Designation system and basis for specifications (ISO 14529-1:1999)
Kunststoffe - Rieselfähige Melamin/Phenol-Formmassen (MP-PMC) - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 14529-1:1999)
Plastiques - Poudres a mouler a base de mélamine/phénol (MP-PMC) - Partie 1:
Systeme de désignation et base de spécification (ISO 14529-1:1999)
Ta slovenski standard je istoveten z: EN ISO 14529-1:1999
ICS:
83.080.10 Duromeri Thermosetting materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 14529-1
First edition
1999-11-15
Plastics — Melamine/phenolic powder
moulding compounds (MP-PMCs) —
Part 1:
Designation system and basis for
specifications
Plastiques — Poudres à mouler à base de mélamine/phénol (MP-PMC) —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 14529-1:1999(E)
©
ISO 1999
ISO 14529-1:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved
ISO 14529-1:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 14529 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14529-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
After a transition period of, at the most, four years, the three parts of ISO 14529 (see below) will replace
ISO 4896:1990, of which they constitute a technical revision.
ISO 14529 consists of the following parts, under the general title Plastics — Melamine/phenolic powder moulding
compounds (MP-PMCs):
� Part 1: Designation system and basis for specifications
� Part 2: Preparation of test specimens and determination of properties
� Part 3: Requirements for selected moulding compounds
© ISO 1999 – All rights reserved iii
INTERNATIONAL STANDARD ISO 14529-1:1999(E)
Plastics — Melamine/phenolic powder moulding compounds
(MP-PMCs) —
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of ISO 14529 establishes a data block system for the designation of melamine/phenolic powder
moulding compounds (MP-PMCs).
1.2 The various types of MP-PMC are differentiated from each other by a classification system based on
information about the filler/reinforcement type and content, the intended method of processing, any special
properties and those of the special properties used specifically for designation purposes (designatory properties).
1.3 This part of ISO 14529 is applicable to all MP-PMCs ready for normal use in the form of powder, granules or
ground material.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 14529 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
ISO 14529-2, if suitable.
1.5 Whenever general requirement data, as covered by ISO 14529-3, need to be indicated, this is also done
using this data block system.
1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the
system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 14529. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 14529 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 75-2:1993, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite.
1)
ISO 179-1:— , Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test.
1) To be published. (Revision of ISO 179:1993)
© ISO 1999 – All rights reserved 1
ISO 14529-1:1999(E)
ISO 472:1999, Plastics — Vocabulary.
ISO 1043-1:1997, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics.
2)
ISO 1043-2:— , Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials.
ISO 4896:1990, Plastics — Melamine/phenolic moulding materials — Specification.
ISO 14529-2:1999, Plastics — Melamine/phenolic powder
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.