prEN ISO/ASTM 52969
(Main)Additive manufacturing of metals - Non-destructive testing and evaluation - Classification of imperfections in DED parts (ISO/ASTM DIS 52969:2025)
Additive manufacturing of metals - Non-destructive testing and evaluation - Classification of imperfections in DED parts (ISO/ASTM DIS 52969:2025)
This document specifies the classification imperfections likely to be generated during an additive manufacturing process by DED for metallic parts.
This document also indicates the most probable causes of the formation of imperfections and includes illustrations.
Acceptance criteria for imperfections are not included in this document.
Additive Fertigung für Metalle - Zerstörungsfreie Prüfung und Bewertung - Fehlerklassifizierung in DED-Teilen (ISO/ASTM DIS 52969:2025)
Fabrication additive de métaux - Essais non destructifs et évaluation - Classification des imperfections dans les pièces DED (ISO/ASTM DIS 52969:2025)
Dodajalna izdelava kovinskih izdelkov - Neporušitveno preskušanje in vrednotenje - Razvrstitev nepravilnosti v izdelkih, izdelanih z usmerjenim nanašanjem materiala z energijo (DED) (ISO/ASTM DIS 52969:2025)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2025
Dodajalna izdelava kovinskih izdelkov - Neporušitveno preskušanje in vrednotenje
- Razvrstitev nepravilnosti v izdelkih, izdelanih z usmerjenim nanašanjem
materiala z energijo (DED) (ISO/ASTM DIS 52969:2025)
Additive manufacturing of metals - Non-destructive testing and evaluation - Classification
of imperfections in DED parts (ISO/ASTM DIS 52969:2025)
Additive Fertigung für Metalle - Zerstörungsfreie Prüfung und Bewertung -
Fehlerklassifizierung in DED-Teilen (ISO/ASTM DIS 52969:2025)
Fabrication additive de métaux - Essais non destructifs et évaluation - Classification des
imperfections dans les pièces DED (ISO/ASTM DIS 52969:2025)
Ta slovenski standard je istoveten z: prEN ISO/ASTM 52969
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
25.030 3D-tiskanje Additive manufacturing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/ASTM DIS
ISO/TC 261
Additive manufacturing of
Secretariat: DIN
metals — Non-destructive testing
Voting begins on:
and evaluation — Classification of
2025-04-14
imperfections in DED parts
Voting terminates on:
ICS: 25.030; 19.100
2025-07-07
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
© ISO/ASTM International 2025
ISO/ASTM DIS 52969:2025(en)
DRAFT
ISO/ASTM DIS 52969:2025(en)
International
Standard
ISO/ASTM DIS 52969
ISO/TC 261
Additive manufacturing of
Secretariat: DIN
metals — Non-destructive testing
Voting begins on:
and evaluation — Classification of
imperfections in DED parts
Voting terminates on:
ICS: 25.030; 19.100
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
© ISO/ASTM International 2025
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
USER PURPOSES, DRAFT INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
BE CONSIDERED IN THE LIGHT OF THEIR
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
ISO copyright office ASTM International
NATIONAL REGULATIONS.
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
RECIPIENTS OF THIS DRAFT ARE INVITED
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
TO SUBMIT, WITH THEIR COMMENTS,
Phone: +41 22 749 01 11 Phone: +610 832 9634
NOTIFICATION OF ANY RELEVANT PATENT
Fax: +610 832 9635
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org Email: khooper@astm.org
Website: www.iso.org Website: www.astm.org
Published in Switzerland Reference number
© ISO/ASTM International 2025
ISO/ASTM DIS 52969:2025(en)
© ISO/ASTM International 2025 – All rights reserved
ii
ISO/ASTM DIS 52969:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification of imperfections . 2
4.1 General .2
4.2 Designation .2
4.3 Detailed classification of imperfections occurring in DED additive manufacturing .3
4.3.1 General .3
4.3.2 Crack .3
4.3.3 Porosity . . .3
4.3.4 Inclusion .3
4.3.5 Lack of fusion .3
4.3.6 Shape imperfection and dimensional imperfection.3
4.3.7 Other imperfection .3
Annex A (informative) Illustration of imperfections produced in DED .15
Bibliography .22
© ISO/ASTM International 2025 – All rights reserved
iii
ISO/ASTM DIS 52969:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 261, Additive manufacturing, in cooperation with
ASTM Committee F42, Additive Manufacturing Technologies, on the basis of a partnership agreement
between ISO and ASTM International with the aim to create a common set of ISO/ASTM standards on
Additive Manufacturing.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
© ISO/ASTM International 2025 – All rights reserved
iv
ISO/ASTM DIS 52969:2025(en)
Introduction
Directed energy deposition (DED) additive manufacturing (AM) process category is of growing interest for
industry to build large metallic parts. It consists of using a concentrated energy (arc, laser, electron beam,
plasma) to melt and to deposit a filler material in the form of powder or wire to produce parts on a build
platform / substrate or to add functions to an existing part. In both cases, material is added to form entirely
or partially a part, which distinguishes AM from welding (the assembly of parts) and surface enhancement
(cladding, coating). All welding or cladding technologies that deposit material can potentially be used for AM.
In practice, only a few processes are of interest from an industrial perspective, because the chosen process
must at least be able to be automated and, much better, be robotized, productive, and able to produce objects
with minimum material removal to obtain near net shape part after manufacturing. The family of DED AM
process categories includes, as defined in ISO/ASTM 52900:
— DED-LB/P and DED-LB/W
— DED-EB/W
— DED-Arc/W with arc technologies (MIG-MAG, plasma, TIG) which are also called WAAM (Wire Arc
Additive Manufacturing).
It is however essential to be able to produce parts competitively in comparison with more conventional
processes (machining, casting, etc.) or to justify this option by a significant reduction of the supply lead time
of a part. It is also essential to produce good quality parts. To this end, before carrying out destructive or non-
destructive testing and deciding on conformity, it is necessary to have a classification of the imperfections
resulting from these processes.
© ISO/ASTM International 2025 – All rights reserved
v
DRAFT International Standard ISO/ASTM DIS 52969:2025(en)
Additive manufacturing of metals — Non-destructive testing
and evaluation — Classification of imperfections in DED parts
1 Scope
This document specifies the classification of imperfections likely to be generated during an additive
manufacturing process by DED for metallic parts.
This document also indicates the most probable causes of the formation of imperfections and includes
illustrations.
Acceptance criteria for imperfections are not included in this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO/ASTM 52900, Additive manufacturing — General principles — Fundamentals and vocabulary
ISO 6520-1, Welding and allied processes — Classification of geometric imperfections in metallic materials —
Part 1: Fusion welding
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6520-1, ISO/ASTM 52900 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
bead
metal deposited during one passage of a deposition process using an energy source and material feeding
Note 1 to entry: an energy source is LB, EB or Arc.
Note 2 to entry: the form of the material is powder or wire.
[SOURCE: ISO/TR 25901-1, 2.1.8.4, modified]
3.2
imperfection
any discontinuity or deviation observed from a specification (geometrical, material integrity)
© ISO/ASTM International 2025 – All rights reserved
---------------------- P
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.